UltraPro 60843 Escape White Flex Light User Guide

: June 6, 2024
: UltraPro

Table of Contents

UltraPro 60843 Escape White Flex Light
Quick Start Guide
SETUP
INSTALLATION
INSTALLING ADDITIONAL FLEX LIGHTS
REMOVING THE FLEX LIGHT
WARNING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

UltraPro 60843 Escape White Flex Light

Quick Start Guide

Congratulations on your new UltraPro Escape White Flex Light! This product is designed to provide your space with high-quality lighting. Combine with additional UltraPro Escape Flex Lights to form one continuous string up to 144ft. in length!
IMPORTANT: Before installation, please read all the warning statements included at the bottom of these instructions. Save these instructions for later use.

SETUP

Carefully unpack the flex light from the box and remove the binding tape.
Before installing, plug the light into an outlet to ensure it works properly. Be sure to unplug the light after testing it.

INSTALLATION

Select a mounting location that is capable of supporting the flex light and close enough for the power cord to easily reach an outlet. All screws and mounting clips are included.

Mark the locations for each mounting clip with a pencil. Then, drill a pilot hole on each pencil marking using a 1/16in.drill bit.
Attach each mounting clip using the included screws.
Fit the flex light into each installed mounting clip.
Plug the power cord into a 120VAC 60Hz outlet.(GFCI outlet if installing outdoors.)

INSTALLING ADDITIONAL FLEX LIGHTS

Unscrew the end cap on the first flex light and slide the compression nut backwards to expose the receptacle.
Insert the connector from the next flex light into the receptacle. Then, slide the compression nut forward over the new connection point and screw it securely into place.

REMOVING THE FLEX LIGHT

Always unplug from power prior to uninstalling.
Carefully remove the flex light from the mounting hardware without tugging or pulling.
Store lights in a dry location.

IMPORTANT: This product employs fuse overload and short-circuits protection. If the fuse blows, unplug the product from the outlet and unplug any other products connected to the product. Replace the fuse following these instructions and refer to the product marking for the proper fuse rating.

Unplug from power. Do not unplug by pulling on the cord.
Slide open the fuse access cover on top of the plug towards blades.
Carefully remove fuse by pushing from the other side.
RISK OF FIRE. Replace fuse only with 8 Amp, 125 Volt fuse (provided with product).
Close fuse cover.
RISK OF FIRE. Do not replace the plug as it contains a safety device (fuse) that should not be removed. If damaged, discard the product.
Supply Power| 120VAC 60 Hz
---|---
Electrical Ratings:| 28.8 Watts, 0.24A
Length| 24ft
Maximum Length| Linkable up to 144ft
Light Color (CCT)| 2700K
Fuse| 8A,125V

WARNING

DO NOT MOUNT OR SUPPORT FLEXIBLE LIGHT IN A MANNER THAT CAN DAMAGETHE OUTER JACKET OR CORD INSULATION.
RISK OF FIRE AND ELECTRIC SHOCK. UNCOIL FLEXIBLE LIGHT PRIOR TO PLUGGING IN. DO NOT USE WITH EXTENSION CORD NEAR WATER OR WHERE WATER MAY ACCUMLATE. DO NOT SUBMERGE. FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
MATERIAL MAY BECOME BRITTLE WHEN COLD. DO NOT INSTALL WHERE IT MAY BE STEPPED ON OR SUBJECT TO PHYSICAL DAMAGE.
DO NOT INSTALL NEAR FLAMMABLE LIQUIDS.
DO NOT INSTALL CLOSER THAN 3 METERS FROM A SWIMMING POOL SURFACE.
ALWAYS UNPLUG THIS PRODUCT BEFORE INSTALLING OR REPLACING FUSES. USE ONLY 125-VOLT,
AMP MAX.
DO NOT COVER FLEXIBLE LIGHT AS THE COVERING MAY CAUSE THE FLEXIBLE LIGHT TO OVERHEAT AND MELT OR IGNITE.
TO PREVENT OVERHEATING, DO NOT ALLOW CONTACT BETWEEN FLEXIBLE LIGHT CABLES OR PARTS OF THE FLEXIBLE LIGHT CABLE. MAINTAIN AT LEAST 12MM (0.47IN) SPACING BETWEEN LIGHT CABLE OR LIGHT CABLE PARTS.
NOT SUITABLE FOR FIELD CUTTING OR SPLICING.
DO NOT OVERLOAD. THIS PRODUCT’S LENGTH IS 24 FEET. DO NOT CONNECT TOGETHER MORE THAN 144 TOAL FEET.