Hangshi HB022 Bluetooth Folding Keyboard User Manual
- June 13, 2024
- Hangshi
Table of Contents
Hangshi HB022 Bluetooth Folding Keyboard
Package contents
- 1x Wireless Keyboard
- 1x Charging Cable
- 1x User Manual
Specification
- Bluetooth Version BT 5.1
- Dimensions 326.994.6211.32mm / 12.87×3.73×0.45 in
- Operating distance ＜8 m / 26.2 ft
- Rechargeable lithium battery 210mAh
- Uninterrupted Work Time 84 hours
- Stand-by Time 60 days
- Compatibility iOS,Android,Windows 8 or above
Indicators & definition
Power ON/OFF Keyboard
- Power On: Unfold the keyboard, ①②③ indicators will flash 3s then off.
- Power Off: Fold the keyboard.
Battery Power Display Indicator
- Press , flashing BLUE. (Every blinking represents 25% battery. That is to say, flashing once means the remaining battery is 25%; flashing twice, the remaining battery is 50%; flashing three times, 75%; flashing four times, 100%.)
Balance Stand Opening Steps
- Hidden balance stands: For keeping balance the keyboard while you are typing the marginal keys.
Pairing Steps
Pairing with 1st device
- Step 1. Unfold the keyboard, indicators will flash blue for 3s, then off.
- Step 2. Press Fn+Q to enter channel 1 mode.
- Step 3. Long Press Fn+Q for 3 seconds to enter pairing mode, BT1 indicator will flash blue and start to search the available Bluetooth device.
- Step 4. On your bluetooth device, find the Bluetooth name “Bluetooth 5.1 keyboard” and click to connect it.
- Step 5. The status indicator will be off after successfully paired.
Pair with 2nd device
- Step 1. Press “Fn+W” to enter channel 2 mode.
- Step 2. Long press “Fn+W” for 3 seconds to enter pairing mode, BT2 indicator will flash blue and start to search the available Bluetooth device.
- Step 3. Repeat the above pairing step 4 and step 5.
Pair with 3rd device
- Step 1. Press “Fn+E” to enter channel 3 mode.
- Step 2. Long press “Fn+E” for 3 seconds to enter pairing mode, BT3 indicator will flash blue and start to search the available Bluetooth device.
- Step 3. Repeat the above pairing step 4 and step 5.
Keys and Functions
Sleep Mode
The keyboard will enter sleep mode if idle for 30min. Press any key to exit
sleep mode.
Charging
-
Step 1. Connect one end of the included type-c cable to a USB charger, and connect the opposite end to the charging slot on the keyboard.
( Note: Output: DC 5 V / 500mA; USB charger is not included) -
Step 2. The charging indicator will glow red while the keyboard is charging. A full charge takes approximately 2 hours.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.