BOSS AUDIO SYSTEMS BHD98 Harley Davidson Saddlebag Speaker Kit User Manual
- June 13, 2024
- BOSS AUDIO SYSTEMS
Table of Contents
BHD98
USER’S MANUAL
HARLEY DAVIDSON SADDLEBAG SPEAKER KIT
BHD98 Harley Davidson Saddlebag Speaker Kit
FITS SELECT 1998-2013 HARLEY DAVIDSON ROAD GLIDE AND
STREET GLIDE MOTORCYCLES
| |
---|---|---
POWERSPORTS| IPX RATING| IMPEDANCE
BHD98
Harley Davidson
Saddlebag Speaker Kit
Congratulations on your purchase of a POWERSPORTS Speaker System.
It has been engineered to bring you the highest level of performance. Its
quality will afford you years of listening pleasure.
Thank you for making your choice for POWERSPORTS entertainment!
Specifications
Mid Bass Driver: 6″x9″ {152x229mm) poly injection cone rubber surround
Tweeter: 1″ (25mm) Silk dome tweeter
Crossover network: Built-in
Impedance: 40hms
Pow·er Capacity: 150W MAX
Frequency Response: 70Hz – 20kHz
Sensitivity: 93d8 (1 watt/1 meter)
Dimensions:
9-1 /4″ {W) x 6-1 /2″ {H) x 3-1/2″(0)
(234 (W) x 164 (H) x 89 (D) mm)
Weight (in gift box): 13.45 lbs (6.1 kg)
All specifications subject to change without notice.
Introduction
The BOSS Audio Systems BHD98 Saddlebag Speaker kit allows the addition of 6″x9″ rear speakers to easily be installed into your existing factory bag lids. The included cut out template makes the cutting painless and installation a breeze. This rear speaker upgrade is designed to work perfectly with our BHD3F front kit (sold separately). This BHD98 fits 1998 to 2013 Harley Davidson Road Glide and Street Glide models. Simply plug in to the BHD3F (sold separately) amplifier for a complete audio upgrade without the hassle of serious modifications or paint.
What is included?
Before you begin installation please check that your system contains the following contents:
- (2) 6″x9″ (152x229mm) 2-way speakers
- (2) Saddlebag speaker grilles
- (2) 6″x9″ (152x229mm) bottom speaker protectors
- (2) 6″x9″ (152x229mm) plastic mounting rings
- (2) Red colored templates
- (1) Wire cable
- (1) Screw bag (4x20mm 8pcs, 4x12mm 10pcs)
- (2) Wire clamps
- (10) Plastic gaskets for speaker
- (12) Nylon wire straps
Dimensions:
Installation
-
Remove Saddle Bags from motorcycle.
(Note: Inside the bag you will find 2 pins that hold the bag in place. Turn pins to remove bags) -
Place a soft cover on secure table, then place the Bag on to table to avoid causing any scratching or damage to the bag.
-
With masking tape, cover the front edge of the bag lid where you will be placing the cutting template.
-
Test fit the template to make sure you have all painted surfaces covered with masking tape and that the template can be firmly mounted with no gaps.
-
Place template on bag lid and drill a screw in either one of the two center holes. Before drilling in the second screw, double check that the template is still in position and has not shifted. After that has been confirmed , drill the second screw into position. Now your template should be in place and have no visible gaps between the template and the bag lid.
-
With a 5/16 drill bit begin to drill out the 15 pilot holes on the template.
-
Using a jig saw or rotary drill, begin to cut along the template lines until all cuts have been made. Use care and go slow to ensure you make accurate cuts.
-
Remove template and masking tape.
-
Carefully sand the newly cut edges so that there is no debris or hanging material left from cutting.
-
If there is not a stock wire hole for wiring in the rear of bag on the side facing the tire, please drill out a hole using the 5/16 drill. This hole is to be used to run wires out of the bag lids.
-
Take the bottom speaker mounting plate and top speaker grill mounting plate and sandwich the bag lid so the bottom plate is on the inside of the bag lid and the top grill mounting plate is on the outer side of bag lid.(Figure A, Page 5)
-
Use the provided 4 screws and secure the two plates together, making them tight so no gaps can be seen on the outer grill bag lid plate and the bag lid itself.(Figure A, Page 5)
-
Speaker mounting- Place the 6×9 speaker in first, then the plastic 6×9 speaker cover from the bottom of the Speaker mounting plate. Using the 4 screws provided, secure both the 6×9 speaker and the plastic 6×9 speaker cover in place. Please make sure the speaker screws are tight but do not overtighten.
-
Attach speaker wires to speaker then run the wires and attach them to the source unit. Note to not run the wiring anywhere near, hot parts, fuel components, or moving parts.
-
Double-check all connections and all your screws to ensure they are secure before going out on your first audio adventure!
GET INVOLVED
WE ARE A COMMUNITY!
We read all product feedback, so please share your experience with us and with
others!
NEED SUPPORT?
Our U.S. based Customer Support Team is standing by to help you with your
inquiries.
CUSTOMER CARE: 805-751-4853 & Live Chat
ONLINE SUPPORT:
www.bossaudio.com/support
JOIN OUR COMMUNITY
Join our #BOSSlnsiders Program and have an impact on product updates &
releases. Apply at www.bossinsiders.com to
test and have an influence on future products.
Stay connected with the BOSS Audio Systems community plus get tips & tricks on
products and installs.
@BOSSAudioSystems
BEST WARRANTY IN THE INDUSTRY
Keep in Touch!
Register Your Product Online
https://bossaudio.com/product-registration-qr/
To register your product, scan this QR code with your smart device and fill in
the on line form. You can also find the online registration form at:
www.bossaudio.com/support
Your product may qualify for a FREE EXTENDED WARRANTY.
Please see www.bossaudio.com/policies
for the qualifications and details of this program.
THANK YOU
Welcome to the BOSS AUDIO SYSTEMS family.
Proud audiophi les since 1987.
BOSS Audio Systems
3451 Lunar Court• Oxnard, CA 93030
www.bossaudio.com
805-751-4853. Customer Service
Tech
Support:www.bossaudio.com/support
0820
Documents / Resources
| BOSS
AUDIO SYSTEMS BHD98 Harley Davidson Saddlebag Speaker
Kit
[pdf] User Manual
BHD98, BHD98 Harley Davidson Saddlebag Speaker Kit, Harley Davidson Saddlebag
Speaker Kit, Saddlebag Speaker Kit, Speaker Kit, Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>