ULTRALOQ ‎U-BOLT-PRO-WiFi Smart Lock with Door Sensor User Guide

ULTRALOQ ‎U-BOLT-PRO-WiFi Smart Lock with Door Sensor

User Guide Video
Please watch our easy step by step User Guide video before attempting to use your Ultraloq U-Bolt Pro WiFi Smart Lock.

Or you can also view the webiste directly. www.u-tec.com/lock/U-bolt_pro_WiFi/guide

Product Overview

Exterior

• Anti-peep Keypad
  Used to enter the code and unlock from outside.

• Advanced Fingerprint Reader
  Used to verify your finger and unlock from the outside.

• Backup Key Hole
  Used to insert the key to unlock in emergency situations.

• Micro USB (SV)
  Used to connect power bank to activate the lock when battery runs out.

• Tri-color LED Indicator
  Shows you authorized or denied access, Bluetooth connectivity status, battery status etc.

• Ultraloq Button
  Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc.

Interior

• Reset Button
  Used to reset the lock to Factory Default settings. If the lock was paired to App, please must click “Delete” to remove the device from App.

• Battery Compartments
  Used to insert 4 AA alkaline batteries.
  Note: Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don’t recommend them because they don’t give you a lot of time to change your batteries before the lock is completely dead. Please don’t use any Rechargeable Battery.

• Battery Cover
  Used to cover batteries and product label.

• Knob
  Used to unlock and lock the door from inside.

• LED Indicator
  Turns red when door is unlocked.

Low Battery Alarm
There will be low battery alert on the lock and App when battery is low. Tri- color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.

Lock Setup

Scan QR code to download the App:

1. Step 1
   Scan above QR code to download the App, or search “U-tec”in App Store (iOS) and Google Play (Android).

2. Step 2
   Open the App, register U-tec account and log in the account.

3. Step 3
   Make sure the lock is in Factory Default Mode. Turn on Bluetooth on your smartphone, stay near the lock (within 10 feet ) and search the lock in the App.

4. Step4
   Pair the lock in the App and start to use it.
   Note: Please refer to the guide in U-tec App for more information.

DON’T WANT TO USE THE APP?
Please go to page 15 for programming guide for Standalone Mode.

Using Your Lock

Unlock From Outside

• User Code
  Enter 4-8 digit code and press Ultraloq Button to unlock.

• Fingerprint
  Place your finger on Fingerprint Reader to unlock.

• Smartphone
  Use your smartphone to unlock. Please refer to the guide in U-tecApp.

Lock From Outside
Press Ultraloq Button to lock manually. Enable Auto Lock feature and the lock will relock automatically.

Unlock From Inside
Rotate the knob to a vertical position to unlock.

Reset the Lock
Please note all data will be erased if you reset U-Bolt Pro WiFi to factory default. If you are using U-tec App as Owner, please click “Delete and Reset” to remove the lock from your U-tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

Replace Batteries
Please use 4 high-quality alkaline AA batteries for replacement when the battery is dead.

5V Emergency Power
Micro USB interface is used to connect regular 5V power bank to activate the lock in case the battery is dead.

Emergency Key Override
Emergency Key Override can be used when the battery is dead. Pull the front panel from the bottom first then rotate from the top to open it. You can see Backup Key Hole inside. Insert the key and rotate to unlock,just like any lock.

Important Note
Please keep at least one key in secure location outside of your place.

Enable Or Disable Auto Lock

• Enable
  Please keep Bolt unlocked and press “1” button for 3 seconds until LED turns green and “1” button blinks.

• Disable
  Please keep Bolt unlocked and press “0” button for 3 seconds until LED turns green and “0” button blinks.
  This can also be set in U-tec App and Auto Lock timing can be programmed between 10 seconds to 5 minutes. Factory Default timing is 30 seconds.

Anti-peep Keypad
The lock supports up to 16-digit Vague Code. Just enter any 16-digit code, as long as a correct code is included in what you entered, you can open the door.

Place Finger

1. For a higher recognition rate, please try to cover the Fingerprint Reader completely with your finger, touching the surrounding metal ring.
2. Make sure that your finger and Fingerprint Reader are clean and dry. For Fingerprint Reader, use a clean, lint-free cloth to wipe off any dirt or debris.
3. Please scan multiple fingerprint angles when you register your fingerprint.
4. While scanning your finger, you shouldn’t tap too quickly or move your finger around.
5. If you have trouble enrolling one finger, try another.
6. U-Bolt Pro WiFi fingerprint sensor has self-study function which the verification rate will be improved after multiple success.

Standalone Mode Programming Guide

It is recommended to use U-tec App to program your lock. If you don’t have a smartphone or don’t want to use the App, you may follow the programming instructions below.

Warning
Standalone Mode is NOT available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode.

Add Admin Code in Standalone Mode
Admin Code must be created first prior to any other programming. Only one Admin Code is available.

Add User Code in Standalone Mode

Add Fingerprint in Standalone Mode

Delete Adm in and User
Please reset the lock to Factory Default Mode to delete Ad min and all Users.

• How to reset the lock in Standalone Mode?
  Please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

FAQs

1. How to reset U-Bolt Pro WiFi?
   Please note all data will be erased if you reset U-Bolt Pro WiFi to factory default. If you are using U-tec App as Owner, please click “Delete and Reset” to remove the lock from your U-tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps. If U-Bolt Pro WiFi is working as Standalone Mode, please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

2. What if I lost the paired smartphone?
   Please go to www.u-tec.com/myutec.html or login U-tec App via another smartphone to change your U-tec Account password.

3. How can I unlock U-Bolt Pro WiFi if the battery runs out?
   There will be low battery alert on the lock and App when battery is low. Tri- color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.

4. Solution 1. Use the backup key to unlock.

5. Solution 2. Connect a 5V power bank to activate the lock temporarily.

6. What’s the difference between Owner, Adm in, Normal User and Temporary User?
   Owner is the person who owns U-Bolt Pro WiFi and registers it in U-tec App originally. Owner has all privileges. Admin can always unlock via fingerprint, code or App. Ad min can add or delete Ad min and Users, control all lock settings and view logs. Normal User can always unlock via fingerprint, code or App. Temporary User has limited access within specific time range.

7. Does U-Bolt Pro WiFi work with accessories such as bolt from third party?
   It is recommended to use the original accessories for best performance and stability.

8. What is the log capacity for U-Bolt Pro WiFi?
   U-Bolt Pro WiFi supports maximum 1,000 logs. The latest log will replace the oldest one once log is full.

9. What is the user capacity for U-Bolt Pro WiFi?
   U-Bolt Pro WiFi supports maximum 50 users and each user can register 1 code and 2 fingerprints.

10. How to extend battery life of Ultraloq U-Bolt Pro WiFi?
    You can disable the Remote Access to Lock function in the U-tec APP. After turning off the Remote Access to Lock function,battery life will be approximately doubled. Remote operation,smart control such as Alexa,Google Assistant,IFTTT and smart notifications will all be unavailable if turned off.

11. Does Ultraloq U-Bolt Pro WiFi need to be paired with an Ultraloq Bridge?
    No, it is a smart lock with built-in WiFi. No extra hub required.

12. What is the network requirement?
    U-Bolt Pro WiFi can only work with the 2.4G WiFi network (5G WiFi NOT supported).

© 2021 U-tec Group Inc.
U-tec and Ultraloq brands and products are trademarked and protected under law in the United States.
Unauthorized use is prohibited. Ultraloq is sub-brand of U-tec Group Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>