i safe MOBILE M53A01 IS530.2 Cell Phone User Guide

i safe MOBILE M53A01 IS530.2 Cell Phone

EX MARKINGS

• ATEX:
  II 3G Ex ic IIC T4 Gc IP64
  II 3D Ex ic IIIC T135°C Dc IP64 Certificate of Conformity:
  EPS 19 ATEX 1 070 X
  CE-designation:

• IECEx:
  Ex ic IIC T4 Gc IP64
  Ex ic IIIC T135°C Dc IP64
  IECEx Certificate: IECEx EPS 19.0033X

• North America:
  Class I Div 2 Groups A, B, C, D, T4
  Class II Div 2 Groups F, G , T135˚C
  Class III Div 2
  CSA19CA70220252

• Temperature range:
  – 20°C … +60°C (EN/IEC 60079-0)
  – 10°C … +50°C (EN/IEC 62368-1)

• Manufactured by:
  i.safe MOBILE GmbH
  i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany

EX-RELEVANT SAFETY REGULATIONS

Use of this device assumes that the operator observes the conventional safety regulations and has read and understood manual, safety instructions and certificate.
The following safety regulations must also be complied with:

• Inside ex-hazardous areas the covers of all interfaces must be closed.
• To ensure the IP-protection, it has to be ensured that all gaskets are present
• and functional. There must be no large gap between the two halves of the housing.
• The device may only be charged outside ex-hazardous areas.
• Physical connections to equipment other than the IS-HS1.1 or IS-HS1.2 headset are only allowed outside ex-hazardous areas using equipment approved by i.safe MOBILE GmbH.
• When using the  IS-HS1.1 or IS-HS1.2 headset, the headset must be securely fastened to the ISM interface.
• The device may only be charged at ambient temperatures between +5°C … +35°C.
• The device may not be exposed to any aggressive acids or alkalis.
• The device may only be used in zones 2 or 22.
• Only accessories approved by i.safe MOBILE GmbH may be used.

EX-RELEVANT SAFETY REGULATIONS FOR NORTH AMERICA

• The battery shall only be charged outside the explosion hazardous areas only and using a suitably certified Class 2 power supply with the following output parameters:
  V = 5VDC I = 2000mA

• The smartphone must be protected against excessive UV light emission and high electrostatic processes.

• The USB interface (type C) located at the bottom side is for data transmission and it is used in non hazardous areas. It is not permitted to open the USB interface cover in hazardous locations.

• The ISM interface of the IS530.2 located at the right side can be used within hazardous areas with approved headsets, Remote Speaker Microphones(RSM) and add-ons.

• For the ISM interface connection the intrinsically safe approved accessories must comply with entity parameters according to document 1029AD04 i.e. Headset IS-HS1.1 and IS-HS1.2 is approved to be used on ISM interface. If the ISM interface is not used, it must be securely closed by the cover provided for this purpose.

INFORMATION CONCERNING SAR CERTIFICATION

(SPECIFIC ABSORBATION RATE)

Maximum SAR values for this model and the conditions under which these were determined:

• SAR (head)  0.81 W/kg
• SAR (body – worn) 1.54 W/kg

This device was tested for typical body-worn operations with the back of the handset kept 5 mm from the body. The device complies with RF specifications when the device used at 5 mm from your body.

The product shall only be connected to a USB interface of version USB2.0. Adapter shall be installed near the equipment and shall be easily accessible.

NB WARNING

CAUTION

• Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss.
• CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
• Operation temperature: -20°C …+60°C (EN/IEC 60079-0)/ -10°C …+50°C (EN/IEC 62368-1). The device shall only be connected via accessory authorised by i.safe MOBILE GmbH.
• AC Adapter:
  • Approved external adapter model ICP12-050-2000B (Input: AC100-240V 50/60Hz 0.3A; Output: 5VDC, 2A) or other approved external AC/DC adapter which complies with the requirements of LPS (Limited Power Source) and has output rated 5VDC/2A.
  • Adapter shall be installed near the equipment and shall be easily accessible.
  • The plug is considered independent of the adapter.
• The device complies with RF specifications when the device used at 0.5 cm from your body.
  The i.safe MOBILE GmbH hereby declares that this smart phone is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. This information has to be presented in such a way that the user can readily understand it. Typically, this will necessitate translation into every local language (required by national consumer laws) of the markets where the equipment is intended to be sold. Illustrations, pictograms and using inter-national abbreviations for country names may help reduce the need for translation.

EU-DECLARATION OF CONFORMITY

EU – Declaration of Conformity according to directive 2014/34/EU, 2014/53/EU and 2011/65/EU (2015/863/EU)

The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards:

Name & address of the manufacturer in the EU Name & Anschrift des Herstellers innerhalb der europäischen Gemeinschaft| i.safe MOBILE GmbH i_Park Tauberfranken 10

97922 Lauda – Koenigshofen

Germany

---|---
Description of the devices

Beschreibung der Geräte

| Explosion protected smartphone Explosionsgeschütztes Smartphone type / Typ : IS530.2 & IS-HS1.1

model / Model : M53A01

Ex – marking

Ex – Kennzeichnung

| II 3G Ex ic IIC T4 Gc IP64

II 3D Ex ic IIIC T135°C Dc IP64

Conformity statement 2014/34/EU issued by Konformitätsaussage 2014/34/EU| EPS 19 ATEX 1 070 X

__

Bureau Veritas E&E Product Services GmbH Businesspark A96

86842 Tuerkheim, Germany

identification number / Kenn-Nummer : 2004

Applied harmonized standards

| EN IEC 60079-0:2018; EN60079-11:2012
Conformity statement 2014/53/EU issued by| PHOENIX TESTLAB GmbH
2014/53/EU| Koenigswinkel 10
| 32825 Blomberg
| Germany
| identification number / Kenn-Nummer : 0700
Applied harmonized standards| EN 62368-1:2014+A11:2017;
| EN 50332-1:2013;
| EN 50332-2:2013;
| EN 50360:2017;
| EN 50566:2017;
| EN IEC 62311:2020;
| EN 62479:2010;
| EN 50663:2017;
| EN 62209-1:2016;
| EN 62209-2:2010+A1:2019;
| ETSI EN 301 489-1 V2.2.3;

ETSI EN 301 489-3 V2.1.1;

ETSI EN 301 489-17 V3.2.4;

ETSI EN 301 489-19 V2.1.1;

Draft ETSI EN 301 489-52 V1.1.0; EN 55032:2015+A11:2020;

EN 55035:2017+A11:2020; ETSI EN 301 511 V12.5.1;

ETSI EN 301 908-1 V13.1.1;

ETSI EN 301 908-2 V13.1.1;

ETSI EN 300 328 V2.2.2;

ETSI EN 301 893 V2.1.1;

ETSI EN 300 440 V2.2.1;

ETSI EN 300 330 V2.1.1;

ETSI EN 303 413 V1.1.1

---|---
Conformity statement 2015/863/EU amending| SGS-CsTC Standards Technical Services Co.,
2011/65/EU issued by| Ltd.
| 198 Kezhu Road,
| Scientech Park Guangzhou Economic &
| Technology Development District,
| Guangzhou, China 510663
Applied harmonized standards| IEC 62321-2: 2013; IEC 62321-1: 2013;
| IEC 62321-3-1: 2013; IEC 62321-5: 2013;
| IEC 62321-4: 2013 + A1: 2017;
| IEC 62321-7-1: 2015;
| IEC 62321-7-2: 2017 & ISO 17075-1: 2017;
| IEC 62321-6: 2015;
| IEC 62321-8: 2017
CE Marking

|

References

• Zertifizierte Smartphones, Tablets und Mobiltelefone für IECEx und ATEX Zonen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>