ULTRALOQ U Bolt WiFi Fingerprint Door Lock User Guide

ULTRALOQ U Bolt WiFi Fingerprint Door Lock

User Guide Video
Please watch our easy step by step User Guide video before attempting to use your U LTRALOQ U-Bolt WiFi Smart Lock.

Or you can also view the webiste directly. www.u-tec.com/lock/U-bolt- WiFifguide.

Product Overview

• Anti-peep Keypad
  Used to enter the code and unlock from outside.

• Backup Key Hole
  Used to insert the key to unlock in emergency s ituations.

• ULTRALOQ Button
  Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc. Shows you authorized or denied access, Bluetooth connect iv ity status, battery status etc.

Interior

• Reset Button
  Used to reset the lock to Factory Default settings.

• Battery Compartments
  Used to insert 4 AA Alkaline Battery, or manufacture suggested Lithium Battery. Don’t use Rechargeable Battery.

• Battery Cover
  Used to cover batteries and product label.

• Turn
  Used to unlock and lock the door from inside.

• LED Indicator
  Turns red when door is unlocked.

Low Battery Alarm
There will be low battery alert on the lock and App when battery is low. Tri- color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.

Lock Setup

• Step 1
  Scan above QR code to download the App, or search “U-tec”in App Store (iOS) and Google Play (Android).

• Step 2
  Open the App, register U-tec account and log in the account.

• Step 3
  Make sure the lock is in Factory Default Mode. Turn on Bluetooth on your smartphone, stay near the lock (within 10 feet ) and search the lock in the App. If you want to reset your lock to Factory default mode, Please check the page 14.

• Step 4
  Pair the lock in the App and start to use it.
  Note: Please refer to the guide in U-tec App for more information.

DON’TWANTTO USE THE APP?
Please go to page 15 for programming guide for Standalone Mode.

Using Your Lock

Unlock From Outside

• User Code
  Enter4-8 digit code and press ULTRALOQ Button to unlock.
  Note: You can press ULTRALOQ Button to turn on Keypad backlight.

• Smartphone
  Use your smartphone to unlock. Please refer to the guide in U-tecApp.

Lock From Outside
Press ULTRALOQ Button to lock manually. Enable Auto Lock feature and the lock will relock automatically.

Unlock From Inside
Rotate the kurn to a vertical position to unlock.

Reset the Lock
Please note all data will be erased if you reset U-Bolt WiFi to factory default. If you are using U-tec App as Owner, please click “Remove Device” to remove the lock from your U-tec Account,then you hear one long beep and two short beeps, it means reset successfully. If you have already removed the lock from your U-tec Account, but the lock doesn’t reset itself, please use a Reset Needle to push the Reset Button(at the bottom of Interior Assembly) for 10 seconds until you hear one long beep and two short beeps.

Replace Batteries
Please use 4 high-quality alkaline AA batteries for replacement when the battery is dead.

Emergency Key Override
Emergency Key Override can be used when the battery is dead.

Important Note
Please keep at least one key in secure location outside of your place.

Enable Or Disable Auto Lock

• Enable
  Please keep Bolt unlocked and press “1” button for 3 seconds until LED turns green and “1” button blinks.

• Disable
  Please keep Bolt unlocked and press “0” button for 3 seconds until LED turns green and “0” button blinks. This can also be set in U-tec App and Auto Lock timing can be programmed by yourself. Factory Default timing is 30 seconds.

Anti-peep Keypad
The lock supports up to 16-digit Vague Code. Just enter any 16-digit code, as long as a correct code is included in what you entered, you can open the door.

Standalone Mode Programming Guide

It is recommended to use U-tec App to program your lock. If you don’t have a smartphone or don’t want to use the App, you can use the programming instructions below.

Warning: Standalone Mode is NOT available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode.

Add Admin Code in Standalone Mode
Admin Code must be created first prior to any other programming. Only one Adm in Code is available.

Add User Code in Standalone Mode

Delete Admin and User
Please reset the lock to Factory Defau lt Mode to delete Admin and all Users.

• How to reset the lock in Standalone Mode?
  Please use a Reiset Needle to push the Reset Button (at the bottom of Inter or Assemb ly) for around 10 seconds until you hear one long beep and two short beeps.

FAQs

1. How to reset U-Bolt WiFi?
   Please note all data will be erased if you reset U-Bolt WiFi to factory default. If you are using U-tec App as Owner, please click “Delete and Reset” to remove the lock from your U-tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 10 seconds until you hear one long beep and two short beeps. If U-Bolt WiFi is working as Standalone Mode, please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 10 seconds until you hear one long beep and two short beeps.

2. What if I lost the paired smartphone?
   Please go to www.u-tec.com/myutec.html or login U-tec App via another smartphone to change your U-tec Account password.

3. How can I unlock U-Bolt WiFi if battery runs out?
   There will be low battery alert on the lock and App when battery is low. Red LED will flash 3 times along with 3 beeps when the lock is activated. Please replace batteries. If battery runs out, you can use the backup key to unlock.

4. What’s the difference between Owner, Admin, Normal User and Temporary User?
   Owner is the person who owns U-Bolt WiFi and registers it in U-tec App originally. Owner has all privileges. Admin can always unlock via code or App. Admin can add or delete Admin and Users, control all lock settings and view logs. Normal User can always unlock via code or App. Temporary User has limited access within specific time range.

5. Does U-Bolt WiFi work with accessories such as bolt from third party?
   It is recommended to use the original accessories for best performance and stability.

6. What is the user capacity for U-Bolt WiFi?
   U-Bolt WiFi supports maximum 50 users and each user can register 1 code.

7. What is the log capacity for U-Bolt WiFi?
   U-Bolt WiFi supports maximum 1000 logs. The latest log will replace the oldest one once log is full.

8. How to extend battery life of ULTRALOQ U-Bolt WiFi?
   You can disable the Remote Access to Lock function in the U-tec APP. After turning off the Remote Access to Lock function,battery life will be approximately doubled. Remote operation,smart control such as Alexa, Google Assistant,IFTTT and smart notifications will all be unavailable if turned off.

9. Does ULTRALOQ U-Bolt WiFi need to be paired with an ULTRALOQ Bridge?
   No, it is a smart lock with built-in WiFi. No extra hub required.

10. What is the network requirement?
    U-Bolt Wifi can only work with the 2.4G WiFi network (5G WiFT NOT supported)

© 2023 U-tec Group Inc.
U-tec and ULTRALOQ brands and products are trademarked and protected under law in the United States. Unauthorized use is prohibited. ULTRALOQ is sub-brand of U-tec Group Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>