UltraPro 60837 Escape Color-Changing Flex Light User Guide

UltraPro 60837 Escape Color-Changing Flex Light

Quick Start Guide

Congratulations on your new UltraPro Escape Color-Changing Flex Light! This product is designed to provide your space with high-quality lighting. Combine with additional UltraPro Escape Flex Lights to form one continuous string up to 120ft. in length!
IMPORTANT: Before installation, please read all the warning statements included at the bottom of these instructions. Save these instructions for later use.

SETUP

1. Carefully unpack the flex light from the box and remove the binding tape.
2. Before installing, plug the light into an outlet to ensure it works properly. Remove the plastic pull tab on the remote to test IR remote features. Be sure to unplug the light after testing it.

INSTALLATION

Select a mounting location that is capable of supporting the flex light and close enough for the power cord to easily reach an outlet. All screws and mounting clips are included.

1. Mount the power supply using the keyhole tab and screws
2. Mark the locations for each mounting clip with a pencil. Then, drill a pilot hole on each pencil marking using a 1/16in. drill bit.
3. Attach each mounting clip using the included screws.
4. Fit the flex light into each installed mounting clip.
5. Plug the power cord into a 120VAC 60Hz outlet. (GFCI outlet if installing outdoors.)

INSTALLING ADDITIONAL FLEX LIGHTS

1. Unscrew the end cap on the first flex light and slide the compression nut backwards to expose the receptacle.
2. Insert the connector from the next flex light into the receptacle. Then, slide the compression nut forward over the new connection point and screw it securely into place.

REMOVING THE FLEX LIGHT

1. Always unplug from power prior to uninstalling.
2. Carefully remove the flex light from the mounting hardware without tugging or pulling.
3. Store lights in a dry location.

IMPORTANT: This product employs fuse overload and short-circuit protection. If the fuse blows, unplug the product from the outlet and unplug any other products connected to the product. Replace the fuse following these instructions and refer to product marking for the proper fuse rating.

1. Unplug from power. Do not unplug by pulling on cord.
2. Slide open the fuse access cover on top of the plug towards blades.
3. Carefully remove fuse by pushing from the other side.
4. RISK OF FIRE. Replace fuse only with 8 Amp, 125 Volt fuse (provided with product).
5. Close fuse cover.
6. RISK OF FIRE. Do not replace the plug as it contains a safety device (fuse) that should not be removed. If damaged, discard product.

OPERATION

• Single Color Press your favorite single-color button to set the entire flex light to that color.
• Fade The flex light will slowly fade through each color.
• Strobe Each color will strobe from one to the next.
• Pulse The intensity of each color will slowly increase and decrease.
• Flash The light will blink ON and OFF through each color.

WARNING

1. DO NOT MOUNT OR SUPPORT FLEXIBLE LIGHT IN A MANNER THAT CAN
2. DAMAGE THE OUTER JACKET OR CORD INSULATION.
3. RISK OF FIRE AND ELECTRIC SHOCK. UNCOIL FLEXIBLE LIGHT PRIOR TO PLUGGING IN. DO NOT USE WITH EXTENSION CORD NEAR WATER OR WHERE WATER MAY ACCUMLATE. FOR USE ONLY ON GFCI PROTECTED CIRCUITS. DO NOT SUBMERGE.
4. MATERIAL MAY BECOME BRITTLE WHEN COLD. DO NOT INSTALL WHERE IT MAY BE STEPPED ON OR SUBJECT TO PHYSICAL DAMAGE.
5. DO NOT INSTALL NEAR FLAMMABLE LIQUIDS.
6. DO NOT INSTALL CLOSER THAN 3 METERS FROM A SWIMMING POOL SURFACE.
7. ALWAYS UNPLUG THIS PRODUCT BEFORE INSTALLING OR REPLACING FUSES. USE ONLY 125-VOLT, 8 AMP MAX.
8. DO NOT COVER FLEXIBLE LIGHT AS THE COVERING MAY CAUSE THE FLEXIBLE LIGHT TO OVERHEAT AND MELT OR IGNITE.
9. TO PREVENT OVERHEATING, DO NOT ALLOW CONTACT BETWEEN FLEXIBLE LIGHT CABLES OR PARTS OF THE FLEXIBLE LIGHT CABLE. MAINTAIN AT LEASE 12MM (0.47IN) SPACING BETWEEN LIGHT CABLE OR LIGHT CABLE PARTS.
10. NOT SUITABLE FOR FIELD CUTTING OR SPLICING.
11.  DO NOT OVERLOAD. THIS PRODUCT’S LENGTH IS 24 FEET. DO NOT CONNECT TOGETHER MORE THAN 120 TOTALFEET.

FCC STATEMENT

SUPPLIERS DECLARATION OF CONFORMITY | MODEL #: 56360 | JASCO PRODUCTS CO.,10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114, WWW.BYJASCO.COM. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES: —REORIENT OR RELOCATE THE RECEIVING ANTENNA. —INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER. —CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED. —CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP

References

• . Spend less. Smile more.
• 60837: UltraPro Color Changing Flex Light Operation - YouTube
• Product Registration
• LED Lighting
• Recycling Matters at Jasco
• Jasco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>