TWS Bluetooth Earbud QCY-T6 User Manual
- June 6, 2024
- QCY
Table of Contents
TWS Bluetooth Earbud QCY-T6
Overview
Choose Your Eartips
Please try medium eartips first as they fit most people.
How to Pair
First Time Pairing:
- Pick up both earbuds, pop both earbuds into the case to activate them.
- On cellphone, search for QCY-T6 and tap to connect.
- Once paired earbuds will auto power on upon picking up from the case. If earbuds fail to auto power on, please charge them and try again.
Switch Paired Device:
- Turn off phoneA’s Bluetooth faculty and earbuds will auto disconnect and enter into pairing mode.
- On phoneB, search for QCY-T6 and tap to connect.
- Multi-point connection is not available. Earbuds will auto reconnect to phoneB upon powering up again.
Factory Setting
(Try the following steps to fix connectivity issue) Set to factory:
- On cellphone, search for QCY-T6, tap and choose ignore or cancel pairing.
- Pick up two earbuds, keep touching both bars for 8s or until LEDs glow red for ls to power off.
- Keep touching both bars for 10s or until LEDs blink red and green 3 times then blink red to set earbuds to factory.
- Please refer “First Time Pairing” to connect after factory setting.
Manual Pairing (please refer the following steps in case two earbuds lose
connection)
Power off earbuds then keep touching panels for Ss or until LEDs blink red and
green. After then, double touch panels and LEDs will blink red and green. Two
earbuds will then auto pair with each other when LED on master earbud blinks
red and green and the other one turns off.
How to Wear
- Rotate earbud and pop it into your ear then shake head to check wearing stability.
- Please adjust mic towards your mouth to gain better calling experience.
Three-way Calling & Switch
Double touch the bar to answer incoming call. If another call is coming in sync, double touch again to put the first call on hold while activating the second one or keep touching the bar for 2s to ignore the second call. Keep touching the bar for 2s to switch between active call and held call.
Mono Mode
- Power off earbuds, hold Touch Panel on either earbud for Ss to enter pairing mode(LED blinks red and green).
- On cellphone, search for QCY-T6 and tap to connect.
- Connected.
Charging Earbud
Push earbud into t he case to charge. LED will glow sol id red when charging and turn to green for 1 minute once top up.
Charging the Case
LED on the case will glow sol id red when battery level is under 60%; LED wi ll turn green when battery level is between 60% and 95 and become solid blue when the battery level is over95%.
Product Parameters
Model: lnl947
Bluetooth version: VS.0
Charging time: approx. 2hr
Talking time: approx. 5.5hr
Operation range: l0m(with no obstacle)
Battery type: Ii-ion
Battery capacity(earbud): 3.7V 60mAh
Battery capacity(charging case): 3.7V 600mAh
Input parameter(charging case): 5V=600mA
Bluetooth profiles: HSP/HFP/A2DP/AVRCP
Pairing name: QCY-T6
Stand time: approx. 100hr
Music time: approx. 6 hr
Function Introduction
Fun c tion s| Curren t statu s|
Operatio n / r e s ult| LED| Promp t
---|---|---|---|---
Entering TWS Mode| Power-off with no connectivity record| Keep touching
the bar for ls to power on and earbud will auto enter pairing mode| LED blinks
red and green| TONE
Power off then keep touching the bar for 5s to enter pairing mode| Double
touch the bar to enter TWS mode| LED blink red and green then right LED turns
off| TONE
Power-on| Power-off| Keep touching the bar for ls| LED glows green for
ls| TONE
Charging| Pick up earbuds from the case| LED glows green for ls
Power-off| Power-on| Keep to uching the bar for 8s(only two unpaired
earbuds will be powered off together )| LED glows red for ls| TONE
Pop earbud int o the case to power off| LED glows red
An s w er / end call| Incoming call/calling| Double
touch the bar| | TONE
Ignore call| Incoming call| Keep touching the bar for 2s| | TONE
Monit o ring mode| Connected| Triple touch the bar on right
earbud| | \
Voice assistant| Connected| Triple touch the bar on left earbud| | TONE
Incoming call| Connected to phone| Incoming call ring| | call ring
Music pause / play| Music playing| Double touch the bar to
pause,double touch again to resume playing| | \
Skip track| Music playing| Keep touching right/left bar to skip track
forward/ backw ard| | \
Warranty Card
Warranty Period
12 months after you purchase this item.(or you may inquire your local shopper
for more details.)
Free Service:
Supposing any defects caused by quality issues occur within the warranty
period, please take this warranty card and purchase receipts to your
distributor for free exchange service.
Model Number:
Date of Purchasing:
User’s Name:
User’s Phone:
User’s Address:
Shop’s Name:
Shop’s Address:
Comments:
Free exchange service will not be accessed under following circumstances:
- Damages caused unauthorized disassembly.
- Defects or physical damages caused by leaking or dropping off.
- Damages by act of God.Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can rad iate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
rad io or television reception, which can be determined by turn ing the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circu it different from that to
which the receiver is connected.
— Consult the dealer or an experienced rad io/IV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) th is device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Hazardous substances and their contents in the item
Part Name
| Hazardous Substances
---|---
Pb| Hg| Cd| Cr (VI)| PBB| PBDE| DIBP| DEHP| DBP|
BBP
Mainbody| X| O| O| O| O| O| O| O| O|
O
Battery
| O| O| O| O| O| O| O| O| O| O
Ear tips| O| O| O| O| O| O| O| O| O|
O
Accessories
| O| O| O| O| O| O| O| O| O| O
Charging caole| X| O| O| O| O| O| O| O| O|
O
This form is made by SJ/T 11364 regulation.
O : means that hazardous substance content in the homogeneous materials of
this part is within the limits of (EU) 2015/863 regulation.
X : means that hazardous substance content in ,at least, one certain homogeneous material of this part is beyond the limits of (EU) 2015/863 regulation ,but there is no mature alternative in the industry at present, it still conforms to theEU ROHS Directive in the scope of exemption.
Notes: Please arrange using time properly as your hearing may be damaged by using the device for a long time.
Manufacturer: Dongguan Hele Electronics Co., Ltd.
Address: Daojiao Town, Dongguan City, Guangdong, China
Tips
- Before using the headset, please read the manual carefully and keep it for future references.
- The headset need to be fully charged prior to first-time use.
- If the headset is left unused for over two weeks, please recharge it periodically.
- Please use the chargers made by qualified manufacturer.
- If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.
Caveats
- Never disassemble or modify your headset for any reasons to avoid any damages and danger.
- Do not store the headset in extreme temperatures (under 0°C or over 45°C).
- Avoid using the indicator close to the eyes of children or animals.
- Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electricshock.
- Do not use harsh chemicals or strong detergents to clean the headset.
- Keep the headset dry.
For better using experience, Please scan to download QCY app before start-up
