ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock Installation Guide

June 14, 2024
Ultraloq

Ultraloq U-Bolt

Installation Guide

(V 2.3)

ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A0

Important Notes
  • Do not use a power drill for installation.

  • Install and test the lock with the door open to avoid being locked out.

  • Please read all the instructions before contacting customer support.

  • Please contact customer support before returning the product to the store.

  • DO NOT install the batteries before installing the lock!

  • Follow the instructions in sequential order!

  • This lock is designed for the following operating temperatures:
    Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
    Inside Lock Body: 14°F (-10°C) to 131°F (55°C)

  • Please must use AA Alkaline Battery and don’t use Lithium Battery or Rechargeable Battery.

Statements

To ensure the best service, please register your account at www.u-tec.com/register.html

Ultraloq Terms & Policies

Before using all Ultraloq products, please read all applicable terms, rules, policies and usage provisions found at www.u-tec.com/company/privacy. By using your Ultraloq, you agree to be bound by the U-tec Privacy Policy.

Need Help?

For technical documents and more Please visit support.u-tec.com

Packing List

Interior Assembly

| Exterior Assembly|

Interior Assembly Mounting Plate

---|---|---
| |
Strike| Bolt| Backup Key
| |
Screw A| Screw B| Screw C
| |
Screw D| Screw E| AA Alkaline Batteries
| |
May not be included for some regions
User Guide| Drill Template| Reset Needle
| |
Bridge

Optional

Installation Guide
Installation Video

Please scan this QR code to watch the easy step by step installation video before attempting to install Ultraloq U-Bolt .
Or you can also view the website directly. www.u-tec.com/lock/U-bolt/guide

1. Preparing Door Check the door’s dimensions.

Step 1
Measure to confirm that the door is between 1 3/8″- 1 3/4″ (35 mm- 45 mm) thick.

Step 2
Measure to confirm that the diameter of the hole is 21/8″ (53 mm)

Step 3
Measure to confirm that the backset is either 23/8″ or 23/4″ (60 mm or 70 mm) .

Step 4
Measure to confirm that the diameter of the hole in the door edge is 1″ (25 mm).

Step 5
Measure to confirm the depth of the hole in the frame is at least 1″(25mm).

ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A1

If you have a new door, please drill the holes according to Drill Template.

2. Installing Bolt and Strike

Step 1
Install Bolt into the door. Make sure the UP ↑ icon goes up.

Note: Bolt is set for 2 3/8″ backset initially. It can be adjusted to 2 3/4″ if needed.
To adjust it please make sure the bolt is retracted, then, press it, twist and pull it or push it to your desired length.

Step 2
Install Strike into the door frame.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A2

  1. Twist
  2. Pull
  3. Adjust the Bolt basket length
3. Installing Exterior Assembly

Step 1
Keep Bolt retracted and the cylinder tailpiece horizontal. Install Exterior Assembly. Please do not insert the mechanical key during installation .

Step 2
Align its two sticks with two holes on Bolt. The cable goes through the hole below Bolt.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A3

4. Installing Interior Assembly Mounting Plate

Step 1
Route the cable through the hole on Interior Assembly Mounting Plate.

Step 2
Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A4

5. Installing Interior Assembly

Step 1
Remove the battery cover of the Interior Assembly.

Step 2
Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until it is completed seated.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A5

  1. Pull Up

Step 3
Rotate the knob and keep it in a vertical position to stay unlocked.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A6

  1. Unlocked

Step 4
Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.

ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A7

6. Installing the Batteries and Performing the Door Handing Process

This step will teach your lock the orientation of your door and is crucial to lock operation.

Step 1
Rotate the knob and keep it in a horizontal position to stay locked.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A8

  1. Locked

Step 2
Insert 4 AA Alkaline Batteries.

 ULTRALOQ Smart Lock U Bolt Fingerprint Door Lock A9

Note: Any fingerprint or code can unlock U-Bolt Pro in Factory Default Mode.

Step 3
Install battery cover.

© 2021 U-tec Group Inc.
U-tec and Ultraloq brands and products are trademarked and protected under law in the United States.
Unauthorized use is prohibited. Ultraloq is sub-brand of U-tec Group Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals