JOOM V1 TWS True Wireless Stereo Bluetooth 5.0 Headphones Sports Earphones User Manual

V1 User Manual

Highlights

1. Dust-proof mesh
2. Multifunction button
3. Microphone
4. Charging connection point
5. LED light charging station
6. Micro USB charging port

Specifications:

TWS (True Wireless Stereo); Elite wireless design, individual channel left and right, HIFI True stereo sound with deep bass quality. Both the left and right earbuds are connected via Bluetooth. These can be used individually or as a pair.

earbuds, or to times for a single earbud.

*Note: Depends on phone brand, type, and/or model

AUTO ON/OFF:

This product is made with an auto sensor switch to turn the earbuds on and off automatically when you open or close the lid from the docking case. Open the lid is auto ON, close the lid is auto OFF.

TIP: The earbuds can also be manually set ON and OFF by the touch sensor button.

Pairing:

1. Pair with 1 earbud:

a)Open the docking case, the sensor switch will power it on, then the left and right earbuds will be paired to each other automatically. Then choose i of the 2 earbuds and close the case.

b)Turn on Bluetooth on your mobile device and select “Flinn Elite Wireless Earbuds” from the list. You will then hear a voice that says that you are”connected”. From now on you can listen to music and you are able to receive calls. The Elite Wireless earbuds also support incoming calls.

*Note:

During phone calls only earbuds works (depending on phone brand and/or model), you can keep the other earbud in the charging dock. When taking out the other earbud to use, both earbuds will connect each other automatically to be synchronized including the memory function.

2. Pair with both earbuds:

a)Open the docking case, the sensor switch will power it on, then the left and right earbuds will be paired to each other automatically. Take out both of the 2 earbuds, the right earbud work as host. When enabling Bluetooth on your device and select” Fling Elite Wireless Earbuds” from the list. When the LED light slowly blinks blue, the earbuds have been successfully connected. The battery status is visible on your mobile phone (if supported).

c)You will hear the message “connected” for verification.

Note:

During phone calls, two earbuds work, and on both sides, you can control Power off/Play/Pause individually during the connection. The other earpiece is then synchronized. The memory function is automatically supported when reconnecting both devices (both earbuds and the device) that were used last time!

Bluetooth use:

1. aking phone calls:
   Make sure the earbuds are connected to your mobile device. You can call now. With phone calls, 1 or 2 of the earbuds works. You will hear the telephone number when you receive a call. You answer the call by pressing the right or left touch button once. To reject the call, press zx quickly on the right or the left touch button so the call is rejected. When the earbuds are in music or standby mode, you can call the last telephone number again by pressing the right touch button 3x quickly. You can change the volume by pressing the touch button zx shortly on the right headset for volume + and zx shortly on the left touch button headset for volume — or change it by the volume buttons from your device directly.
   For Apple users that use SIRI: 3x quickly press on the left multifunction button headset to activate it.

2. Listen to your music
   Make sure that the earbuds are connected to your mobile device. You can now listen to the music on your playlist. ix short press the touch button to stop the music. Press the button again to continue. Long press the right touch button till the beep is heard for the next song and long-press the left touch button till the beep is heard for the previous song.

3. Power off
   Hold down the touch button until the LED light shows red. The Bluetooth device switches off, even when the earbuds are both connected as a set. If the earbuds have been removed from your Bluetooth device for more than 5 minutes, they will switch off automatically. You do not have to worry about an empty battery.

4. Charging
   You will hear a reminder sound when the battery is low. At the same time, the LED light will turn red on the earbuds. Place the earbuds inside the docking case and close the lid. During charging, the LED light turns red (to check open the lid a little bit to see the LEDs working), and it switches off automatically when it is fully charged.
   If both earbuds are empty and also the docking case, please re-charge the docking case at first with the micro USB charge cable. The docking case will be charged firstly (led with flash 1,2,3 till 4 LEDs all will ON 1 by still full) and when full it will automatically charge the earbuds till full (led will be ON from 4, 3, 2 till I led 1 by still empty) and then switch auto-off.
   Note: the earbuds will be switched off automatically during charging.

Warning:

1. Do not use the earbuds excessively and do not store them under heavy pressure. The earbuds are not resistant to heat and water.
2. Keep the earbuds away from the WIFI router or other high-frequency equipment and walls etc. to prevent interruption of signal reception.
3. Use the earplugs in the working range (max. io meters). The effect will be significantly better if there are no obstacles between the connected devices.
4. Use these Bluetooth earphones with any device with Bluetooth stereo
5. Do not press the earbuds too hard into the charging station if you want to charge them! A soft “magnetic click” indicates that they have been placed correctly. The LED light turns red when charging
6. When using the earbuds again, please keep them upright when you remove them from the charging station to prevent

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>