ultraPro 54504 LED Rope Lights User Manual

54504 LED Rope Lights

LED Rope Light
User Manual

Congratulations on your new UltraPro Escape LED Rope Light! Please read this user manual carefully before using the product. Important features and operating procedures are included in this guide. Please keep the manual in a safe place for future reference.
IMPORTANT: Before installation, please read all the warning statements included at the bottom of these instructions. Save these instructions for later use.

INSTALLATION

INCLUDED HARDWARE

TOOLS REQUIRED

MOUNTING THE ROPE LIGHT
Before installing, make sure that the surface can support the rope light and that the power cord will be in range of an outlet.

1. Mark the location for each clip (B) and drill pilot holes using a 1/16in. drill bit.
2. Place the mounting clips over the pilot holes and use a screwdriver to install and tighten each screw (C).
3. Carefully affix the rope light (A) to each installed clip.
4. Insert the power plug into outlet.

LINKING ADDITIONAL ROPE LIGHTS

IMPORTANT: Disconnect the rope light from power before linking any additional strands. You can link up to three strands together in a sequence (maximum 150 ft.).

1. Unscrew and remove the end plug (A) to expose the female connector (B).
2. Make sure the ring gasket (C) is in place on the female connector.
3. Plug male connector (D) from next segment into the female connector. Screw compression nut (E) over connection until tight.

FUSE REPLACEMENT

This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.

1. Grasp plug (1) and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. Always unplug this product before installing or replacing fuses.
2. Slide open the fuse access cover (2) on top of the attachment plug towards blades (3).
3. Remove fuse (4) carefully. Push the fuse from the other side.
4. Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
5. Close fuse cover (2). Close the fuse access cover on top of attachment plug.
6. Risk of fire. Do not replace attachment plug as it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

WARNING

1. DO NOT MOUNT OR SUPPORT FLEXIBLE LIGHT IN A MANNER THAT CAN DAMAGE THE OUTER JACKER OR CORD INSULATION.
2. RISK OF FIRE AND ELECTRIC SHOCK. UNCOIL FLEXIBLE LIGHT PRIOR TO PLUGGING IN. DO NOT USE WITH EXTENSION CORD NEAR WATER MAY ACCUMLATE. FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
3. MATERIAL MAY BECOME BRITTLE WHEN COLD. DO NOT INSTALL WHERE IT MAY BE STEPPED ON OR SUBJECT TO PHYSICAL DAMAGE.
4. DO NOT INSTALL NEAR FLAMMABLE LIQUIDS.
5. DO NOT INSTALL CLOSER THAN 3 METERS FROM A SWIMMING POOL SURFACE.
6. ALWAYS UNPLUG THIS PRODUCT BEFORE INSTALLING OR REPLACING FUSES. USE ONLY 125-VOLT, 3 AMP MAX.
7. DO NOT COVER FLEXIBLE LIGHT AS THE COVERING MAY CAUSE THE FLEXIBLE LIGHT TO OVERHEAT AND MELT OR IGNITE.
8. TO PREVENT OVERHEATING, DO NOT ALLOW CONTACT BETWEEN  FLEXIBLE LIGHT CABLES OR PARTS OF THE FLEXIBLE LIGHT CABLE. MAINTAIN AT LEASE 10MM (0.39IN) SPACING BETWEEN LIGHT CABLE OR LIGHT CABLE PARTS.
9. NOT SUITABLE FOR FIELD CUTTING OR SPLICING.
10. DO NOT OVERLOAD. DO NOT CONNECT TOGETHER MORE THAN 150 TOTAL FEET.

MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty. Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at1-800-654-8483 between 7AM—8PM , M-F,
Central Time.

©JASCO 2020 | 54503, 54504, 54505, 54842,
54843, 54586 | 3/23 v2reciclable
**100% recyclable Separate label from  oy-Nel ehex=before aa cel lays byjasco.com/recycle
Thank you for your purchase!
Instructions made easy**
Read instructions or watch easy-to- follow video.

https://byjasco.com/54503i

Scan code or visit byjasco.com/54503i
Register your product Receive exclusive deals and register your product.

Scan code or visit byjasco.com/deals

Discover more innovative lightining at byjasco.com/lighting|
Like our product?
Leave a review on your favorite retailer website or amazon.com.
Having Problems?
Let us know how we can help. Call 1-800-654-8483 between
7AM-8PM, M-F, Central Time.

References

• . Spend less. Smile more.
• YouTube
• YouTube
• Product Registration
• LED Lighting
• Recycling Matters at Jasco
• Jasco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>