Woodpeckers REV012722 Multi Router Micro Adjust Owner’s Manual

Woodpeckers REV012722 Multi Router Micro Adjust

Specifications

• Product Name: MULTI-ROUTERDCBA MICRO ADJUST
• Manufacturer: Woodpeckers, LLC
• Location: Strongsville, Ohio
• Website: woodpeck.com

Product Usage Instructions:
Installing the Swing Arm Micro Adjust for the MULTI-ROUTER

1. Move the Vertical Slide of the Multi-Router to the top of travel.
2. Loosen the Set Screws securing the Shaft to the Upright using a 1/8 Allen key.
3. Ensure Vertical Slide Lock, any Stop Collars, and old Micro Adjust are not tightened.
4. Slide the Shaft upwards and out of the Vertical Slide Bearings.
5. Remove the old Micro Adjust, if present, and install the new Micro Adjust (with Swing Arm).
6. Re-tighten the Set Screws securing the Shaft.

Using Micro Adjust

1. Swing the Micro Adjust forward over the Vertical Table.
2. Loosen the Knob on the Shaft Collar to adjust the position on the Shaft.
3. Adjust the Vertical Table using the Brass Thumb Screw and Scale for precise positioning.
4.  Locate and use Stop Collars for repeatable stops on the vertical slide.

FAQ:
Q: Where can I find the most current version of the instruction manual?
A: The latest manuals are available for download/print on woodpeck.com via the tool’s page under Additional Information or Instructions tabs.

MULTI-ROUTER MICRO ADJUST OWNER’S MANUAL

If you think you’re missing anything, email us at mailroom@woodpeck.com You can also call us at 800-752-0725 from 9:00 a.m. to 4:00 p.m. EST Monday – Friday.

At Woodpeckers we are constantly revlewing & improving our toots. The most current version of our instruction manuals are always available to download/print at woodpeck.com via the tool’s page. (Located in the bottom section of the toot page under the “Additional Information” or “Instructions” abs.)
Be the first to know all the new products & sales by subscribing to our Club. (Located at the top center of our webpage woodpeck.com)
Subscribe to our YouTube channel to stay up-to-date on all the latest tool tips & tricks. Interact with us! Follow us on Facebook & Instagram!

WARNING!
This product can expose you to chemicals, including chromium, which is known to the State of California lo cause cancer and birth defects or other reproductive ham. For more information go to www.P65Wamings.ca.gov

DIAGRAM NUMBER

PART NAME

1. Vertical Casting, Upper Shaft Support
2. Micro Adjust (with Swing Arm)
3. Stop Collar
4. Vertical Slide Bearings
5.  Vertical Casting, Lower Shaft Support
6. set Screw
7. Shaft
8. Vertical Slide Lock

INSTALLING THE SWING ARM MICRO ADJUST FOR THE MULTI-ROUTER

1. Move the Vertical Slide of the Multi-Router to the top of the travel.
2. Loosen the Set Screws securing the Shaft to the Upright, using a 1/8″ Allen key. NOTE: The Vertical Slide should remain “up” due to the Gas Spring on the other Shaft.
3. Ensure that the Vertical Slide Lock, any Stop Collars ® and old Micro Adjust ®(if present) are not tightened.
4. Slide the Shaft upwards and out of the Vertical Slide Bearings. The Stop Collars * will now be free as well.
5. Remove the old Micro Adjust (if present) and locate the new, pre-assembled, Micro Adjust (with Swing Arm) ,
6. Slide the Shaft  back through in the following order:
7.  Vertical Casting, Upper Shaft Support
8. Micro-Adjust (with Swing Arm)
9.  One of the Stop Collars
10. Vertical Slide Bearings
11.  The other Stop Collar
12.  Vertical Casting, Lower Shaft Support
13. Re-tighten the Set Screws 6 securing the Shaft 7, using a 1/8″ Allen Key.
    

USING MICRO ADJUST

The Micro Adjust can rotate out of the way when not in use.

1. Swing the Micro Adjust forward so that the Brass Thumb Screw is over top of the Vertical Table. FIGURE 1.
2. Loosen the Knob on the Shaft Collar of the Micro Adjust so that the whole thing can slide up and down the Shaft. Lower it until the Brass Thumb Screw comes in contact with the Vertical Table. Tighten the Knob.
3. With the Aluminum Thumb Nut loose, make adjustments to the Brass Thumb Screw to raise or lower the Vertical Table, reading the Scale (or optional digital readout) to the desired location.
4. You can now locate either the top or bottom Stop Collar (depending on what end of the feature you are dialing in) for the vertical slide. The Stop Collars work best as repeatable stops, though the Micro Adjust can be used as a stop for the “up” direction.

TO STOW THE MICRO ADJUST

1. Loosen the Knob on the Micro Adjust clamping collar, slide towards the top of the shaft, then re-tighten the Knob.
2. Swing the Micro Adjust towards the center of the machine until the swing arm contacts the vertical casting. FIGURE 2.
   

References

• Woodworking Tools Designed and Made in USA | Woodpeckers
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>