ULTRALOQ B0BN69J959 U-Bolt WiFi Smart Lock Installation Guide

June 14, 2024
Ultraloq

ULTRALOQ -logo

ULTRALOQ B0BN69J959 U-Bolt WiFi Smart Lock

Important Notes

  • Do not use a power drill for installation.
  • Install and test the lock with the door open to avoid being locked out.
  • Please read all the instructions before contacting customer support.
  • Please contact customer support before returning the product to the store.
  • DO NOT install the batteries before installing the lock!
  • Follow the instructions in sequential order!
  • This lock is designed for the following operating temperatures:
  • Outside: -31° F(-35°C) to 158° F (70°C)
  • Inside: 14° F (-10°C) to 131° F (55°C)
  • Suggest to use AA Alkaline Battery, or manufacture suggested Lithium Battery. Don’t use Rechargeable Battery.

Statements

ULTRALOQ Terms & Policies

Before using all ULTRALOQ products, please read all applicable terms, rules, policies and usage provisions found at www.u-tec.com/company/privacy. By using your ULTRALOQ, you agree to be bound by the U-tec Privacy Policy.

Need Help?
For technical documents and more Please visit support.u-tec.com

Packing List

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-1

Installation Guide

Installation Video

Please scan this QR code to watch the easy step by step installation video before attempting to install ULTRALOQ U-Bolt WiFi.
Or you can also view the webiste directly. www.u-tec.com/lock/U-bolt- WiFifguide

Preparing Door

Check the door’s dimensions.

  • Step1
    Measure to confirm that the door is between P/a”~ 1¾” (35 mm-45 mm) thick. If your door is thicker than 1 3/4″, please visit support.u-tec.com to get help.

  • Step2
    Measure to confirm that the diameter of the hole is 21/a” (53 mm)

  • Step3
    Measure to confirm that the backset is either 2 % “or 2 3/,;’ (60 mm or70 mm) .

  • Step4
    Measure to confirm that the diameter of the hole in the door edge is 1″ (25 mm).

  • StepS
    Measure to confirm the depth of the hole in the frame is at least 1″(25mm).

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-4

If you have a new door, please drill the holes according to Drill Template.

Installing Bolt and Strike

  • Step 1
    Install Bolt into the door. Make sure the UP 4 icon goes up.
    Note : Bolt is set for 2 ⅜” backset initially. It can be adjusted to 2 ¾” if needed. To adjust it please make sure the bolt is retracted, then, press it, twist and pull it or push it to your desired length.

  • Step 2
    Install Strike into the door frame.

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-5

Installing Exterior Assembly

  • Step1
    Keep Bolt retracted and the cylinder tail piece horizontal. Install Exterior Assembly. Please do not insert the mechanical key during installation .

  • Step2
    Align its two sticks with two holes on Bolt. The cable goes through the hole be/ow Bolt.

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-6

Installing Interior Assembly Mounting Plate

  • Step1
    Route the cable through the hole on Interior Assembly Mounting Plate.

  • Step2
    Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-7

Installing Interior Assembly

  • Step1
    Remove the battery cover of the Interior Assembly.

  • Step2
    Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until it is completed seated.

  • Step3
    Rotate the knob and keep it in a vertical position to stay unlocked .ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-9

  • Step4
    Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.ULTRALOQ-
B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-10

 Installing the Batteries and Performing the Door Handing Process

This step will teach your lock the orientation of your door and is crucial to lock operation.

  • Step1
    Rotate the knob and keep it in a horizontal position to stay locked .ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-11

  • Step2
    Insert 4 AA Alkaline Batteries.ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-
fig-12

  • Note: Any fingerprint or pressing any digit button for 4 times can unlock U-Bolt WiFi in Factory Default Mode.

  • Step3
    Install battery cover.

Installing the Door Sensor(Optional)

The door sensor lets you know whether the door is open or closed through the App. When the auto lock is enabled in the App, your ULTRALOQ will only lock itself when the door is closed.
Please do not mount the door sensor on the keypad side. Please do not mount the door sensor on the kind of metal door that interferes with the magnet inside the door sensor(ln this case, the door sensor sticks to the metal door magnetically). The door sensor can be installed on the wooden door or the kind of metal door that will not interfere with the door sensor(ln this case, the door sensor will not stick to the door magnetically).

Option 1 Installing with Sticker
Peel off either side of the sticker and push it against the door frame about 10s. Peel off the other side and secure the door sensor on the sticker firmly. Put on the door sensor cover at last.

Option 2 Installing with Screw F
Push the door sensor against the wall and secure it with Screw F. You may need to drill a hole first if the door frame is hard to screw in with Screw F directly. Put on the door sensor cover at last.

ULTRALOQ-B0BN69J959-U-Bolt-WiFi-Smart-Lock-fig-14

Note: Please refer to the guide in U-tec App for more information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals