ULtraLoQ LATCH 5 Smart Fingerprint Lock User Guide
- June 3, 2024
- Ultraloq
Table of Contents
ULtraLoQ LATCH 5 Smart Fingerprint Lock
Ultraloq Terms & Policies
Before using all Ultraloq products, please read all applicable terms, rules, policies and usage provisions found atwww.u-tec.com/company/privacy. By using your Ultraloq, you agree to be bound by the U-tec Privacy Policy.
Need help?
To get help or learn morehttps://support.u-tec.com
Exterior
Low battery
Communication
– Numbers
Back Enter
LED Indicator
Shows you authorized or denied access.
Touchscreen
Used to enter the code and unlock from the outside.
Fingerprint Reader
Read Fingerprint signals and unlock from the outside.
Backup Key Hole
Used to insert the key to unlock from outside.
Interior
Add Lock to U-tec App
Search on app store
Download App
Create Account
Add a New Device and Add a New User to the Lock
Add the lock to the App through two options
|
Bluetooth and GPS should be turned on in your smart phone to enable this feature.
---|---
Options 1
Add through Scanning
Step 1. Turn on the GPS and Bluetooth on your smart phone
Step 2. Select the device that you want to add in the scanning list
Step 3. Adding the device by following the instructions in the App
Options 2
Add through Categories
Step 1. Select Latch5 Fingerprint
Step 2. Select the device with strongest signal strength
Step 3. Create admin code
Step 4. Name the lock
Overall Process for Adding a New User
|
Please follow more detailed instructions in the App.
---|---
Set three different ways to unlock the door when add a new user
a. Add Fingerprint
b. Add Code
c. Add the User’s Email Account
Operate the Lock
Unlock with Fingerprint
2a Touch the center of the touch screen with registered Fingerprint.
2b. Turn down the handle to open the door.
Unlock with Code
1a. Touch the lock with the back of your hand to activate the lock.
1b. Enter the 4-8 digit code and press the , the LED will turn green if the code
is correct.
1c. Turn down the handle to open the door.
Unlock with App
3a. Connect the lock with U-tec App and tap the Unlock button.
3b. Turn down the handle to open the door.
If you come to any other questions, please don’t hesitate to visit our official support websitehttps://support.u-tec.com to get more help.
FAQ
Q.1 Can’t Unlock by inside handle after installation. How to Fix?****
A. Please check the thickness of your door. The thickness should be
between 1-3/8’’ to 1-3/4”(35 mm – 44mm).
Please install the spring if the door thickness is over 1.65”(42mm). Don’t
forget plug in the spindle. For thicker doors between 2” to 2-3/4″(51mm
-70mm), please order the Ultraloq Thick Door Kit on our official online store.
https://support.u-tec.com
Q2. How to reset the Latch 5 Fingerprint?
A. Please note all data will be erased if you reset Latch 5 Fingerprint to factory default settings. If you are using the U-tec App as Owner, please click “Delete and Reset” to remove the lock from your U-tec Account, then use the Reset Needle to push the Reset Button (above the batteries in the Interior Assembly) until you hear one long beep and two short beeps.
Q3. What if I lost the paired smartphone?****
A. Please go to www.u-tec.com/myutec.html or login U-tec App via another smartphone to change your U-tec account password.
Q4. How can I unlock the Latch 5 Fingerprint if the battery runs out?****
A. The low battery indicator light will be red when the batteries are gonging to be running out. The backup mechanical keys work always even when the batteries go dead.
Q5. What is the log capacity for the Latch 5 Fingerprint?****
A. Latch 5 Fingerprint supports maximum 1000 logs. The latest log will replace the oldest one once the log is full.
Q6. Does the Latch 5 Fingerprint work with accessories such as latch from third parties?****
A. It is recommended to use the original accessories for best performance and stability.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>