ULTRALOQ U-Bolt Smart Lock User Guide
- June 14, 2024
- Ultraloq
Table of Contents
Ultraloq U-Bolt User Guide
(v23)
Important Note
-
Do not use a power drillfor installation.
-
Install and test the lock with the door open to avoid being locked out.
-
Please read all the instructions before contacting customer support.
-
Please contact customer support before returning the product to the store.
-
DO NOT install the batteries before installing the lock!
-
Follow the instructions in sequential order!
-
This lockis designed for the following operating temperatures:
Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
Inside Lock Body: 14°F (-10°C) to 131°F (55°C) -
Please must use AA Alkaline Battery and don’t use Lithium Battery or Rechargeable Battery.
Statements
Toensure the best service, please register your account at www.u-tec.com/register.html
Ultraloq Terms and Policies
Before using all Ultraloq products, please read all applicable terms, rules,
policies and usage provisions found at
www.u-tec.com/company/privacy. By using
your Ultralog, you agree to be bound by the U-tec Privacy Policy.
Need Help?
For technical documents and more
Please visit support.u-tec.com
Packing List
Installation Video
https://www.u-tec.com/lock/u-bolt/guide
Please scan this QR code to watch the easy step by step installation video
before attempting to install Ultralog U-Bolt .
Oryou canalso view the webiste directly,
www.u-tec.com/lock/U-bolt/guide
-
Preparing Door
Check the door’s dimensions.
Step 1
Measure to confirm that the door is between 1%~ 1%,(35 mm- 45 mm) thick.
step 2
Measure to confirm that the diameter of the hole is 21″ (53 mm)
Step 3
Measure to confirm that the backset is either 2% or 2% (60 mmor 70 mm).
Step 4
Measure to confirm that the diameter of the hole in the door edgeis 1″ (25 mm).
Step 5
Measure to confirm the depth of the hole in the frame is at least 1’25mm).If’you have a new door, please drill the holes according to Drill Template. -
Installing Bolt and Strike
Step1
Install Bolt into the door. Make sure the UP 4 icon goes up.
Note: Boltis set for 2% backset nitially. It can be adjusted to 2% if needed.
Toadjust it please make sure the bolt is retracted, then, press i, twist and pullitor pushit to your desired length.
Step2
Install Strike into the door frame. -
Installing Exterior Assembly
Step1
Keep Bolt retracted and the cylinder tailpiece horizontal.
Install Exterior Assembly. Please do not insert the mechanical key during installation.
Step2
Alignits two sticks with two holes on Bolt. The cable goes through the hole below Bolt. -
Installing Interior Assembly Mounting Plate
Step1
Route the cable through the hole on Interior Assembly Mounting Plate.
Step2
Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D. -
Installing Interior Assembly
Step1
Remove the battery cover of the Interior Assembly.
Step2
Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until it is completed seated. Step3
Rotate the knob and keep it in a vertical position to stay unlocked. Step4
Attach Interior Assembly to Mounting Plate and tighten 2 Screws E. -
Installing the Batteries and Performing the Door Handing Process
This step will teach your lock the orientation of your door and scrucial tolock operation.
Step1
Rotate the knob and keep itin a horizontal position to stay locked. Step2
Insert 4 AA Alkaline Batteries. Note: Any fingerprint or code can unlock U-Bolt Proin Factory Default Mode.
Step3
Install battery cover.
©2021 U-tec Group Inc.
U-tec and Ultralog brands and products are trademarked
and protected under law
in the United States.
Unauthorized use s prohibited. Ultralog is sub-brand of
U-tec Group Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>