Razor 082-07-0066 A+ Kick Scooter with LED Light Owner’s Manual
- June 6, 2024
- Razor
Table of Contents
**Razor 082-07-0066 A+ Kick Scooter with LED Light Owner’s Manual
**
SAFETY WARNINGS
AN IMPORTANT MESSAGE TO PARENTS: This manual contains important information. For your child’s safety, it is your responsibility to review this information with your child and make sure that your child understands all warnings, cautions, instructions and safety topics. All children and preteens should ride with adult guidance at all times. Razor USA recommends that you periodically review and reinforce the information in this manual with younger riders, and that you are required to inspect and maintain your child’s scooter to ensure their safety.
GENERAL WARNING: Scooter riding can be a hazardous activity. Scooters can, and are intended to move and it is therefore possible to get into dangerous situations and/or lose control and/or fall. If such things occur you can be seriously injured or die. LIKE ANY OTHER MOVING PRODUCT, USING A SCOOTER CAN BE A DANGEROUS ACTIVITY AND MAY RESULT IN INJURY OR DEATH EVEN WHEN USED WITH PROPER SAFETY PRECAUTIONS. USE AT YOUR OWN RISK AND USE COMMON SENSE.
This manual contains many warnings and cautions concerning the consequences of failing to maintain, inspect or properly use your scooter. Because any incident can result in serious injury or even death, we do not repeat the warning of potential serious injury or death each time such a possibility is mentioned.
-
Do not allow children under age six (6) to use the scooter. These scooters are for children ages six (6) and above. Children under age eight (8) should ride with adult supervision at all times. All children and preteens should ride with adult guidance at all times.
-
Do not exceed 143 lb (65 kg) total weight on the A+ Lightshow scooter.
-
Rider weight does not necessarily mean a child’s size is appropriate to fit or maintain control of the scooter.
-
A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability to follow rules. -
Always wear safety equipment, such as helmet, knee pads and elbow pads. Always wear a helmet when riding your scooter and keep the chinstrap securely buckled.
-
Always wear closed toe shoes.
-
Ride on smooth, paved surfaces without loose debris, such as rocks or gravel, and away from motor vehicles.
-
Avoid sharp bumps, drainage grates, and sudden surface changes as
scooter may suddenly stop. -
Avoid streets and surfaces with water, mud, ice, sand, gravel, dirt, leaves
and other debris. Wet weather impairs traction, braking, and visibility. -
Do not ride at night or when visibility is impaired.
-
Brake will get hot from continuous use. Do not touch after braking.
-
Avoid excessive speed associated with downhill rides.
-
Adults must assist children in the initial assembly and/or adjustment procedures to fold/unfold scooter, and adjust handlebar and steering to height.
-
Obey all local traffic and scootering laws and regulations.
-
Watch out for pedestrians.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Direct parental supervision is required. Scooters are meant to be used only in controlled environments free of potential traffic hazards and not on public streets. Do not allow your child to ride a scooter in any areas where vehicle traffic is present. Child must maintain a hold on the handlebars at all times. Never allow more than one child at a time to ride a scooter. Never use near steps, sloped driveways, hills, roadways, alleys or swimming pool areas. Keep fingers and other body parts away from the product when folding or unfolding. Adults must not allow children to assist in assembling and/or folding or unfolding the scooter.
Do not ride a scooter in wet weather. Scooters are intended for use on solid, flat, clean and dry surfaces, such as pavement or level ground without loose debris, such as rocks or gravel. Wet, slick or uneven and rough surfaces may impair traction and contribute to possible accidents. Do not ride a scooter in mud, ice, puddles or water. Never risk damaging surfaces, such as carpet or flooring, by use of a scooter indoors.
PROPER RIDING ATTIRE
Always ensure child is wearing proper protective equipment, such as an approved safety helmet. A helmet may be legally required by local law or regulation in your area. A child should always wear shoes and keep shoelaces tied and out of the way of the wheels. Never ride barefooted or in sandals. Knee pads and elbow pads are recommended.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING.
Properly inspecting and maintaining your scooter can reduce the risk of
injury. Always inspect your scooter before riding and regularly maintain it.
Check and secure all fasteners before every ride. Replace worn or broken parts
immediately.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE.
Check local laws and regulations to see where and how you may use your Razor
scooter legally. In many states and local areas scooter riders are required BY
LAW to wear a helmet. Check local laws and regulations regarding laws
governing helmet use and scooter operation in your area.
WARNING: AAA BATTERIES
This product contains AAA batteries. A swallowed AAA battery can cause
internal chemical burns. Dispose of used batteries immediately. Keep new and
used batteries away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical
attention.
Batteries included for lights – adult attention for changing and disposal.
Batteries should only be replaced by an adult.
Loose batteries could present a choking hazard and should be kept away from small children.
Dispose of batteries properly.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS ATTENTION TO SAFE OPERATION. USE CAUTION.
BEFORE YOU BEGIN
Remove contents from box. Inspect the contents of the box for scratches and/or
dents that may have occurred during shipping. Because your scooter was
partially or fully assembled and packed at the factory, there should not be
any problems, even if the box has a few scars or dents.
WARNING:
DO NOT USE NON-RAZOR PRODUCTS WITH YOUR SCOOTER.Razor scooters have been built
to certain Razor design specifications. The original equipment supplied at the
time of sale was selected on the basis of its compatibility with the frame,
fork and all other parts. Certain aftermarket products may not be compatible
and will void the warranty.
Product ID Locations:
(See locations to the left)
- Side of Deck Plate
- Box – Side of UPC (Not Shown)
Box Contents:
- Scooter
- Owner’s Manual
ASSEMBLY AND SET-UP
Unfolding the Scooter for First Time Use
-
To release the folding mechanism, place the scooter on the ground, put one foot on the deck plate and push joint-release lever down. Raise T-bar up until it is securely locked in the upright position.
Note: The joint-release lever is spring-loaded and will automatically lock in the upright position when fully upright.
-
Insert and secure the left and right handlebars by pressing the spring-loaded buttons and inserting them into the T-bar.
-
Make certain BOTH handlebars are properly locked onto the T-bar.
WARNING: Keep fingers clear of the pivoting mechanism when folding or unfolding the scooter. Make sure others are standing clear.
WARNING: Failure to properly engage the spring-loaded buttons may cause the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly engaged the handlebars will not rotate nor will they move sideways. Note that when properly engaged, the springloaded buttons are clearly visible in the holes on the T-bar.
WARNING: Check hand grips and end caps regularly for wear or damage, as they are designed to aid in gripping handlebars and to provide some protection against possible impact. Replace immediately if worn, torn, damaged or missing.
Adjusting the Handlebar Height
- To adjust the height of the handlebars, open the quick-release lever and slide the T-bar to the desired position and resecure the quick-release lever to lock into place. When the T-bar is raised to the maximum height, depress the push button located directly below the quick-release lever to unlock the T-bar.
Note: The tension of the quickrelease lever can be adjusted by manually tightening or loosening the Allen bolt. Be careful not to overtighten. You should always be able to open and close the quick-release lever by hand and the T-bar should slide freely when the quick-release is open.
Collar Clamp
Required Tool: 5 mm Allen Wrench (not included)
Using a 5 mm Allen wrench, check that the collar clamp bolt(s) are tightened
securely. This item is tightened and quality inspected at the factory, but
there is a slight chance that the effects of shipping or handling may have
caused the bolt(s) to loosen.
Activating the Batteries
To activate the batteries, locate the battery compartment on the bottom of the deck and remove the plastic battery tab from under the battery cover. Please note that the battery tab may have been previously removed. If the battery tab is missing there is no cause for concern, as this will not affect the functionality of your scooter.
WARNING: Failure to properly secure the quick-release lever may cause the T-bar to telescope up or down while riding and may cause you to lose control and fall.
WARNING:
Failure to properly install and/ or tighten the collar clamp may cause the
rider to lose control and fall. If you are having difficulty understanding
these instructions, please contact Razor Customer Service for assistance.
PRE-RIDE CHECKLIST
Deck and Handlebars
Check for cracks or broken connections. Although broken decks are rare, it is
possible for an aggressive rider to run into a curb or object and wreck and
bend or break the deck. Get in the habit of inspecting your scooter on a
regular basis.
Hardware/Loose Parts
Check and secure all fasteners before every ride. Make sure the collar clamp,
quick-release lever, and handlebar spring buttons are locked properly in place
before riding. There should not be any unusual rattles or sounds from loose
parts or broken components. If the unit is damaged, do not ride. Reference
“Safety Warnings” on page 1 of this manual.
Safety Gear
Always wear proper protective gear, such as an approved safety helmet. Elbow
pads and kneepads are recommended. Always wear closed toe shoes (lace-up with
rubber soles) and keep shoelaces tied and out of the way of the wheels. NEVER
RIDE BAREFOOTED OR IN SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Be Careful!
You will see people on TV and maybe even people you know doing tricks and
stunts. These are people who have been practicing on scooters for a very long
time. Don’t try something until you are ready. Avoid steep inclines and don’t
ride too fast — you can lose control and fall. Skateboard parks are not
designed for scooters. Never ride in traffic or on the street and watch your
surroundings for pedestrians, bikers, boarders and skaters.
Maintain a hold on the handlebars at all times.
USAGE
How to Ride
Place one foot on the baseboard, push forward with the other foot. Steer with
both hands on the handlebars. For enhanced cornering, lean slightly into the
direction of the turn.
How to Operate Lights
- There is no power switch to active the lights on the deck or wheels.
- The deck lights are activated by a vibration sensor.
- Deck and wheel lights are activated when scooter is in motion.
- Deck lights will remain on for approximately 20 seconds after scooter has stopped moving. Lights are reactivated when scooter resumes motion.
How to Stop
For controlled stops, apply the brake by stepping on the rear-fender brake.
Razor recommends that you practice applying the brake at various speeds and in
an open area free from obstructions before riding your scooter around others.
REPAIR AND MAINTENANCE
Replacing Batteries
Required Tool: Phillips screwdriver (not included)
-
Using a Phillips screwdriver, remove the screw from the top of battery cover. DO NOT REMOVE THE OTHER TWO (2) SCREWS LOCATED ABOVE AND BELOW THE BATTERY COVER.
-
Remove the battery cover and set aside. Remove and discard the old batteries.
-
Insert the new AAA batteries and replace the cover and tighten the screw using a Phillips screwdriver.
Note: When installing the batteries, please pay attention to the
batteries’ positive and negative side which must align with the positive and
negative markings in the battery housing.
Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners
or solvents as they may damage the surfaces. Do not use alcohol, alcohol-based
or ammonia-based cleaners as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and wheel bearings are
maintenance free. Nonetheless, it is the responsibility of the owner or
guardian to periodically inspect the wheels for wear and tear, the axle for
proper tightness, and bearings for side-to-side play, and loose parts. When a
wheel or wheel bearing develops play, this is an indication of excess wear and
replacement is necessary. Replace immediately with only genuine Razor wheels.
Worn wheels/bearings are considered normal wear-and-tear and are not covered
by the Razor Warranty. Wheels other than genuine Razor wheels may not be
compatible with your Razor scooter. The use of anything other than genuine
Razor replacement parts may affect your safety and will void your warranty.
Replacement Parts
The most frequently requested replacement parts are available for purchase at
some Razor retail partners.
For the complete selection of replacement parts visit
www.razor.com
Repair Centers
For a list of authorized Razor repair centers:
- Check online at www.razor.com.
- Additional Customer Service contact information is listed at the back of this manual.
WARNING:
-
AAA batteries included for lights – adult attention for changing
and disposal. -
Batteries should only be replaced by an adult.
-
Loose batteries could present a choking hazard and should be kept away from small children.
-
Do not mix old and new batteries.
-
Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.
-
Dispose of batteries properly.
Note: Batteries are not covered under the Limited Warranty.
WARNING: Wheelies and other stunt-type riding reduces your ability to maneuver and control your scooter. Take the necessary precautions, such as wearing appropriate protective gear and practice in an area safe for stunt riding and free from obstructions.
WARRANTY
The manufacturer warranties this product to be free of manufacturing
defects for a period of 6 months from date of purchase. This Limited
Warranty does not cover normal wear and tear, or any damage, failure or
loss caused by improper assembly, maintenance, or storage.
This Limited Warranty will be void if the product is ever:
- used in a manner other than for recreation or transportation;
- modified in any way;
- rented.
The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual and write the serial number below.
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our website for product support, a list of authorized
service centers in the US and customer service contact information at
www.razor.com. Please have the product I.D. code
(located on the white label of your product) available for better assistance.
Additional Customer
Service contact information is listed below:
AMERICAS
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday – Friday
8:00 AM – 5:00 PM Pacific Time
customersupport@razorusa.com
EUROPE, MIDDLE EAST, AFRICA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
+44 (0) 120 267 2702
info@razoreu.com
ASIA
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+81 50 7579 6622
info@razor-asia.com
UNITED KINGDOM AND IRELAND
Razor USA LLC (UK)
Unit 20
Hartnoll Business Centre
Post Hill, Tiverton
Devon EX16 4NG
UK
+44 (0) 120 267 2702
info@razoreu.com
AUSTRALIA AND NEW ZEALAND
Razor USA LLC (AU and NZ)
P.O. Box 4280
Auburn South VIC 3122,
Australia
+1 800 954 354 (AU)
+0 800 003 221 (NZ)
info@razoranz.com
Copyright © 2003-2021 Razor USA LLC. All rights reserved. Razor®, the Razor logo design and the A® logo design are among the registeredtrademarks of Razor USA LLC and/or its affiliated companies in the United States and/or select foreign countries. A+ Lightshow logo design is a trademark of Razor USA LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>