RYOBI R18DD2-220S Drill Driver User Manual
- June 9, 2024
- RYOBI
Table of Contents
ORIGINAL INSTRUCTIONS
R18DD2
R18DD2-220S Drill Driver
Important!
It is essential that you read the instructions in this manual before
assembling, maintaining and operating the product.
Subject to technical modification
Safety, performance, and dependability have been given top priority in the
design of your drill driver.
INTENDED USE
The drill driver is intended to be used only by adults who have read and
understood the instructions and warnings in this manual, and can be considered
responsible for theiractions.
The product can be used for drilling into various materials, including wood,
metal, and plastics using a drill bit having a shank diameter of less than 10
mm.
The product can be used to drive and remove screws and bolts using an
appropriate bit.
Do not use the product in any way other than those stated for intended use.
WARNING
Read all safety warnings, instructions, illustrations and specifications
provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fi re and/or serious injury.
Save all warnings and instruction for future reference.
DRILL DRIVER SAFETY WARNINGS
-
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Wear ear protectors when drilling. Exposure to noise can cause hearing loss.
-
When not in use, all tools should be disconnected from power source.
-
The dust produced when using the product may pose a health hazard. Do not inhale the dust. Wear a suitable dust protection mask..
-
Do not operate on materials (e.g., asbestos) that present a health hazard.
-
Switch off the product immediately if the bit stalls. Do not switch on the product again while the bit is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the bit stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded -
Sawdust and splinters must not be removed while the product is running.
-
When working in walls, ceilings, or floors, avoid hitting electrical cables and gas or water pipes.
-
Secure your workpiece with a clamping device.
-
Ambient temperature range for tool during operation is between 0 °C and 40° C.
-
Ambient temperature range for tool storage is between 0 °C and 40° C.
-
The recommended ambient temperature range for the charging system during charging is between 10 °C and 38° C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fi re, personal injury, and product damage due to a
short circuit, never immerse your tool, battery pack or charger in fluid or
allow a fluid to flow inside them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or bleach-containing
products, etc., can cause a short circuit.
- Ambient temperature range for battery during use is between 0 °C and 40° C.
- Ambient temperature range for battery storage is between 0 °C and 20° C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and
regulations.
Follow all special requirements on packaging and labelling when transporting
batteries by a third party. Ensure that no batteries can come in contact with
other batteries or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or tape. Do not
transport batteries that are cracked or leaking. Check with the forwarding
company for further advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following hazards may
arise, and the operator should pay special attention to avoid the following:
- Risk of electrocution if electric cables are drilled into. Always grasp the product by designated handles; do not touch the drill bits.
- Injury caused by vibration. Hold the product by designated handles and limit exposure to vibration. See “RISK REDUCTION”.
RISK REDUCTION
It has been reported that vibrations from hand-held tools may contribute to a
condition called Raynaud’s Syndrome in certain individuals. Symptoms may
include tingling,numbness and blanching of the fi ngers, usually apparent upon
exposure to cold. Hereditary factors, exposure to cold and dampness, diet,
smoking and work practices are all thought to contribute to the development of
these symptoms. There are measures that can be taken by the operator to
possibly reduce the effects of vibration:
- Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
- After each period of operation, exercise to increase blood circulation.
- Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately
discontinue use and see your doctor about these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using
any tool for prolonged periods, ensure you take regular breaks.
**KNOW YOUR PRODUCT
**
See page 81.
1. Gear selector | 6. Handle, insulated gripping surface |
---|---|
2. Torque adjustment ring | 7. LED lights |
3. Keyless chuck | 8. Bit storage |
4. Direction of rotation selector | 9. Screw driver bit |
5. Variable speed switch trigger | 10. Battery port |
MAINTENANCE
WARNING
The product should never be connected to a power supply when you are
assembling parts, making adjustments, cleaning, performing maintenance, or
when the product is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.
- When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
- Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt and carbon dust.
- Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
- Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
- For greater safety and reliability, all repairs should be performed by an authorised service centre.
LUBRICATION
All of the bearings in the product are lubricated with a sufficient amount of
high grade lubricant for the life span of the product under normal operating
conditions. Therefore, no further lubrication is required.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental friendly recycling.
SYMBOLS
**** | Safety alert |
---|---|
**** | CE conformity |
V | Volts |
**** | Direct current |
min-1 | Revolutions or reciprocations per minute |
Ø | Chuck capacity |
No load speed | |
**** | EurAsian Conformity Mark |
Please read the instructions carefully before starting the machine. | |
Ukrainian mark of conformity | |
Waste electrical products should not be disposed of with household waste. |
Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL
| Note
---|---
****| Warning
| Parts or accessories sold separately
| Torque, maximum
| Torque, minimum
| Speed, minimum
| Speed, maximum
The following signal words and meanings are intended to explain the levels of
risk associated with this product:
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result
in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
|
---|---
|
Product specifications|
---|---
Drill driver|
Model| R18DD2
Voltage| 18 V ****
Chuck| 2 – 10 mm
Switch – Variable speed|
No-load speed (Drill mode)|
LO Speed| 0 – 400 min-1
HI Speed| 0 – 1350 min-1
Clutch (positions)| 24
Maximum torque| 40 Nm
Maximum drilling capacity, in wood| 32 mm
Maximum drilling capacity, in metal| 10 mm
Weight – excluding battery pack| 1,0 kg
Weight – according to EPTA Procedure 01/2003| 1,42 kg
Battery and charger|
---|---
Compatible battery pack (not included)|
Lithium-Ion| RB18L13
RB18L15
RB18L20
RB18L25
RB18L40
RB18L50
Compatible charger (not included)| BCS618
BCL14181H
BCL14183H
RC18150
RC18627
RC18120
RC18118C
RC18115
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardized test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
RYOBI® WARRANTY APPLICATION CONDITIONS
In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.
-
The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
-
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
-
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
– any damage to the product that is the result of improper or lack of maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any product not displaying the CE approval mark on the rating plate
– any product that has been attempted to be repaired by a nonauthorized warranty service centre or without prior authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
– normal wear and tear spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– Power tool accessories provided with the tool or purchased separately, including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
– Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc. -
For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
-
This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit
http://en.ryobitools.eu/header/service-and-support/service-agents
EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Drill driver
Brand: Ryobi
Model number: R18DD2
Serial number range: 46271401000001 – 46271401999999
is in conformity with the following European Directives and harmonised
standards
2006/42/EC, 2014/30/EU, 2011/65/EU,
EN 60745-1:2009+A11:2010, EN 60745-2-1:2010,EN 60745-2-2:2010,
EN 55014-1:2017, EN 55014-2:2015
**** RoHS documentation is compiled according to EN 50581:2012
Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, May. 11, 2018
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
961075451-01https://tm.by
References
- Servis
- Ryobi Tools
- Servicio técnico | RYOBI España
- Ryobi Tools
- SAV Ryobi France: Pièces détachées et réparations Ryobi : le service client Ryobi
- Ryobi Tools HU
- Centri di assistenza
- Ryobi Tools - Aanbiedingen Ryobi Elektrisch & Tuingereedschap
- Ryobi Norge | Elverktøy, ONE+, Hagemaskiner, 36V
- Kontakt
- Serviços técnicos
- СервиÑные центры
- Ryobi Tools
- Servicecenter
- Ryobi Tools
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>