i Safe MOBILE IS-TH1xx.2 Mobile Multifunctional Set User Manual
- June 6, 2024
- i safe MOBILE
Table of Contents
- < IS-TH1xx.2 >
- MODEL MTHA10 / MTHA11
- > PRODUCT DESCRIPTION
- > INTRODUCTION
- > RESERVATION
- > EX-SPECIFICATIONS
- > EU-DECLARATION OF CONFORMITY
- > NAME CONCEPT
- > FAULTS AND DAMAGES
- > EX-RELEVANT SAFETY REGULATIONS
- > FURTHER SAFETY ADVISES
- > MAINTENANCE/REPAIR
- > INSTALLATION
- > RECYCLING
- > TRADEMARKS
- CONTACT/SERVICE CENTER
- > EU-DECLARATION OF CONFORMITY
QUICK START MANUAL
SAFETY INSTRUCTIONS
< IS-TH1xx.2 >
MODEL MTHA10 / MTHA11
> PRODUCT DESCRIPTION
Document No. 1054MM01REV00
Version: 2021-06-01
(c) 2021 i.safe MOBILE GmbH
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
Tel. +49 9343/60148-0
info@isafe-mobile.com
www.isafe-mobile.com
Template: TEMPMM01REV10
> INTRODUCTION
This document contains information and safety regulations which are to be
observed without fail for safe operation of the device IS-TH1xx.2 (Model
MTHA10 / MTHA11) under the described conditions. Non-observance of this
information and instructions can have serious consequences and / or may
violate regulations.
Please read the manual and these safety instructions before using the device.
In case of any doubt, the German version shall apply.
The current EU-declaration of conformity, certificates, safety instructions
and manuals can be found at www.isafe-mobile.com or requested from i.safe MOBILE GmbH.
> RESERVATION
The content of this document is presented as it currently exists. i.safe
MOBILE GmbH does not provide any explicit or tacit guarantee for the
accuracy or completeness of the content of this document, including, but not
restricted to, the tacit guarantee of market suitability or fitness for a
specific purpose unless applicable laws or court decisions make liability
mandatory.
i.safe MOBILE GmbH reserves the right to make changes to this document or
to withdraw it any time without prior notice. Changes, errors and misprints
may not be used as a basis for any claim for damages. All rights reserved.
i.safe MOBILE GmbH cannot be held responsible for any data or other loss
and direct or indirect damages caused by any improper use of this device.
> EX-SPECIFICATIONS
The device IS-TH1xx.2 is suitable for use in potentially explosive atmospheres classified zone 2/22 in accordance with directives 2014/34/EU and 2014/30/EU, as well as the IECEx scheme.
EX-MARKINGS
> > ATEX:
II 3G Ex ic op is IIC T4 Gc
II 3D Ex ic op is IIIC T135°C Dc
Certificate of Conformity:
EPS 21 ATEX 1 082 X
CE-designation:
> > IECEx:
Ex ic op is IIC T4 Gc
Ex ic op is IIIC T135°C Dc
IECEx Certificate: IECEx EPS 21.0028X
> > Temperature range:
-20°C … +60°C (EN/IEC 60079-0)
-10°C … +50°C (EN/IEC 62368-1)
> > Manufactured by:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
> EU-DECLARATION OF CONFORMITY
The EU-declaration of conformity can be found at the end of this manual.
> NAME CONCEPT
The two “xx” in IS-TH1xx.2 are placeholders. The IS-TH1xx.2 comes in two variants with different scan ranges and scan engines:
name (model) | scan range | scan engine |
---|---|---|
IS-TH1MR.2 (MTHA10) | mid range | Zebra SE4750 (MR) |
IS-TH1ER.2 (MTHA11) | extended range | Zebra SE4850 (ER) |
> FAULTS AND DAMAGES
If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:
> > Malfunctions occur.
> > The housing of the device shows damage.
> > The device has been subjected to excessive loads.
> > The device has been stored improperly.
> > Markings or labels on the device are illegible.
We recommend that a device displaying errors or in which an error is suspected
be sent back to i.safe MOBILE GmbH to be checked.
> EX-RELEVANT SAFETY REGULATIONS
Use of this device assumes that the operator observes the conventional safety
regulations and has read and understood manual, safety instructions and
certificate.
When used in ex-hazardous areas, the following safety regulations must also be
complied with:
> > The device may be connected only outside ex-hazardous areas to the
IS530.2 via the ISM interface.
> > To ensure the IP-protection, it has to be ensured that all gaskets
are present and functional. There must be no large gap between the halves of
housing.
> > The device must be securely fastened to the ISM interface when used
in ex-hazardous areas.
> > The device may not be exposed to any aggressive acids or alkalis.
> > The device may only be used in zone 2/22.
> > Only accessories approved by i.safe MOBILE GmbH may be used.
> FURTHER SAFETY ADVISES
CAUTION
Laser Light. Do not stare into beam class 2 laser product 630 – 680 nm, 1 mW.
> > Do not put the device in environments with excessive temperatures.
> > Do not use the device in areas where regulations or legislatives
prohibit the use.
> > Do not expose the device to strong magnetic fields, such as are
emitted from induction ovens or microwaves.
> > Do not attempt to open or repair the device. Improper repair or
opening can lead to the destruction of the device, fire or explosion. Only
authorized personnel are allowed to repair the device.
> > Observe all corresponding laws that are in force in the respective
countries regarding the use of devices while operating a vehicle.
> > Please power off the device before cleaning the device.
> > Do not use any chemical cleaning agents to clean the device. Use a
damp and anti-static soft cloth for cleaning.
> > The user alone is responsible for any and all damages and liabilities
caused by malware downloaded when using the network or other data-exchange
functions of the device. i.safe MOBILE GmbH cannot be held responsible for
any of those claims.
WARNING
i.safe MOBILE GmbH will not assume any liability for damages caused by
disregarding any of these advices or by any inappropriate use of the device.
> MAINTENANCE/REPAIR
Please note any legal requirements for periodic inspection.
The device itself has no user-serviceable parts. It is recommended to perform
inspections according to the safety regulations and advises. If there is a
problem with the device, please contact your vendor or consult the service
center. If your device is in need of repair, you can either contact the
service center or your vendor.
> PRODUCT DESCRIPTION (see illustration on page 2)
1 > HOLDER: Holder for IS530.2
2 > PLUG: Connecting IS530.2
3 > SCAN BUTTON: Scanning barcodes.
4 > EYELET: Eyelet for hand strap.
> INSTALLATION
WARNING
The device may be connected only outside ex-hazardous areas to the IS530.2 via
the ISM interface!
> > Unscrew the cover of the ISM interface (1) located on the IS530.2.
> > Push the IS530.2 completely into the holder (2) of the device.
> > Unscrew the screw (3).
> > Loosen the plug (4).
> > Attach the plug on top of the ISM interface (5).
> > Fix the plug by pressing the rounded end of the plug (6).
> > Tighten the screw (7).
> > Check whether the plug is correctly and firmly attached to the ISM
interface.
The device can now be used together with the IS530.2 inside ex-hazardous
areas.
> RECYCLING
The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. More detailed information is available from the product retailer, local waste authorities, national producer responsibility organisations, or your local i.safe MOBILE GmbH representative.
Correct Disposal of this product. This marking indicates that this product should not be dispose other household wastes throughout the EU. To prevent possible harm to the environment or human he from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
> TRADEMARKS
> > i.safe MOBILE and the i.safe MOBILE logo are registered trademarks of the i.safe MOBILE GmbH.
CONTACT/SERVICE CENTER
FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTER:
> > i.safe MOBILE GmbH, i_Park Tauberfranken 10, 97922 Lauda-
Koenigshofen, Germany
> > support@isafe-mobile.com
> > https://support.isafe-mobile.com
> EU-DECLARATION OF CONFORMITY
EU - Declaration of Conformity
according to directive 2014/34/EU, 2014/30/EU, 2014/35/EU and 2011/65/EU (2015/863/EU)
The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards:
Name & address of the manufacturer in the EU| i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda - Koenigshofen, Germany
---|---
Description of the devices| Trigger Handle
type: IS-TH1MR.2 and IS-TH1ER.2
model: MTHA10 and MTHA11
Ex - marking| II 3G Ex ic op is IIC T4 Gc
II 3D Ex ic op is IIIC T135°C Dc
Conformity statement 2014/34/EU issued by
Applied harmonized standards
| EPS 21 ATEX 1 082 X
Bureau Veritas E&E Product Services GmbH
Businesspark A96
86842 Tuerkheim, Germany
identification number: 2004
EN IEC 60079-0:2018; EN 60079-11:2012; EN 60079-28:2015
Conformity statement 2014/30/EU, 2014/35/EU and 2015/863/EU amending 2011/65/EU issued by
Applied harmonized standards
| Shenzhen TCT Testing Technology Co., Ltd.
1B/F., Building 1, Yibaolai Industrial Park,
Qiaotou, Fuyong, Baoan District, Shenzhen,
Guangdong, China
EN 55032:2015; EN 55035:2017;
EN 62368-1:2014+A11:2017;
IEC 62321-2:2013;
IEC 62321-3-1:2013; IEC 62321-5:2013;
IEC 62321-4:2013 + AMD1 2017;
IEC 62321-7-1:2015; IEC 62321-7-2:2017;
IEC 62321-6:2015; IEC 62321-8:2017;
EN 60825-1:2014; EN62471:2008
CE Marking|
Lauda Koenigshofen 25.05.2021
Dirk Amann
Managing Director
1054CC01REV00_jru All rights reserved, i.safe MOBILE GmbH
Documents / Resources
| i
Safe MOBILE IS-TH1xx.2 Mobile Multifunctional
Set
[pdf] User Manual
IS-TH1xx.2, Mobile Multifunctional Set
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>