MicroTouch IC-215P-AW3 Touch Computer User Guide
- June 5, 2024
- MICROTOUCH
Table of Contents
MicroTouch IC-215P-AW3 Touch Computer User Guide
About This Document
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of MICROTOUCH.
The information in this document is subject to change without notice. MICROTOUCH makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. MICROTOUCH reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of MICROTOUCH to notify any person of such revisions or changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective holders.
Compliance Information
For FCC (USA)
This equipment has been tested and fund to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. There limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For IC (Canada)
CAN ICES-3(A)/NMB-3(A)
For CE (EU)
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
Usage Notice
Warning – To prevent the risk of fire or shock hazards, and do not expose the product to moisture.
Warning – Please do not open or disassemble the product as this may cause electric shock.
Warning – Power cord shall be connected to a socket-outlet with earth connection.
Warning – The cable cover cannot be removed under normal use conditions.
Warning – Stability Hazard. The touch monitor may fall, causing serious personal injury or death. To prevent injury, this touch monitor must be securely attached to the wall in accordance with the installation instructions.
Precautions
Please follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Do :
- Turn off the product before cleaning.
- Use a soft cloth moistened with mild detergent to clean the product housing.
- Use only the qualified power adapter that comes with your device.
- Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.
Don’t :
- Do not use abrasive cleaners, waxes or solvents for your cleaning.
- Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
Caution
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Chapter 1
Product Introduction
1.1 Overview
The IC-215P-AW3 is a thin 21.5″ touch computer that offers a unique design with expandability and flexibility, making expansion and accessory installation easy. The versatility of IC-215P-AW3 is an exceptional choice for applications in all business sectors, especially in the retail market.
1.2 Feature
- Intel I3-7100U processor.
- Sleek design for a better user experience.
- Patented I/O design for better wiring management during install.
1.3 Specifications
1.4 Block Diagram
1.5 Interface Connectors
1.6 Package Overview
Warning!
This product is intended to be supplied by a UL Listed Power Adapter, rated
24Vdc, 5A minimum. (complied with LPS or PS2) Tma = 40 degree C minimum, and
the altitude of operation = 3048m minimum. If it needs further assistance with
purchasing the power source, please contact to MICROTOUCH for further
information.
Chapter 2
Product Installation
2.1 About VESA Mount
The IC-215P-AW3 conform to the “VESA Flat Display Mounting Interface Standard” which defines a physical mounting interface for touch computer, and corresponding with the standards of touch computer mounting devices, such as wall-mounted. The VESA mount is located on the back of this unit.
The IC-215P-AW1 may be wall mounted in the horizontal position (output connector facing down) or vertical position (output connector facing left or right).
Warning!
Please the correct screws! The distance between the back cover surface and the
bottom of the screw hole is 8 mm. Please use four M4 / 8 mm screws diameter
with proper length to mount your monitor. Note: The mounting stand must be
able to support at least 9.3 lbs (4.2 Kg).
2.2 Power On / Off Switch
2.3 Dimension
2.3.1 System Only
2.3.2 System with Stand
2.4 Optional Accessory Installation
Note : Please install/ dismantle the product when the computer system is in the shutdown state.
2.4.1 Install the Stand
Place stand module on back of touch computer and align the screw holes. Install the four M4 screws to fasten the stand.
2.4.2 Remove the Stand
Step 1: Loosen the screws
Step 2: Pull it to out from touch computer and remove stand module.
2.4.3 Install the Cables
2.4.3.1 Cable Organizer
Step 1: Pull down the cable cover for cables installation.
Step 2: To fit the plugs
Step 3: To assemble the cable cover.
Step 4: Driving a screw to fix cable cover
(The cable can be fixed above or below the cable cover) Step 4
2.4.4 Install the Camera Module
Camera Module max. 19g
Step 1: Remove the side cover.
Step 2: Connect the camera module cable to the touch computer.
Step 3: Install the two M3 screws to fasten the camera module.
2.4.5 Remove the Camera Module
Step 1: Loosen the screws.
Step 2: Remove the camera module cable from the touch computer.
Step 3: Replace the the side cover.
2.4.6 Install the MSR Module
MSR Module max. 62g.
Step 1: Remove the side cover.
Step 2: Connect the MSR module cable to the touch computer.
Step 3: The metal bracket hook into the gap between cover glass and bezel.
Step 4: Install the two M3 screws to fasten the MSR module. Step 4
2.4.7 Remove the MSR Module
Step 1: Loosen the screws.
Step 2: Remove the MSR module cable from the touch computer.
Step 3: To assemble the side cover.
Appendix
Declaration of the Presence Condition of the Restricted Substances
Marking
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>