QCY IN2020L TWS Bluetooth earphones User Manual
- June 5, 2024
- QCY
Table of Contents
IN2020L TWS Bluetooth earphones
User Manualhttps://mapp.qcymall.com/qcyearphones/zh/download/qcy
For better using experience, please scan to download QCY app before start-up.
Overview
Choose Your Eartips
Please try medium eartips first as they fit most people.
How to Pair
First Time Pairing:
- Pick up both earbuds, pop both earbuds into the case to activate them.
- Pick up both earbuds again.
- On cellphone, search for QCY-HTC1 and tap to connect.
*Once paired earbuds will auto power on upon picking up from the case. If earbuds fail to auto power on, please charge them and try again.
Switch Paired Device
- Turn off phoneA’s Bluetooth faculty and earbuds will auto disconnect and enter into pairing mode.
- On phoneB, search for QCY-HT01 and tap to connect
*Multi-point connection is not available. Earbuds will auto reconnect to phoneB uphon powering up again.
Factory Setting
Delete pairing records
(please try the following steps if earbuds fail to connect)
- On cellphone, delete the connectivity records of QCY-HT01.
- Power off earbuds, hold MFBs for lOs or until LEDs blink red and white 3 times to set earbuds to factory.
- After factory setting, please refer How to Pair to build connection with cellphone.
How to Wear
- Rotate earbud and pop it into your ear then shake head to check wearing stability.
- Please adjust mic towards your mouth to gain better calling experience.
Three-way Calling & Swith
Press MFB to answer incoming call. If another call is coming in sync, press
MFB to put the first call on hold while activating the second call or hold
IvIFB to ignore the second call. Double press MFB to switch between held call
and active call.
Mono Mode
- Power off earbuds, keep touching M FB on either earbud for 5s to enter pairing mode (LED blinks red and green).
- On cellphone, search forQCv-HT01 and tap to connect.
- Connected.
Charging Earbud
Push earbuds into case and earbuds will auto be charged.
LEDs will glow solid red when charging and turn green for 1 minute once topped
up.
Charging the Case
Please charge the case via USB cable.
Battery level.600/0: LED blinks red
Battery level between 60% and 95%: LED blinks green
Battery level 950/0: LED blinks white
Top up: LED turns on solid white
Functions| Current status| Operation result| LED|
Prompt
---|---|---|---|---
Power-on| Power-off| Hold MFB fdr1.5s| LEDglows white for 1.5s| TONE
Charging| Pick up earMuds from case| LEDglows white for 1.5s| TONE
Power-off| Power-on| Put the hearthone into the box,
close the co .r and turn off the headset| Led glow red| TONE
Pull back into case
TONE
TWS pairing| First pairing following factory setting| 1. Lelft earbud will
auto turn conectable to phone upon pairing with the right one.
2. Eearbuds are auto power off if they fail to pair with each other in 5
minutes.| 1:11 blinks red andwillt| TONE
Answer/end call| Incoming call/calling| Double pre4s MFB| | TONE
Ignore call| Incoming call| Hold M FB kr is| | TONE
Voice assistant| Connected| Three pres1 left MFB| | TONE
FCC Statement| the headphones are out side the box| Long press MFB| The red
and white lights flash altsratdy three times| TONE
Music pause/ resume playing| Playing| Double pres’s MFB| | \
Skip track| Playing| I ong press fight MIR| | \
Switch call to earbud| Call handled by phone| Put on the headphone| | TONE
Switch call to phone| Call handled by earbuds| Take off thd headphone| | TONE
Warranty Card
Warranty Period
12 months after you purchase this itern.(or you may inquire your local
shopper for more details.)
Free Service:
Supposing any defects caused by quality issues occur within the warranty
period, please take this warranty card and purchase receipts to your
distributor for free exchange service.
Model Number:
Date of Purchasing:
User’s Name:
User’s Phone:
User’s Address:
Shop’s Name:
Shop’s Address:
Comments:
Free exchange service will not be accessed under following circumstances:
- Damages caused unauthorized disassembly.
- Defects or physical damages caused by leaking or dropping off.
- Damages by act of God.Supposing your item is within any damages ordefects except the above circumstances, please return to us or your distributor for free repairing.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC ID:RDR-IN2020L
FCC ID:RDR-IN2020R
Hazardous substances and their contents in the item
Part Name | Hazardous Substances |
---|---|
Pb | Hg |
DEHP | DBP |
Main body | X |
Battery | 0 |
Ear tips | 0 |
Arressor’ec | 0 |
Chargiig
cable| x| 0| 0| 0| 0| 0| 0| 0| 0| 0
This form is made by SJ/T 11364 regulation.
O: means that ha:ardous substance content in the homogeneous materials of this
part is within the limits of (EU) 2015/863 regulation .
X : means that hazardous substance content in ,at least, one certain
homogeneous material of this part is beyond the limits of (EU) 2015/863
regulation ,but there is no mature alternative in the industry at present, it
still conforms to the EU ROI-IS Directive in the scope of exemption.
Notes: Please arrange using time properly as your hearing may be damaged
by using the device for a long time.
Manufacturer: Dongguan Hele Electronics Co., Ltd.
Address: Daojiao Town, Dongguan City, Guangdong, China
Tips
- Before using the headset, please read the manual carefully and keep it for future references.
- The headset need to be fully charged prior to first-time use.
- If the headset is left unused for over two weeks, please recharge it periodically.
- Please use the chargers made by qualified manufacturer.
- If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please reenter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.
Caveats
- Never disassemble or modify your headset for any reasons to avoid any damages and
- Do not store the headset in extreme temperatures (under 0°C or over 45°C).
- Avoid using the indicator close to the eyes of children or
- Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electricshock.
- Do not use harsh chemicals or strong detergents to clean the headset.
- Keep the headset dry.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>