QCY-T8 Bluetooth Earphone Semi-in-ear Wireless User Manual

QCY-T8 Bluetooth Earphone Semi-in-ear Wireless

OVERVIEW

How to Connect

First Time Pairing:

1.  Pick up both earbuds then re-insert them into the case. Once again, pick them up to activate them
2. On cellphone, search for QCY-T5 Pro and tap to Connect. “Once paired earbuds will auto power on upon picking up from the case. If earbuds fail to auto power on, please charge them and try again.

Switch Paired Device:

1.  Turn off phone’s Bluetooth faculty and earbuds will auto disconnect and enter into pairing mode
2.  On ohone8, search for QCY-T5 Pro and tap to connect. Multi-point connection is not available. Earbuds will auto-reconnect to phone B upon powering up again

Factory Setting

(Try the following steps to fix connectivity issue)

Set to factory:

1. On cellphone, search for QCY-T5 Pro, tap and choose ignore or cancel pairing
2.  Pick up two earbuds, keep touching both bars for 8s or until LEDs glow red for 2s to power off.
3.  Keep touching both bars for 10s or until LEDs blink red and green 3 times then blink red to set earbuds to factory Please refer “First Time Pairing” to connect after factory setting

Manual Pairing (please refer the following steps in case two earbuds lose connection) Power off earbuds then keep touching panels for 5s or unti LEDs blink red and green. After then, double touch panels and LEDs will blink red and green, Two earbuds will then auto pair with each other when LED on master earbud blinks red and green and the other one turns off.

HOW TO WEAR

1. Rotate earbud and pop it into your ear then shake head to check wearing stability.
2. Please adjust mic towards your mouth to gain better calling experience

Three-way Calling & Switch

Double touch the bar to answer incoming call. If another call is coming in sync, double touch again to put the first call on hold while activating the second one or kee touching the ba for 2s to ignore the second call. Keep touching the bar for 2s to switch between active call and held call.

Mono Mode

1. Power off earbud then keep touching the bar for 5s to enter pairing mode (LED blinks red and green)
2. On cellphone, search for QCY-T5 Pro
3. Tap to conne

Charging Earbud
Push earbud into the case to charge. LED will glow solid red when charging and turn to green for1 minute once top-up.

Charging the Case
When the power is less than 306, the two green lights of the charging box flash; when the power is between 30% and 90%, the left light is always on green, the right light is blinking; when the power is more than 90%, The two green lights on the charging case are always on.

FUNCTIONS

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hamíiul interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. I this equipment does cause harmiul interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Hazardous substances and their contents in the item

Tips

1.  Before using the headset, please read the manual carefully and keep it for future reference.
2.  The headset needs to be fully charged prior to first-time use.
3.  If the headset is left unused for over two weeks, please recharge it periodically.
4.  Please use the chargers made by a qualified manufacturer.
5.  If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; ifa procedure error of your phone occurs, reboot it; if a procedure error of the headset occurs, reboot or reset it

Caveats

1.  Never disassemble or modify your headset for any reason to avoid any damage and danger.
2.  Do not store the headset in extreme temperatures (under 0°C or over 45°C).
3.  Avoid using the indicator close to the eyes of children o animals
4.  Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electric shock.
5.  Do not use harsh chemicals or strong detergents to clean the headset.
6.  Keep the headset dry.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>