ZOSI C302 8-Inch 1080P Wireless Security System User Guide
- June 6, 2024
- ZOSI
Table of Contents
Quick Start Guide
wireless security Camera system
For more information of your new system, please refer to
www.zositech.com
Gallery and Specs
System Connection
Connect NVR to the Internet
- Connect NVR to the router using a network cable.
- Connect the monitor to NVR via HDMI or VGA port.
- Connect the included USB mouse to the top USB port of NVR.
- Connect NVR to 12V power supply.
- After the system starts, pair and connect IPC and camera to the system (maximum support 8 channels).
- The monitor will show the real-time monitoring picture of the camera
B: How to test the network status of NVR?
- Right-click Mouse > Go to Main Menu > Setting > Network
- Tick ‘Obtain IP address automatically’ Click ‘Test’, if ‘OK’ is displayed, tick `DHCP’ and apply, the device will automatically assign the corresponding network segment and IP address. After clicking Test, if the page is displayed successfully, it is successfully connected to the network.
NOTE : Please make sure that the DHCP of the connected router is enabled at the same time.
C: WiFi Setup
Right-click the main interface – Main Menu – Setup – Network – Wireless
Network, default setting and apply.
Download Zosi Samart App 2.3 Run the App
A: Install the free Zosi Smart App. B: Click Register and enter your email box to get the verification code, click next to set up a password and save it, registration is completed. C: Log in the App, get into the main interface (My Device), click”-F” in the upper right corner to add devices. D: Select ‘DVR’ – ‘Wireless recorder’ E: Go back to the Device list > Tap the device > Tap “+” to select the channel (all selected) > Tap Confirm to start live streaming.
2.4 2-Way Audio
Support two-way voice intercom through Zosi Smart APP. The camera microphone
is at the upper right corner of the lens, the speaker is at behind the camera.
NOTE: You will receive low-battery notification via App when battery power is
less than 20%. 
AVSS PC Client
3.1 Install AVSS on PC
Get the AVSS software from www.zositech.com or from
your agent. Double-click the icon AVSS to open, select the language, and click
Login. Note: You can log in with the default username and password, or
register a new account. The user name is the account and password registered
on the App in 2.3. 
3.2 Device Management Click the Add Device button in the device list to
add/edit/configure/search for the device. 
3.3 Live View
Select a channel to watch live streaming.
3.4 Video Playback
Select ‘Playback’, select device, channel, date, time, click the play button
to start replaying the recorded video. 
Add Device
4.1 Add IPC to the wireless camera system
(1) Connect IPC and NVR in the same wireless network.
(2) Right-click the mouse on the live channel page and get the main menu.
(3) Click IPC Channel Config to enter the configuration page.
(4) Click the search button to search for IP cameras.
(6) The IPC device is successfully added and it can be
displayed in the live view channel and operated.
(6) The IPC device is
successfully added and it can be displayed in live view channel and operated.
- Power off the NVR, unscrew and remove the top cover of the recorder.
- Connect the power cable and data cable of the hard drive to the corresponding ports in the recorder. (As shown in the figure).
- Put the hard disk in the recorder. All wires should cross up over the hard drive. ®
- Hold the hard disk and the NVR, gently turn it over and line up the holes on the hard disk with the holes on the NVR. Use a Phillips screwdriver, screw the included screws into the holes. Assemble the cover. ®
- Insert the Micro SD card into the card slot on the recorder. You need to format the hard drive or Micro SD card before recording Steps: Right-click mouse> Main Menu>
- Hard Disk Management> select the Hard Disk> Format> Apply
NOTE: It can only support either a Micro SD card or hard drive storage at one time.
Video Record
Right-click the mouse > Go to Main Menu > Setup > Record You shall see the
record settings for all channels. Modify the record set based on your needs
and apply the changes.
6.1 Motion Detection
Set motion Detection, NVR will only record when motion or movement is
detected. Right-click the mouse > Main Menu > Setup > Alarm > Motion
detection. The system starts recording when motion is detected by the camera,
and the captured picture will show at the bottom left corner. Select camera:
tick the channel you want to record on motion detection.
6.2 Human-form Detection
The system can trigger alarms and record when human-form is detected. Motion
detection and human-form detection can significantly reduce false
alerts.
6.3 Siren and Light Alarm
You can set up a siren and light alarm. Five alarm modes: strong siren and
light alarm, light siren and light alarm, strong siren alarm, a light siren
alarm, and strong light alarm. Three Night vision modes: full-color night
vision, black and white night vision, and smart night vision. You can freely
switch three-night vision modes. Three alarm types: motion detection, human-
form detection, and motion detection plus human-form detection.
6.4 Video Playback
Go to Main Menu > Search, the system presents as follows:
Search the video you want by time or event to play.
Previous Record: move to
last recorded event Next Record: move to next recorded event Fast Forward:
video can be played at different speeds, from 1/4 times to 16 times. Rewind:
Video play can be rewinded at 1 time, 8 times, 16 times, and 32 times. Screen
Display Mode: both single-screen and multi-screen are available. You can
choose how many channels you want to play back at the same time. Channel
without records presents a blank screen.
6.5 Video Backup Insert
USB flash drive> right-click the mouse> enter the Main Menu> Hard Disk
Management> USB flash drive detected> return> Backup> select Channel and Time
period> Search> select the video file you want to back up> click Backup>
backup complete.
Live Video Display
You can see a picture display on the monitor normally. as the 4′ channel picture owns in tho figure.
FAQs
Q: Why can’t I search for devices when adding cameras?
A: Make sure that the device and the mobile device are on the same LAN,
otherwise please enter the device ID manually.
Q: Why can’t my device connect to the network?
A: Please check:
• Is the device connected to the Internet?
• Is the router working properly?
• Is the router’s DHCP server open?
Q: Why can’t I find the video files?
A: Please check:
• Is the hard drive broken?
• Is the search period valid?
• Whether the system time is correct.
Q: Why the monitor screen cannot display some channels?
A: Please check whether the camera has been added to NVR.
Q: Why can’t I watch the recording by entering the device password?
A: Please confirm whether the correct device password is entered. It is
recommended to keep the password.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>