SW-MOTECH BC.HTA.07.512.20000 Side Saddlebag Instruction Manual

June 3, 2024
SW-MOTECH

SW MOTECH logo BC.HTA.07.512.20000 Side Saddlebag
Instruction Manual
HTA.07.512.10000 HTA.07.512.11000

BC.HTA.00.401.10100L BC.HTA.00.402.10100R

MOUNTING INSTRUCTIONS

Revision:00 – Datum / Date: 02 – 2016
Legend Gear Side Carrier SLC

Thank you for choosing this premium product from SW-MOTECH.
($4 Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE  certifications), are also available for download at our webshop. >> www.sw-motech.com
Installation and/or maintenance of this product require good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing  carried out by a specialist workshop.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance  can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed.  Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Please observe any country-specific regulations concerning vehicle registration or operation as well as TUV regulations where applicable, If required, register installed parts in  the vehicle documents together with the appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn  off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Make sure to  use only the appropriate tools. During installation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and  hardware delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strong strength liquid thread locker.
If not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and nuts must be tightened according to DIN/ISO specifications. After installation make sure  that all parts and hardware previously removed are properly replaced.
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed and function of the vehicle is not hindered in any way. Cables and hoses must  not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. Regularly check (every 100 km) for the proper seating of all parts and  connections removed during installation.

PARTS LIST

No.| Art.-Nr. /
Item No. /| Part| Quantity| N-m
---|---|---|---|---
| HTA.07.512.1000./B| Legend Gear Side Carrier SLC teft| |
1| HTA.07.512.901.01| Side Carrier| 1/ 1|
2| M6 x 20; DIN 6912| Hexagon Socket Screw, short Head| 1/ 1| 9.6
3| HTA.00.152.081| Lock bolt| 1/ 1|
4| HTA.00.152.080| Guide Bolt| 3/ 3|
5| M6 x 20; DIN 7 9 9 1| Countersunk Screw; black| 2/ 2| 9.6
6| M8 x 45; DIN 912| Hexagon Socket Screw| 1/ 1| 23
7| M6 x 20; ISO 7380| Lenshead Screw| 1/ 1| 9.6
No.| Art.-Nr. /
Item No. /| Part| Quantity
| N-m
---|---|---|---|---
| HTA.07.512.1000./B| Legend Gear Side Carrier SLC teft| |
1| HTA.07.512.902.01| Side Carrier| 1/ 1|
2| M6 x 20; DIN 6912| Hexagon Socket Screw, short Head| 1/ 1| 9.6
3| HTA.00.152.081| Lock bolt| 1/ 1|
4| HTA.00.152.080| Guide Bolt| 3/ 3|
5| M6 x 20; DIN 7 9 9 1| Countersunk Screw; black| 2/ 2| 9.6
6| M8 x 45; DIN 912| Hexagon Socket Screw| 1/ 1| 23
7| M6 x 20; ISO 7380| Lenshead Screw| 1/ 1| 9.6

The second number indicates the total quantity of the listed part in the delivery.

SW MOTECH BC HTA 07 512 20000 Side Saddlebag

MOUNTING

SW MOTECH BC HTA 07 512 20000 Side Saddlebag - fig

Mount the parts to the side carrier (1] as shown in the drawing .
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.SW MOTECH BC HTA 07 512
20000 Side Saddlebag - fig 1

Remove the screws and the passenger seat, as shown in the  detail drawing.
Mount the side carrier (1) with the original Spacer (Orig.) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list
SW MOTECH BC HTA 07 512 20000 Side Saddlebag - fig 2

Mount the parts to the side carrier (1] as shown in the drawing .
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.

SW MOTECH BC HTA 07 512 20000 Side Saddlebag - fig 3

Remove the screws and the passenger seat, as shown in the detail drawing.
Mount the side carrier (1) with the original Spacer (Orig.) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list

Revision:01- Datum/ Date: 01 – 2018
Legend Gear Side Bag LC1 / LC2

 Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE  certifications), are also available for download at our webshop. >> www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance  can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no liability for damages caused by  improper fixation and handling.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration,
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn  off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with  your vehicle type.
ATTENTION: All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle  and remain clear of the exhaust stream. After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.
ATTENTION: Before riding and at each stop [every 200 km) check proper fixation of the product!
After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be  limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

LOADING INFORMATION

ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from moisture.
Additionally protect sensitive luggage l(e.g., electronic equipment) from moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130 km/h!

SW-MOTECH GmbH & Co. KG
Ernteweg 8/10 – 35282 Rauschenberg
– Germany
Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0]6425 / 81 6 8 – 10
infofasw-motech.comwww.sw- motech.com

PARTS LIST & CARE

SW MOTECH BC HTA 07 512 20000 Side Saddlebag - fig 4

CARE
Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough  cleaning tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).
We recommend to impregnate the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation [e.g. from  Fjallraven).
ATTENTION: Because the textile surfaces material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time  and by environmental factors [e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no Liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact  with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions.
SW-MOTECH assumes no Liability for paint damage and abrasions.

FIXATION

SW MOTECH BC HTA 07 512 20000 Side Saddlebag - fig
5

Fasten the Velcro closure of the side bag (1a/1b).
Revert the reinforced opening of the side bag (1a/1b) twice completely. SW
MOTECH BC HTA 07 512 20000 Side Saddlebag - fig 6

Fix the shown loops with the side-mounted hook buckles.SW MOTECH BC HTA 07
512 20000 Side Saddlebag - fig 7

Tighten the straps of the hook buckle.
Secure the opening of the side bag (1a/1b) with the shown strap.SW MOTECH BC
HTA 07 512 20000 Side Saddlebag - icon 1

Place the three openings of the quick release fastening system onto the locating bolts of the mounted SLC side carrier. SW MOTECH BC HTA 07 512
20000 Side Saddlebag - icon 2

Press the side bag [1a/1b) slightly downward, until it properly rests on SLC side carrier.
ATTENTION: Make sure that all three locating bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism!SW
MOTECH BC HTA 07 512 20000 Side Saddlebag - icon 3

To release the side bag [1a/1b) simply press the shown slider of the locking mechanism downward.

Copyright by
SW-MOTECH GmbH & Co. KG
Errors and omissions excepted. Technical and design modifications are subject to change.

SW MOTECH logo

SW-MOTECH GmbH & Co. KG
Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425
Ernteweg 8 / 1 0/ 8168 – 1 0
35282 Rauschenberg
infofasw-motech.com
Germany
www.sw-motech.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SW-MOTECH User Manuals

Related Manuals