UltraPro 51398 2.4GHz Wi-Fi Smart Light Switch User Guide
- June 15, 2024
- UltraPro
Table of Contents
Ultra Pro 51398 2.4GHz Wi-Fi Smart Light Switch User Guide
Thank you for your purchase!
Instructions made easy
Read instructions or watch easy-tofollow video
Scan code or visit byjasco.com/51424iS
Register your product
Receive exclusive deals and register your product.
Scan code or visit byjasco.com/deals
For additional UltraPro products, visit our website, www.byjasco.com.
Like our product?
Leave a review on your favorite retailer website or amazon.com.
Having Problems?
Let us know how we can help.
Call 1-800-654-8483 between 7AM- 8PM, M-F, Central Time.
INSTALL THE APP
Remotely operate your smart switch with the easy-to-use UltraPro app. Follow the available instructions and resources to set up your smart device.
Download the app
Scan the QR code or search UltraPro on the Apple App Store or on Google Play
Scan the QR code or search UltraPro on the Apple App Store or on Google Play
Set up account
Create an account in the UltraPro app
Install the smart device
Wire the smart switch following the provided instructions
Add devices, control the smart switch from anywhere and create schedules
Voice control
Voice control works with Amazon Alexa or Google Assistant
NOTE: If the LED is not flashing, ensure the air gap switch is all the way to the left. Press the programming button for five seconds to reset the device and start the pairing process. If the LED is still not flashing, turn o power at the circuit breaker or fuse box, remove switch and check wire connections.
SPECIFICATIONS — IMPORTANT!
- WFD4002
- Voltage: 120VAC, 60Hz
- Incandescent: 960W
- Resistive: 1800W (15A)
- Motor: 1/2HP
- Operating Control Type 1.B Action
- Pollution Degree 2
- IP20
- Rated Impulse Voltage 2500V
- Software Class A
- Specifications subject to change without notice due to continuing product improvement
FEATURES
IMPORTANT! The fixture controlled by the Wi-Fi smart switch must not exceed switch ratings.
Get to you know your Wi-Fi smart switch
- Turn ON/OFF manually or through the UltraPro app
- Compatible with Amazon Alexa and Google Home
- Auto-detect line/load terminals
- May be used in single-pole installation or 3-way wiring configurations
- Compatible with all LED, CFL, incandescent and halogen lights
- Uses a standard, toggle wallplate for single-gang installations (wallplate not included)
- Screw terminal installation – requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way installation
A. Ground (green/bare)
B. Line or load (black)
C. Line or load (black)
D. Traveler (red/other)
E. Neutral (white)
F. Up — press & release to turn switch ON
G. Down — press & release to turn switch OFF
H. Programming button — press for five seconds to enter pairing mode or
restore factory settings
I. Air gap switch — slide the air gap switch right to disconnect the
power. Move it to the left for normal operation.
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the power OFF to avoid personal injury and damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.
REMOVE SINGLE-POLE SWITCH
-
Shut off power to the circuit at the circuit breaker or fuse box
IMPORTANT! Verify power to switch box is OFF before continuing -
Remove wallplate
-
Remove the switch mounting screws
-
Carefully remove the switch from the switch box – DO NOT disconnect the wires
-
Identify the following wires in the switch box:
A. Ground – Green/bare
B. Line (hot) – Black (connected to power)
C. Load – Black (connected to lighting)
D. Neutral – White -
Disconnect the wires from the existing switch – label wires according to the previous terminal connections
SINGLE-SWITCH WIRING
WIRING REQUIREMENTS
Attach using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 12lbf-in (14Kgf-cm).
-
Connect green/bare wire to the GROUND terminal
-
Connect the black wire from the light to either LINE/LOAD terminal
-
Connect the black wire from the power source (hot) to the other LINE/LOAD terminal
-
Connect the white wire to the NEUTRAL terminal – use jumper if necessary
NOTE: The traveler terminal is only used for multi-switch wiring and is not used in a two way system (one switch and one load) -
Secure the Wi-Fi switch into the switch box with the provided mounting screws – ensure wires are not pinched or crushed
-
Install the wallplate
-
The blue LED backlight flashes twice per second for up to 10 minutes to indicate the device is in pairing mode
Insert wires into holes,
DO NOT wrap wires around screws
DO NOT remove screws
3-WAY SWITCH WIRING
The smart device supports standard 3-way switches for ON/OFF control and Enbrighten, UltraPro or JascoPro Series add-on switches for full smart functions from all locations. Below are instructions for installing a standard 3-way switch. See the add-on switch manual for add-on switch installation instructions.
Typical wiring schematic for 3-way installation
Line side (hot)
Load side
Wi-Fi switch on line side with standard 3-way switch
A. LINE – Black wire/black screw
B. TRAVELER 1 – Black wire/black screw (output)
C. TRAVELER 2 – Red wire/brass screw (traveler)
D. GROUND – Green or bare wire/green screw
E. JUMPER – White wire/silver screw
Scan QR code below if there isn’t a line bundle in the switch box
LINE SIDE (WI-FI SWITCH)
- Shut off power to the circuit at the circuit breaker or fuse box
- Remove line side wallplate
- Remove switch from line side switch box – DO NOT disconnect wires
- Label wire from the power source LINE
- Label one remaining wire traveler 1 – note the color of this wire for installation of the 3-way switch
- Label the other remaining wire traveler 2
- Disconnect all wires from the switch
- Connect green/bare wire to the GROUND terminal
- Connect the line wire to either LINE/LOAD terminal
- Connect the traveler 1 wire to the other LINE/LOAD terminal
- Connect the traveler 2 wire to the TRAVELER terminal
- Connect one end of a jumper to the bundle of neutral wires using a wire nut
- Connect the other end of the jumper to the NEUTRAL terminal
- Secure the Wi-Fi switch into the switch box with the provided mounting screws – ensure wires are not pinched or crushed
- Install the wallplate
- The blue LED backlight flashes twice per second for up to 10 minutes to indicate the device is in pairing mode
LOAD SIDE (3-WAY SWITCH)
- Remove load side wallplate
- Remove switch from load side switch box – DO NOT disconnect wires
- Label wire from the light LOAD
- Label traveler 1 wire – recall the wire color from the Wi-Fi switch installation
- Label traveler 2 wire
- Disconnect all wires from the switch
- Connect green/bare wire to the GROUND terminal
- Connect the load wire to the traveler 1 wire using a wire nut
- Connect traveler 2 to the LINE (hot) terminal
- Connect one end of a jumper to the bundle of line wires using a wire nut
- Connect the other end of the jumper to the COMMON terminal
- Secure the 3-way switch into the switch box – ensure wires are not pinched or crushed
- Install the wallplate
- Apply power to the fuse box or circuit breaker
Scan code for alternate 3-way wiring process
ADD-ON SWITCH COMPATIBLE
UltraPro, Enbrighten and JascoPro Series add-on switches support the same features as the Wi-Fi device, such as single-, double- and triple-tap functions, from all switch locations. It also allows operation from up to five locations and provides a uniform appearance.
Visit byjasco.com to purchase add-on switches.
WI-FI ADD-ON SWITCH CONFIGURATION
Wi-Fi devices set to operate with standard 3-way switches by default. If installing this add-on switch with a Wi-Fi device, 3-way configuration must be changed in the app.
- Open the device screen in the app
- Tap “settings”
- Press “3-way configuration”
- Select “add-on switch”
- Press “confirm”
For product patent information, visit ww.byjasco.com/patents.
All brand names shown are trademarks of their respective owners
App Store is a service mark of Apple Inc. Google and Google Play are
trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks
of Amazon.com, Inc. or its aliates.
MADE IN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City,
OK 73114.
This Jasco product comes with a 5-year limited warranty. Visit
www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483, M-F, 7AM-8PM Central
Time. ©JASCO 2023 | WFD4002 | 51424, 51439, 51440 | 06/09/23 v2
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>