UltraPro 59033 Add-an-outlet Light Adapter User Manual
- June 6, 2024
- UltraPro
Table of Contents
UltraPro 59033 Add-an-outlet Light Adapter
Thank you for your purchase!
Instructions made easy
Read instructions or watch the easy-to-follow videos. Scan code or visit byjasco.com/59033i
Exclusive deals
For deals, to register your purchase and to tell us how we’re doing, simply scan the code or visit byjasco.com/deals
For a full line of lighting products, search “UltraPro” on Amazon.com or visit byjasco.com/ultrapro.
Like our product? Leave a review on amazon.com
Having problems? Let us know how we can help. 1-800-654-8483 between 7 AM-8 PM, M-F, Central Time.
SETTING UP
Before installing your UltraPro light adapter, it is important to read the entire manual, all safety instructions, and ensure all parts are present. Save this user manual for later use.
INSIDE THE BOX
- A, B, C. Mounting bracket screws
- D. Mounting bracket
- E. Gasket
- F. Mounting bolt
- G. Mounting plate/cover screws (pre-installed)
- H. Rubber screw hole plugs
- I. Light adapter with mounting plate
- J. Light adapter cover (optional) K, L. Light fixture screws (optional)
TOOLS NEEDED
INSTALLATION
Follow these steps to properly install your light adapter to the junction box. After the adapter is installed, follow Option 1: Add a Light Fixture or Option 2: Using without a Light Fixture. Be sure power is OFF before proceeding.
Step 1: Install Mounting Bracket Hold the mounting bracket (D) to the junction box with the “front side” facing you. Use the appropriately sized screws (A, B or C) to securely attach the bracket to the junction box.
Step 2: Route and Connect Wiring Hold the light adapter over the now- installed mounting bracket. If the mounting bracket blocks the light adapter house hot, neutral, and ground wires (with push-in connects), carefully move them to the other hole. DO NOT attach the light adapter to the bracket yet. Route the house hot, neutral, and ground wires through the gasket (E).
Use the wire strippers to strip the house AC power supply wires to expose 3/8in. (9.5mm) of wire.
WARNING: BE SURE POWER IS OFF BEFORE WIRING
Push your home AC power supply wires into the wire connectors with matching colors (black – “House Hot”, white – “House Neutral”, green/yellow – “House Ground”). Neatly arrange the wires so that they do not stick outside of the junction box.
Step 3: Install Light Adapter
- Position the light adapter (I) and gasket (E) over the mounting bracket (D).
- Insert the mounting bolt (F) through the center hole in the back of the light adapter and through the gasket before threading it into the mounting bracket. Tighten the mounting bolt with a Phillips-head screwdriver. DO NOT overtighten.
- Insert four rubber plugs (H) in mounting plate/cover screw holes.
NOTE: Optionally, it may be easier to connect the mounting bolt by removing the mounting plate.
Step 4: Waterproofing Apply weatherproof exterior caulk sealant to any gaps behind the light adapter, junction box and mounting surface to prevent any water leakage into the product.
OPTION 1: Adding a Light Fixture You can use the pre-installed mounting plate on your light adapter (I) to mount a separately purchased light fixture. It provides a mounting interface of a standard 4in. round electrical junction box supports weight up to 50lbs and a maximum 600W electrical load.
Ensure power is OFF. For light fixtures greater than 25lbs, secure a light adapter with screws to two outer mounting tabs. Follow the instructions for the light fixture you wish to connect to the mounting plate. For electrical connections, use the wires from the light adapter labeled “Light Load”, “Light Neutral” and “Light Ground”.
NOTE: If needed, you can use the light fixture screws (K, L) to secure your light fixture to the mounting plate.
OPTION 2: Using Without Light Fixture If you are only using the GFCI outlet feature of the light adapter, follow these instructions to mount the cover.
- Ensure power is OFF.
- Remove the four rubber plugs (H) from the mounting plate.
- Unscrew the four screws and remove the mounting plate. The screws will not fall out.
- Arrange all wiring inside the light adapter.
- Install the cover (J), ensuring the plastic tab is facing the GFCI outlets, and tighten pre-installed screws to secure the cover.
- Replace the four rubber plugs (H) in the mounting plate.
OPERATION
- The GFCI outlets are ALWAYS ON and are not controlled by the switch.
- The ON/OFF switch controls power to a connected light fixture.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product.
This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM–8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.
SPECIFICATIONS
- Model #: ES26WF-GP
- Input Power Requirements: 120VAC, 60Hz
- GFCI Outlets: 15A, 1800W, 120VAC
- Connected Light Max Load: 600W, 5A MAXIMUM ELECTRICAL LOAD Connected Light Max Weight: 50 LBS
CARE AND CLEANING
- DO NOT spray the light fixture with a hose or power washer.
- DO NOT use paints, solvents, or other chemicals on this light fixture.
- To prolong the original appearance, clean only with clean water and a soft, damp cloth.
SAFETY INSTRUCTIONS
WARNINGS TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE OR INJURY:
- Read all SAFETY INSTRUCTIONS and USER MANUAL before attempting to install or operate.
- Install in accordance with all local and national electrical codes. Consult a local licensed electrician or electrical contractor if you are not sure about the installation.
- For use only in a circuit protected by a fuse or circuit breaker.
- Must be properly grounded.
- DO NOT ATTEMPT TO INSTALL A FIXTURE WITH THE POWER ON. Ensure electricity is TURNED OFF at the main circuit breaker or fuse box. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the fixture. Verify power is OFF at the junction box using AC voltage tester before installation.
- Double-check all connections to be sure they are tight and correct and no wires are pinched.
- Account for small parts and destroy packaging material, as these may be hazardous to children.
- If installed OUTDOORS, mount to a WATERPROOF surface mount or recessed electrical junction box with a 120VAC power source. Seal all gaps behind mounting plate with waterproof caulk.
- NOTICE: DO NOT connect the product to a dimmer switch or timer.
- Wear well-fitted safety glasses during the entire installation procedure.
- DO NOT EXCEED ELECTRICAL RATINGS.
- DO NOT exceed 50lb connected light fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>