MICROTOUCH Titanium Trim Hair Cutting Tool User Manual

Thank you for your purchase of the

MicroTouch® Titanium Trim™.

Please read all instructions before you begin. For additional information including how to videos, please visit www.TitaniumTrim.com.

Important Safety Instructions

DANGER

To reduce the risk of electrical shock:

• Do not place or store the appliance where it is able to fall or be pulled into a tub or sink.
• Do not place appliance in or drop into water or other liquid.
• Do not reach for appliance if it has fallen into water.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Use this product only for its intended household use as described in this manual.
• Do not use the appliance with damaged or broken comb or with teeth missing from blades, as injury may result. Before each use, make certain the blade head is installed and working properly.
• Keep appliance away from heated surfaces.
• Do not use the appliance outdoors or where aerosol (spray) products are being used or where oxygen is being administered.

What’s Included

MicroTouch® Titanium Trim™

Cleaning Brush    Blade Guard (G)    ¼” / 6 mm (#2)   ½” / 13mm (#4)

2 AA Batteries Included         ¾” / 19 mm (#6)       1” / 25mm (#8)

Getting Started

Inserting Batteries

• The battery compartment is located on the bottom portion of the unit.
• To access the battery compartment, fully extend the handle then press the yellow battery icon button and pull apart (Image 1).
• Once apart, twist battery cover counterclockwise (following engraved arrow) to open (Image 2).
• Align two AA batteries, with the positive and negative positions indicated on the battery compartment. Insert the positive (+) end of each battery first.
• Close the compartment cover by pushing in and rotating clockwise until it clicks.
• Replace the handle onto the unit by lining it up with the channels on the unit (Image 3).
• Once you reach the locked position, press the yellow battery icon and push to fully close (Image 3).
• Always purchase the correct size and grade of battery most suitable for the intended use.
• Do not mix old and new batteries.
• Ensure the batteries are installed correctly with regard to polarity (+ and -). The unit will NOT operate if one or both batteries are inserted incorrectly.
• Remove batteries from equipment, which is not to be used for an extended period of time.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbonzinc), or rechargeable (nickel cadmium or nickel metal hydride) batteries.

How to Use MicroTouch® Titanium Trim™

Choosing the Correct Comb Attachment

• To choose the correct comb attachment, lay out all 4 comb attachments so the length indicated is visible.
• Each comb length specifies the length of hair that will remain after it is trimmed (¼”, ½”, ¾”, 1”).
• Slide the open end of the comb attachment over the blade head until it snaps into place (Image 4).
• To remove a comb attachment, firmly grasp the unit and tilt the comb slightly forward while pulling upward (Image 5).

NOTE: The 1” comb is different than the others.

• Only use the 1” comb with the guide surface against your head while cutting.
• This may require switching hands when changing directions.
• For proper lifting of the hair, the 1” comb only has one guide surface (Image 6).
• The other 3 combs included and Blade Guard may be used with either side against your head.

Cutting/Trimming Hair or Beard

With Comb Attachment

• For best results, use on dry hair and comb/brush hair prior to use to detangle any knots.
• When cutting/trimming for the first time, start by using the attachment with the longest setting in order for you to familiarize yourself with the product.
• Press on/off button (Image 7). The LED light will illuminate and the blade will begin to move.
• To begin, start at the top portion of your head, being sure to trim starting from the front and combing toward the back of your head (Image 8).
• Keep flat edge of the comb attachment against your head while moving it through your hair in short strokes.

Trimming Sides of Hair

• Move the unit from the back of your head to the front, being sure to comb in an upward and outward motion (Image 9).
• You can also trim the sides of your hair by moving the unit up and down.

TIP: The comb attachments can be used in either direction as desired. For best results, cut against the direction of hair growth and if you are not getting the desired trimming results, lift your hair from the scalp and comb through.

Trimming Beard

• Starting trimming under your chin (Image 10A) and work up and out toward your ears (Image 10B).

Trimming Hair on the Back of your Head

• Hold the unit horizontally.
• Move the unit in an upward and outward motion (Image 11).

Trimming Body Hair or Necklines

No Comb Attachment
NOTE: When trimming sensitive areas, be sure to use the blade guard (Image 12).
Press the on/off button. The LED light will illuminate and the blade will begin to move.

• To begin, hold the unit at a slight angle facing toward the hair and trim in the opposite direction of hair growth.
• Continue to trim until you reach desired results. DO NOT apply excess pressure to the blade. Doing so may result in injury to the skin and/or damage to the blade.

Extendable Handle

• The unit handle extends to allow for greater reach when trimming hard to reach areas.
• Grab the handle of the unit, gently pulling on it until it locks into the extended position.

NOTE: If you pull too hard on the extendable handle, it will separate from the unit.

Care and Maintenance

• Turn the unit off before cleaning.
• Take off comb attachments.
• Turn your unit to the side so the MicroTouch® logo is facing up and toward you.
• Remove the blade by pressing your thumb against the blade edge and push away from the unit (Image 13-14).

NOTE: Only one side of the blade is removable.

• Use included brush to remove any hair clippings from the main unit or around the blade.
  You can also use the brush to remove hair clippings from in between the teeth of the comb attachments.

• For excess hair clippings, the blade head (removed off the unit) and comb attachments can be rinsed under running water and placed on a towel to dry.

• Be sure the blade head is completely dry before putting it back on.

• The handle can be cleaned with a damp cloth, do not submerge under water.

• After cleaning, align the springs between the clips on the unit and snap together (Image 15-16).

Wayne, NJ 07470
Made in China © 2020 Ideavillage
customerservice@ideavillage.com
MTTITNMTRM091820MW

References

• Micro Touch® Titanium Trim™ - The All New At-Home Haircutting Tool & Precision Groomer!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>