UltraPro ZW4008 In-Wall Smart Switch Instruction Manual
- June 6, 2024
- UltraPro
Table of Contents
UltraPro ZW4008 In-Wall Smart Switch Instruction Manual
Thank you for your purchase!
1. FEATURES
- May be used in single-pole installation or with up to four add-on switches (model 39350) in 3-way or 4-way wiring configurations
- Auto line/load detection
- Blue LED indicates switch location in a dark room
- Screw terminal installation — requires wiring connections for line (hot), load, neutral and ground. Traveller wire required for 3-way or 4-way installation
- This Z-Wave device has advanced features that allow you to customize your experience. For a complete list of adjustable configurations, visit www.ezzwave.com
- A. Ground (Green/Bare)
- B. Line or Load (Black)
- C. Line or Load (Black)
- D. Traveller (Red/Other)
- E. Neutral (White)
- F. Top rocker — press to turn switch ON
- G. Bottom rocker — press to turn switch OFF
2. INSTALLATION
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture
at the service panel. All wiring connections must be made with the POWER OFF
to avoid personal injury and/or damage to the switch. This device is intended
for installation in accordance with the National Electric Code and local
regulations in the United States, or the Canadian Electrical Code and local
regulations in Canada. If you are unsure or uncomfortable about performing
this installation,
consult a qualified electrician.
MULTI-SWITCH WIRING
Add-on switch model 39350 is required for multi-switch installations. For more
information on multi-switch installations, refer to the add-on switch manual.
SINGLE-SWITCH WIRING
-
Shut power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing. -
Remove wall plate.
-
Remove the switch mounting screws.
-
Carefully remove the switch from the switch box. DO NOT disconnect the wires.
-
There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White Match these screw terminals to the wires connected to the existing switch. -
Disconnect the wires from the existing switch. Label wires according to the previous terminal connection.
OBSERVE IMPORTANT WIRING INFORMATION
IMPORTANT! This switch is rated for and intended to only be used with copper wire.
WIRE GAUGE REQUIREMENTS
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, neutral, ground and traveller connections. UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in)
WIRE STRIP LENGTH -
For attachment using the enclosure’s holes, strip insulation 5/8in. (16mm).
-
Connect the green or bare copper ground wire to the GROUND terminal (A).
-
Connect the black wire from the light to either LINE/LOAD terminal (B).
-
Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD terminal (C).
-
Connect the white wire to the neutral terminal (E) (use a jumper wire if needed). Insert wires into holes, do not wrap wires around screws.
- Insert switch into the switch box being careful not to pinch or crush wires.
- Switch must be independently mounted (vertical position only).
- Secure the switch to the box using the supplied screws.
-
Mount the wall plate.
-
Reapply power to the circuit at fuse box or circuit breaker and test the system.
MANUAL
CONTROL The front panel rocker switch allows the user to turn ON/OFF the
connected fixture.
- To turn the connected fixture ON, press and release the top of the rocker.
- To turn the connected fixture OFF, press and release the bottom of the rocker.
CYCLE LED LIGHT
The LED below the switch acts as a guide light or status indicator. How to
cycle through options: Press up three times and down once quickly.
- LED is ON when the load is OFF (guide light in the dark) (default).
- LED is ON when the load is ON (indicates the switch is ON).
- LED is always OFF.
- LED is always ON (illuminates switch in the dark).
3. CONNECTION
CONNECTING TO A Z-WAVE NETWORK
- Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
- Once the controller is ready to add your device, press and release the top or bottom of the smart switch (rocker).
If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product.
REMOVING AND RESETTING THE DEVICE
- Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
- Once the controller is ready to remove your device, press and release the top or bottom of the smart switch (rocker).
RETURNING SWITCH TO FACTORY DEFAULTS
Quickly press ON (top) button three times, then, immediately press the OFF
(bottom) button three times. The LED will flash ON/OFF five times when
completed successfully.
NOTE: This should only be used in the event your network’s primary
controller is missing or otherwise inoperable.
NOTE: Smart Start enabled products can be added into a Z-Wave network by
scanning the QR code on the product with a controller providing Smart Start
inclusion. No further action is required and the Smart Start product will be
added automatically within 10 minutes of being switched on in the network
vicinity.
OPTIONAL CUSTOMIZATION
CHANGING THE COLOR OF THE PADDLE
NOTE: Additional colours available on www.byjasco.com.
- Lift the air gap tab at the base of the paddle.
- Push side tabs in on one side and then the other to release paddle. Lift the cover up and off.
- Simply put the new paddle onto the switch by inserting the air gap and side tabs and snapping securely into place.
This device supports Association Command Class (3 Groups)
- Association Group 1 supports Lifeline, Binary Switch Report
- Association Group 2 supports Basic Set and is controlled by pressing the ON or OFF button with the local load
- Association Group 3 supports Basic Set and is controlled by double pressing the ON or OFF button
- Each Association Group supports 5 total nodes
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM 8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period.
SPECIFICATIONS – IMPORTANT!
ZW4008
Power: 120VAC, 60Hz
Signal (frequency): 908.4/916 MHz
Maximum loads: 960W incandescent, 1/2HP motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the
closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independently mounted (vertical position only), operating
control: type 1.c action,
pollution degree (2), rated impulse voltage (2500V), software class A For
indoor use only
Specifications subject to change without notice due to continuing product
improvement
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
FCC/IC – EN
This device complies with Part 15 of the FCC and Industry Canada license-
exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
Responsible Party – US Contact Information
FCC — U2ZZW4008 | IC: 6924A-ZW4008 Jasco Products Company | Model:
ZW4008/39348 10 E. Memorial Rd., Oklahoma City, OK 73114 |
1-800-654-8483 CAN ICES-3(B)/NMB-3(B)
WARNING
RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES
CAUTION:
- DO NOT EXCEED RATINGS
- DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
- DO NOT USE TO CONTROL RECEPTACLES
- FOR INDOOR USE ONLY
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE
ON/OFF STATUS OF MEDICAL AND LIFE-SUPPORT EQUIPMENT.
References
- amazon.com
- 39348 39354: UltraPro Z-Wave Smart Switch Installation and Operation - YouTube
- Product Registration
- Jasco
- Z-Wave by Jasco
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>