CLAYPAKY CD3000 330W Hybrid Discharge Moving Head Beam Instruction Manual
- June 6, 2024
- CLAYPAKY
Table of Contents
CLAYPAKY CD3000 330W Hybrid Discharge Moving Head Beam Instruction Manual
Congratulations on choosing a Claypaky product! We thank you for your custom. Please note that this product, as all the others in the rich Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.
1. SAFETY INFORMATION
SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and
keep the safety information on this product, also available in digital format
at the following link: www.claypaky.com
Ref: [FIS01H: Safety information Sharpie Plus]
2. UNPACKING AND PREPARATION
3. INSTALLATION AND START-UP
3.1 Installing the fixture
Light collimation system This product contains internal light collimation
system. Avoid intense light from any angle.
Installing the projector – Fig. 4 The projector can be installed on the floor
resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the
floor, the safety cable must be fitted. (Cod. 105041/003 available on
request). This must be securely fixed to the support structure of the
projector and then connected to the fixing point at the centre of the base.
3.2 Connecting to Manis supply
3.3 Connecting the control signal line: DMX / Art-Net 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded,
120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those
specified. The end connections must be made using XLR type 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a
resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the
metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
3.4 Switching on the fixture and basic Set Up
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt
move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel
(Fig. 8) has a display and buttons for the complete programming and management
of the projector menu. The display can be in one of two conditions: rest
status and setting status. When it is in the rest status, the display shows
the projector’s DMX address. During menu setting status, after a wait time
(about 30 seconds) without any key having been pressed, the display
automatically returns to rest status.
F It should be noted than when this condition occurs, any possible value that
has been modified but not yet confirmed with the key will be cancelled.
B C To activate this function, press UP ▲ and DOWN ▼ keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal
(addresses from 1 to 512). The address can also be set with the projector
switched off. If there is no DMX input signal, the display will show “No
signal”.
Functions of the buttons – Using the menu
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can
also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press RIGHT ▶ to momentarily activate the display and
thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
4. MAINTENANCE
4.1 Opening the covers
Locking and releasing Pan and Tilt movements – Refer to the instructions
in the UNPACKING AND PREPARATION section. Opening the head covers – Fig.
10.
Closing the head covers – Fig. 11.
4.2 Periodical cleaning
Periodical cleaning – Fig. 12
To ensure optimal operation and performance for a long time it is essential to
periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on
various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.). Use a
soft cloth dampened with any detergent liquid for cleaning glass to remove the
dirt from the reflectors, from the lenses and filters. It is recommended that
the projector undergoes an annual service by a qualified technician for
special maintenance involving at least the following operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
NOTE: keep a careful cleaning of the ”CMY/colour filters assembly” to prevent rapid deterioration.
4.3 Effects module removal
Extraction of the effect modules – Fig. 13.
IMPORTANT: Grasp the modules using the support structure and not the
details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig.
13, 14 and 15 in reverse order.
NOTE:
– Do not disconnect wiring harnesses when the fixtures is switched-on, to
avoid to damage electronic boards.
– Do not switch-on the fixtures with wiring harness disconnected.
4.4 – Cleaning of the filters
Cleaning of the filters – Fig. 14.
Lamp change – Fig 15.
Take the new lamp out of its package and insert in the fitting. WARNING: do
not touch the lamp’s envelope with bare hands. Should this happen, clean the
bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.
Lamp regulation
To centre the lamp, turn the adjusting screw as shown in the figure.
WARNING: The lamp must be adjusted with the projector switched off. After
adjusting, close the effects covers, switch on the projector and check that
the adjustment has been correctly made. If necessary, switch off the
projector, remove the effects covers and repeat lamp adjustment.
REMARK:
– Lifetime of the lamp will be influenced by the switching cycle.
– After a successful starting, attempt to keep the lamp burning for at
least 15 minutes in order to complete the chemical cycle of the lamp to
secure the lifetime.
– After switching-off the lamp wait at least 2 minutes before switching-on
it again.
4.5 – Rotating gobos
Bearing group replacement – Fig. 16
Gobo orientation – Fig. 17
The pictures shown the correct gobos orientation.
Replacing rotating gobos – Fig. 18
– Before use custom gobos contact Claypaky;
– The original gobos have a special coating designed specifically to resist
to the high temperatures;
– The rotating gobo wheel only use dichroic glass gobos (it is not possible
to use metal gobos);
– For more information contact Claypaky;
4.6 Battery removal
Battery removal – Fig. 19
This product contains a rechargeable battery. To preserve the environment,
please dispose the battery at the end of its life according to the regulation
in force.
5. SPECIFICATIONS
POWER SUPPLIES
AC power input Neutral Pomeron True1 (IP65) 100-240V, 50/60 Hz
INPUT POWER 540 VA
@230Vac – 50Hz
LIGHT SOURCE
Source: 330W X8 HRI Sirius Osram arc lamp Lamp average lifetime: 1500 hrs
MOTORS
Stepper motors, operating with micro-steps, totally microprocessor controlled
CHANNELS 31
control channels
INPUTS
DMX 512 Art-Net
IP RATING
IP 20 – Protected against the entry of solid bodies larger than 12mm (0.47″);
No protection against the entry of liquids.
SAFETY SPECIFICATIONS
Minimum distance of illuminated objects 8 meters Minimum distance from
flammable materials 0.2 meters Max ambient temperature 40°C (104°F) Max
temperature of the external surface 90°C (194°F) Automatic break in power
supply in case of overheating Forced ventilation with axial fans
ELECTRONICS
Long life self-charging buffer battery Function reset from the lighting desk
“AUTOTEST” function from menu Electronic monitoring with status error Cooling
system monitoring
DMX level monitoring on all channels Internal data transmission diagnostics Firmware Upgrade via Web Server Firmware upload from another fixture Protocols/Functions: RDM, Web Server
OPTICS
Zoom 3°- 36°, Linear and motorized
EFFECTS SECTION
Six beam reducers (down to 0.5°)
CMY colour mixing
15 colours on 3 wheels
2 CTO filters
Rotating Gobo Wheel: 8 interchangeable glass gobos
Static Gobo Wheel: 18 fixed gobos
Rotating 4-facet prism on dedicated channel
Rotating 8-facet prism on dedicated channel
Dynamic Animation disc
Linear soft edge frost filter
Dimmer and stop/strobe
Dense, Sharp, Parallel Light Beams
Extremely quick movements
Excellent visual effect projections
Wide and sharp aerial effects
CONTROL AND PROGRAMMING
DMX 512 control channels
Control signal USITT DMX 512
Protocols RDM, Webserver and Art-Net
Display Graphic LCD backlit b/w Display
Display battery Long life self-charging buffer battery
Pan/Tilt Resolution 16 bit
Focus Resolution 16 bit
Gobo Resolution 16 bit
Dimmer Resolution 16 bit
DMX signal connection 5 pole XLR input and output
Ethernet Input
Firmware update Software upload through
Ethernet input
BODY
Aluminium and steel structure with plastic covers Two side handles for
transportation Device locking PAN and TILT mechanisms for transportation and
maintenance
MOVING BODY
PAN range 540°
TILT range 270°
WORKING POSITION
Working in any position Hanging system: with fast-lock omega clamps (1/4 turn)
on the base
CE MARKING
In conformity with the European Directives:
- 2014/35/EU – Safety of electrical equipment supplied at low voltage (LVD)
- 2014/30/EU – Electromagnetic Compatibility (EMC)
- 2011/65/EU – Restriction of the use of certain hazardous substances (RoHS)
- 2009/125/EC – Eco-design requirements for Energy-related Products (ERP)
WEIGHT & DIMENSIONS
23.0 Kg
Cause and solution of problems
CLAYPAKY S.p.A. – Via Pastrengo, 3/b – 24068 Seriate (BG) Italy – Tel. +39-035-654311 – Fax +39-035-301876 – www.claypaky.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>