signify Chloride Exit/Emergency Compac CLU2, CLU3 User Guide
- June 6, 2024
- signify
Table of Contents
signify Chloride Exit/Emergency Compac CLU2, CLU3 User Guide
The Chloride Compac emergency units were designed to complement the Compac exit/emergency family in looks and reliability. They allow for immediate and safe egress in low light situations and work in harmony within commercial and light industrial applications. The CLU2 two lamp head model can be adjusted to provide the optimum amount of illumination. The CLU3’s center lamp head is stationary while the two side lamps can be adjusted for the perfect left and right angles. These units come standard with self-diagnostic/self-test features to assure that they are ready at any time.
Ordering guide
- Optional features cannot be combined with other optional features
- CLU2 feeds 2 single or 1 dual LED remote unit
- 15 minute delay
- Performs a manual test up to 40ft from unit, See RLT accessory for laser tester
- Available in white finish housing only, feeds 4 single or 2 dual LED remote lamp heads
- Contains self-diagnostic electronics but does not perform the automatic monthly test. Available in white finish housing only
- CLU3 unit with the 1R option feeds 1 LED remote lamp head
Accessories (order separately)
- WG5 – Wire guard (for CLC exit/unit combos mounted flat against the wall)
- RLT – Remote Laser Tester
CLU2/CLU3 Compac emergency unit
Dimensions
Performance
Meets Life Safety Code Illumination standard average of 1.0 FC, no point less
than 0.1 FC max to min ratio of 40:1.
Assumes open space with no obstructions. NFPA 101, Life Safety Code matches
California Fire Code of Regulations, Title 24. Normal operation (off/standby)
is not to be confused with emergency operation.
†Based on 6ft corridor and 9ft ceiling height and a mounting height of 7.5ft.
‡Based on 200ft by 200ft open area and 30ft ceiling height.
Codes and standards
- NFPA 70 (National Electric Code)
- NFPA 101 (Life Safety Code)
- ETL listed to Standard 924
- UL Listed for damp locations
Construction
- Wall or ceiling mounted
- UL 94 V-0.5VA Flame rated, UV stable thermoplastic housing
- Provisions for surface mounted conduit to top of wall mounted unit
- Back plate keyhole slots are easily removable knockouts for securing to single gang boxes, 3″ J-boxes and 4″ J-boxes
Installation
- Designed for wall or ceiling mount with a universal J-box pattern on back plate
- Surface conduit entry on top of housing in center of backplate
- CLUx unit mounts single gang boxes, 3″ J-boxes and 4″ J-boxes
Electronics
- 120/277VAC, 50-60Hz dual voltage selectable input
- Surge protected, solid state circuitry
- Charging systems are complete with low voltage disconnect (prevents deep discharge of battery), battery lockout
(prevents discharge of battery during installation), and brownout protection
Power consumption
- CLU2 120V=0.036/277V=0.030
- CLU3 120V=0.055/277V=0.040
Lamps
- CLU2 unit contains two – 2.2W adjustable LED lamp heads longlife LED lamp source head (5000K)
- CLU3 unit contains three – 2.2W LED lamp heads longlife LED lamp source head (5000K) (two adjustable, one fixed)
Battery
- Maintenance-free sealed 7.2v Nickel Metal Hydride battery
- Manual test switch and LED light indicator
- Supplies emergency illumination for a minimum of 90 minutes
- Batteries have an approximated service life of 6 to 8 years at a operating temperature range of 10°C to 40°C (50°F to 104°F)
Remote capability
- CLU2 emergency unit provides enough remote capability to supply DC power to 2 (CLR1W) LED remote lamps heads or 1 (CLR2W) dual LED remote lamp head.
- CLU3 provides enough remote capability to feed one CLR1W LED remote lamp head.
Listings
- California Energy Commission, Title 20 compliant (Battery Charger)
Warranty
- Five year full warranty on unit.
Self-diagnostics/Self-test
The CLU2/3 units contain selfdiagnostic/self-test electronics as a standard feature. An automatic self-test is performed every month for 3 minutes, and a 30 minute self-test every six months. A manual test may also be performed at anytime by pressing the manual test button.
Manual testing:
Self-Diagnostic Red status indicator:
The Self-diagnostic/selftest electronics meets the requirements of the National Electric Code and/or the National Fire Protection Association.
The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract.
© 2020 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify
Signify North America Corporation
200 Franklin Square Drive,
Somerset, NJ 08873
Telephone 855-486-2216
Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone 800-668-9008
All trademarks are owned by Signify Holding or their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>