UltraPro ZWA3016 In Wall Smart Dimmer Instruction Manual

Z-Wave® certified
wireless lighting control 59350
59372
59373
ZWA3016

UltraPro ZWA3016 In Wall Smart Dimmer

Thank you for your purchase!
Instructions made easy
Read instructions or watch easy-tofollow video.

Scan code or visitbyjasco.com/59350i.

Register your product
Receive exclusive deals and register your product.

Scan code or visitbyjasco.com/deals.

For additional UltraPro products, visit our website www.byjasco.com.
Like our product?
Leave a review on your favorite retailer website or amazon.com.
Having problems?
Let us know how we can help.
Call 1-800-654-8483 between 7AM-8PM, M-F, Central Time.

ADDING YOUR DEVICE TO A Z-WAVE NETWORK

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the top or bottom of the rocker.

You have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller.
If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.
If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code.
Figure 1:

TO REMOVE AND RESET THE DEVICE

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the top or bottom of the rocker.

TO RETURN YOUR SWITCH TO FACTORY DEFAULTS

1. Pull up the air gap switch.
2. While pressing the OFF (bottom) button, push in the air gap and continue pressing the OFF button. The LED flashes through the eight colors once.

NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the device and lighting fixture at the service panel. All wiring connections must be made with the power OFF to avoid personal injury and damage to the device. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.

CHANGE PADDLE

This step is optional. Before installation, you may want to change the paddle to match your wallplate or décor.

1. Lift the air gap tab at the base of the paddle.
2. Push the side tabs in on one side followed by the other to release paddle and lift it from the device.
3. Insert the air gap and side tabs and snap the new paddle into place.

REMOVE SINGLE-POLE SWITCH

1. Shut off power to the circuit at the circuit breaker or fuse box.
   IMPORTANT! Verify power to switch box is OFF before continuing.

2. Remove wallplate.

3. Remove the switch mounting screws.

4. Carefully remove the switch from the switch box – DO NOT disconnect the wires.

5. Identify the following wires in the switch box:
   A. Ground – Green/bare
   B. Line (hot) – Black (connected to power)
   C. Load – Black (connected to lighting)
   D. Neutral – White

6. Disconnect the wires from the existing switch – label wires according to the previous terminal connections.

SINGLE-SWITCH WIRING

WIRING REQUIREMENTS
Attach using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 12lbf-in (14Kgf- cm).

1. Connect green/bare wire to the GROUND terminal.

2. Connect the black wire from the light to either LINE/LOAD terminal.

3. Connect the black wire from the power source (hot) to the other LINE/LOAD terminal.

4. Connect the white wire to the NEUTRAL terminal – use jumper if necessary.
   NOTE: The traveler terminal is only used for multi-switch wiring and is not used in a two-way system (one switch and one load).

5. Secure the device into the switch box with the provided mounting screws – ensure wires are not pinched or crushed.

6. Install the wallplate.

CYCLE LED

The LED below the dimmer acts as a guide light or status indicator.
How to cycle through options:

1. Press menu button for five seconds

2. Press up three times and down one time quickly – indicator flashes blue

3. Push the top paddle:
   A. Once for LED ON when the load is OFF – illuminates orange to confirm
   B. Twice for LED ON when the load is ON – illuminates yellow to confirm
   C. Three times for always OFF – illuminates pink to confirm
   D. Four times for always ON – illuminates purple to confirm

4. Press menu button once to save – indicator flashes green twice

CHANGE LED INDICATOR COLOR

The LED indicator color can be changed from the device.

1. Press menu button for five seconds

2. Press top paddle once and bottom paddle once – LED illuminates in selected color

3. Press top or bottom paddle to cycle through
   color options:
   • Red
   • Orange
   • Yellow
   • Green
   • Blue (default)
   • Pink
   • Purple
   • White

4. Press menu button once to save – indicator flashes green twice

Insert wires into holes, DO NOT wrap wires around screws
DO NOT remove screws

STANDARD 3-WAY SWITCH WIRING

IJMPORTANT! The Z-Wave device operates with add-on switches by default. To install it with a standard 3-way switch, follow the steps under 3-way configuration. The instructions below are for wiring a standard 3-way switch. See the add-on switch manual to install add-on switches.

LINE SIDE (Z-WAVE DEVICE)

1. Shut off power to the circuit at the circuit breaker or fuse box
2. Remove line side wallplate
3. Remove switch from line side switch box – DO NOT disconnect wires
4. Label wire from the power source LINE
5. Label one remaining wire traveler 1 – note the color of this wire for installation of the 3-way switch
6. Label the other remaining wire traveler 2
7. Disconnect all wires from the switch
8. Connect green/bare wire to the GROUND terminal
9. Connect the line wire to either LINE/LOAD terminal
10. Connect the traveler 1 wire to the other LINE/LOAD terminal
11. Connect the traveler 2 wire to the TRAVELER terminal
12. Connect one end of a jumper to the bundle of neutral wires using a wire nut
13. Connect the other end of the jumper to the NEUTRAL terminal
14. Secure the device into the switch box with the provided mounting screws – ensure wires are not pinched or crushed
15. Install the wallplate

OAD SIDE (3-WAY SWITCH)

1. Remove load side wallplate
2. Remove switch from load side switch box – DO NOT disconnect wires
3. Label wire from the light LOAD
4. Label traveler 1 wire – recall the wire color from the Z-Wave device installation
5. Label traveler 2 wire
6. Disconnect all wires from the switch
7. Connect green/bare wire to the GROUND terminal
8. Connect the load wire to the traveler 1 wire using a wire nut
9. Connect traveler 2 to the LINE (hot) terminal
10. Connect one end of a jumper to the bundle of neutral wires using a wire nut
11. Connect the other end of the jumper to the COMMON terminal
12. Secure the 3-way switch into the switch box – ensure wires are not pinched or crushed
13. Install the wallplate
14. Apply power to the fuse box or circuit breaker

https://byjasco.com/electrical-wiring-support/

SPECIFICATIONS — IMPORTANT!

ZWA3016
Voltage: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 360W or 3A CFL/LED
Operating temperature range: 32-104° F (0-40° C)
For indoor use only
Specifications subject to change without notice due to continuing product improvement

FEATURES

IMPORTANT! The fixture controlled by the Z-Wave in-wall smart dimmer must not exceed dimmer ratings. The dimmer is designed only for use with permanently installed fixtures.
Get to you know your Z-Wave smart dimmer

• Turn ON/OFF manually or remotely through the Z-Wave controller
• Can be added in multiple groups and scenes
• Auto-detect line/load terminals
• May be used in single-pole installation or 3-way wiring configurations
• Compatible with dimmable LED, CFL, incandescent and halogen lights
• Interchangeable paddle
• Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
• Multicolor LED indicates switch location in a dark room
• Screw terminal installation – requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way installation
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config

A. Ground (Green/bare)
B. Line or load (Black)
C. Line or load (Black)
D. Traveler (Red/other)
E. Neutral (White)
F. Top rocker — press & release to turn dimmer on, press & hold to increase brightness
G. Bottom rocker — press & release to turn dimmer off, press & hold to dim
H. Menu button
I. Air gap switch — pull the air gap switch out to disconnect the power.
Push it all the way back in for normal operation.

3-WAY CONFIGURATION

The smart device is set to work with add-on switches by default. To use with a standard 3-way switch, follow the steps below.

1. Pull out the air gap switch
2. While pressing the top paddle, push in the air gap switch
3. Continue pressing the top paddle until the LED flashes yellow three times to indicate standard 3-way switch configuration
4. Repeat these steps to return to the add-on switch setting – LED flashes blue three times

ADD-ON SWITCH COMPATIBLE
Enbrighten, UltraPro and JascoPro Series add-on switches support the same features as the Z-Wave device, such as single-, double- and triple-tap functions, from all locations. It also allows operation from up to five locations and provides a uniform appearance.
Visit byjasco.com to purchase add-on switches.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
This device supports association command class (3 Groups)

• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON or OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the ON or OFF button
• Each Association Group supports 5 total nodes

All brand names shown are trademarks of their respective owners
MADE IN MALAYSIA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 5-year limited warranty. Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 7AM-8PM, M-F, Central Time.
©JASCO 2022 | ZWA3016 | 59350, 59372, 59373 | 03/03/22 v2
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE, FLUORESCENT LIGHTING FIXTURE OR A TRANSFORMER-SUPPLIED APPLIANCE.

• ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE CFL/LED BULBS
• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
• FOR INDOOR USE ONLY

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM–8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period.

FCC/IC

Suppliers Declaration of Conformity
Model #: 59350, 59372, 59373 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

See product label for FCC/IC certification numbers.
CAN ICES-3(B)/NMB-3(B)

Z-Wave Configuration Capabilities

Z-Wave Command Class :

Z-Wave Command Class| Version| Controlled| Supported
---|---|---|---
COMMAND_CLASS_ZWAVEPLUS_INFO| 2| NO| YES
COMMAND_CLASS_APPLICATION_STATUS| 1| NO| YES
COMMAND_CLASS_ASSOCIATION| 2| NO| YES
COMMAND_CLASS_ASSOCIATION_GRP_INFO| 3| NO| YES
COMMAND_CLASS_MULTI-CHANNEL_ASSOCIATION| 3| NO| YES
COMMAND_CLASS_MANUFACTURER_SPECIFIC| 2| NO| YES
COMMAND_CLASS_POWERLEVEL| 1| NO| YES
COMMAND_CLASS_CONFIGURATION| 4| NO| YES
COMMAND_CLASS_FIRMWARE_UPDATE_META_DATA| 5| NO| YES
COMMAND_CLASS_INDICATOR| 3| NO| YES
COMMAND_CLASS_VERSION| 3| NO| YES
COMMAND_CLASS_BASIC| 2| YES| YES
COMMAND_CLASS_SWITCH_MULTILEVEL| 4| NO| YES
COMMAND_CLASS_SECURITY2| 1| NO| YES
COMMAND_CLASS_CENTRAL_SCENE| 3| NO| YES
COMMAND_CLASS_SUPERVISION| 1| NO| YES
COMMAND_CLASS_TRANSPORT_SERVICE| 2| NO| YES
COMMAND_CLASS_DEVICE_RESET_LOCALLY| 1| NO| YES

Note:
BASIC SET will map to SWITCH_MULTILEVEL_SET and their value will map the same .
Basic Report (Current Value, Duration) map to SWITCH_MULTILEVEL_REPORT (Value, Duration).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>