TELTONIKA FMT100 Special and Small Waterproof Tracker User Manual

TELTONIKA FMT100 Special and Small Waterproof Tracker

Know Your Device

Pinout

Pin Number

| Pin Name|

Description

---|---|---

1

|

VCC (10-30)V DC (+)

|

(Red) Power supply (+10-30 V DC)

2

|

GND (-)

|

(Black) Ground

Setup Your Device

Insert Micro-SIM Card and Connect the Battery

1. Unscrew 6 screws counterclockwise.
   

2. Remove the cover.
   

3. Insert Micro-SIM card as shown with PIN request disabled or read our Wiki how to enter it later with Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
   

4. Connect the battery as shown to device. Position the battery in place where it does not obstruct other components.
   

5. After configuration, see “PC Connection (Windows)”, attach device cover back and screw in all screws.
   

6. Device is ready to be mounted.
   

PC Connection (Windows)

1. Power-up FMT100 with DC voltage (10 – 30 V) power supply using power wires. LED’s should start blinking, see “LED indications”.
2. Connect device to computer using Micro-USB cable or Blue-tooth connection:
   • Using Micro-USB cable
   • You will need to install USB drivers, see “How to install USB drivers (Windows)”
   • Using Blue-tooth
   • FMT100 Blue-tooth is enabled by default. Turn on Blue-tooth on your PC, then select Add Blue-tooth or other device > Blue-tooth. Choose your device named – “FMT100_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.

Install USB Drivers (Windows)

1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.

Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first FMT100 device will have default factory settings set. These settings should be changed according to the user’s needs. Main configuration can be performed via Teltonika Configurator software. Get the latest Configurator version from here. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET Requirements

Operating system|

MS .NET Framework version

| Version|

Links

Windows Vista Windows 7
Windows 8.1
Windows 10|

MS .NET Framework 4.6.2

| 32 and 64 bit|

www.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner.

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMT100 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

1. Load from device – loads configuration from device.
2. Save to device – saves configuration to device.
3. Load from file – loads configuration from file.
4. Save to file – saves configuration to file.
5. Update firmware – updates firmware on device.
6. Read records – reads records from the device.
7. Reboot device – restarts device.
8. Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured.
More details about FMT100 configuration using Configurator can be found in our Wiki.

Quick SMS Configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
” setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006;0″

Note: Before SMS text, two space symbols should be inserted.

GPRS settings:

• 2001 – APN
• 2002 – APN username (if there are no APN username, empty field should be left)
• 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

• 2004 – Domain
• 2005 – Port
• 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Default Configuration Settings

Movement and ignition detection:

• Vehicle movement will be detected by accelerometer
• Ignition will be detected by vehicle power voltage between 13,2 – 30 V

Device makes a record On Moving if one of these events happen:

• 300 seconds passes
• Vehicle drives 100 meters
• Vehicle turns 10 degrees
• Speed difference between last coordinate and current position is greater than 10 km/h

Device makes a record On Stop if:

• 1 hour passes while vehicle is stationary and ignition is off

Records sending to server:

• If device has made a record it is sent to the server every 120 seconds

After successful SMS configuration, FMT100 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.

Mounting Recommendations

• Device fastening

  • Locate the battery in your vehicle. If present remove the battery cover to access the battery.
  • There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.
    

• Connecting power wire

  • Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.

• Connecting ground wire

  • Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.
    

LED Indications

Navigation LED Indications

Behaviour

|

Meaning

---|---
Permanently switched on|

GNSS signal is not received

Blinking every second|

Normal mode, GNSS is working

Off|

GNSS is turned off because:
Device is not working or Device is in sleep mode

Blinking fast constantly|

Device firmware is being flashed

Status LED Indications

Behaviour

|

Meaning

---|---
Blinking every second|

Normal mode

Blinking every two seconds|

Sleep mode

Blinking fast for a short time|

Modem activity

Off|

Device is not working or Device is in boot mode

Characteristics

Basic Characteristics

Module

Name|

TM2500

Technology|

GSM, GPRS, GNSS, BLUE-TOOTH

GNSS

GNSS|

GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS

Receiver|

33 channel

Tracking sensitivity|

-161 dBM

Accuracy|

< 3 m

Hot start|

< 1 s

Warm start|

< 25 s

Cold start|

< 35 s

Cellular

Technology|

GSM

2G bands|

Quad-band 850 / 900 / 1800 / 1900 MHz

Data transfer|

GPRS Multi-Slot Class 12 (up to 240 kbps), GPRS Mobile Station Class B

Data support|

SMS (text/data)

Power

Input voltage range|

10 – 30 V DC with overvoltage protection

Internal fuse|

3 A, 125 V

Back-up battery|

170 mAh Li-Po battery 3.7 V (0.63 Wh)

Power consumption| At 12V < 2,5 mA (Ultra Deep Sleep)
At 12V < 5 mA (Deep Sleep)
At 12V < 5,5 mA (Online Deep Sleep)
At 12V < 6,5 mA (GPS Sleep)
At 12V < 24 mA (nominal with no load)
At 12V < 0.25 A Max. (with full Load / Peak)

Bluetooth

Specification|

4.0 + LE

Supported peripherals

|

Temperature and Humidity sensor, Headset, OBDII dongle, Inateck Barcode Scanner

Interface

GNSS antenna|

Internal High Gain

GSM antenna|

Internal High Gain

USB|

2.0 Micro-USB

LED indication|

2 status LED lights

SIM|

Micro-SIM

Memory|

128MB internal flash memory

Physical Specification

Dimensions|

92,5 x 57,6 x 14 mm (L x W x H)

Weight|

63 g

Operating Environment

Operating temperature (without

battery)

|

-40 °C to +85 °C

Storage temperature (without

battery)

|

-40 °C to +85 °C

Operating humidity|

5% to 95% non-condensing

Ingress Protection Rating|

IP65

Battery charge temperature|

0 °C to +45 °C

Battery discharge temperature|

-20 °C to +60 °C

Battery storage temperature|

-20 °C to +45 °C for 1 month

 |

-20 °C to +35 °C for 6 months

Features

Sensors|

Accelerometer

Scenarios|

Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip

Sleep modes|

GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep

Configuration and firmware update|

FOTA Web, FOTA, Teltonika Configurator (USB, Blue-tooth), FMBT mobile application (Configuration)

SMS|

Configuration, Events, Debug

GPRS commands|

Configuration, Debug

Time Synchronization|

GPS, NITZ, NTP

Fuel monitoring|

OBDII dongle

Ignition detection|

Accelerometer, External Power Voltage, Engine RPM (OBDII dongle)

Electrical Characteristics

Characteristic Description|

Value

---|---

Min.

| Typ.| Max.|

Unit

Supply Voltage

Supply Voltage (Recommended Operating Conditions)|

+10

|  | +30|

V

Safety Information

This message contains information on how to operate FMT100 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

• The device uses a 10 V…30 V DC power supply. The nominal voltage is 12 V DC. The allowed range of voltage is 10 V…30 V DC.
• To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
• Before unmounting the device from vehicle, ignition MUST be OFF.
• All related devices must meet the requirements of EN 62368-1 standard.

Warranty

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.
Contact us teltonika.lt/company/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the product can be:

• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same functionality
• TELTONIKA can also repair products that are out of warranty at an agreed cost.

Warranty Disclaimer

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
More information can be found at teltonika.lt/warranty- repair

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>