CALIBER RCD 234DAB-BT Car Auto Radio Instruction Manual

: June 17, 2024
: CALIBER

CALIBER RCD 234DAB-BT Car Auto Radio

Product Information

Specifications

Type of disc: CD, MP3, WMA
Label on the disc: Audio only
Recorded material: 12 cm

Precautions

DO NOT ATTEMPT TO MODIFY THE UNIT, MODIFYING THE UNIT MAY CAUSE AN ACCIDENT.
STOP THE VEHICLE BEFORE CARRYING OUT ANY OPERATION THAT COULD INTERFERE WITH YOUR DRIVING.
DO NOT TURN ON THE UNIT IF THE TEMPERATURE INSIDE THE VEHICLE IS OUT OF -20’C TO 60’C.
Clean the discs with a cleaning cloth.
Don’t use CDs with blobs of glue or ink on its surface.
Clean each disc from the center to the outside edge.
Don’t use CDs with label or stickers on its surface. There could be some remainder of glue which would interfere with the good performance of the unit if labels were starting to be rubbed away.
Hold and handle discs by the edges to keep them disc clean and don’t touch its surface.

Warnings Before Installation

Damage Caused By Incorrect Installation or Usage is NOT Covered By Warranty.
Please take the time to read the installation notes carefully.
A good chassis ground requires a tight connection to the vehicle’s metal chassis.
The area around the ground connection should be clean, bare metal without rust, paint, plastic or dirt for a good electrical connection.

Tools for Installation
Tools for Installation:

Philips Screw-drivers
Wire Stripper
Wire Cutter
Hammer
Pencil
Electrical Tape
Electric Drill

Supplies for Installation:

Machine Screws
Crimp Connectors
14 Gauge Wire for Power Connections
14-16 Gauge Speaker Wires *
The above are not supplied.

Before You Install
Automotive audio equipment installations can be troublesome at times, even to the most experienced of installation technicians. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other
components of your vehicle, please call your dealer in order to have the unit professionally installed.

IMPORTANT: Remove the two transport screws from the top of the unit before installing.

Product Usage Instructions

Step 1: Remove the Old Unit from the Dashboard

Remove the outer trim frame.
Insert the keys supplied with the old unit into both sides of the unit as shown in the figure below until they click.
Pull to remove the old unit from the dashboard.

Step 2: Mark Polarity of the Speaker Wires
Marking the polarity of the speaker wires will make it easier to connect the existing speakers to your car radio. Consult the wiring diagram of the existing head unit before disconnecting any wires. If you are not positive of the polarity of the existing wires from the speakers to the head unit, install new wires.

While the old unit is playing, disconnect the wires from one speaker.
Take a length of masking tape and fold it around the wire so it forms a flag.
On the masking tape, mark the polarity of the speaker wires (+ & -), as well as left or right, and front or rear.

FAQ

Q: What types of discs are compatible with this unit?
A: This unit is compatible with CD, MP3, and WMA discs.

Q: How should I clean the discs?
A: Clean the discs with a cleaning cloth. Do not use CDs with blobs of glue or ink on their surface. Clean each disc from the center to the outside edge. Do not use CDs with labels or stickers on their surface as they could interfere with the unit’s performance.

Q: What precautions should I take when using this unit?
A: Do not attempt to modify the unit as it may cause an accident. Stop the vehicle before carrying out any operation that could interfere with your driving. Do not turn on the unit if the temperature inside the vehicle is out of -20°C to 60°C. Hold and handle discs by the edges to keep them clean and avoid touching the surface.

Precautions

This unit will only play the following discs.

DO NOT ATTEMPT TO MODIFY THE UNIT, MODIFYING THE UNIT MAY CAUSE AN ACCIDENT. STOP THE VEHICLE BEFORE CARRYING OUT ANY OPERATION THAT COULD INTERFERE WITH YOUR DRIVING. DO NOT TURN ON THE UNIT IF THE TEMPERATURE INSIDE THE VEHICLE IS OUT OF -20’C TO 60’C.
This unit only reads 12 cm discs. Don’t attempt to modify the unit; it could result in an accident. Stop the vehicle before any manipulation that could interfere with your driving. Do not use the unit if the temperatures are extremely cold or extremely high (lower than -20° or higher than +60°). To enjoy a sound of best quality, handle discs as indicated below:

Clean the discs with a cleaning cloth. Clean each sisc from the center to the outside edge
Don’t use CDs with blobs of glue or ink on its surface.
Don’t use Cds with label or stickers on their surfaces. There coule be some remainder of glue which would interfere with the good performance of the unit if labels were starting to be rubbed away.
Hold and handle discs by the edges to keep the disc clean and don’t touch its surface

Warnings Before Installation

Important Warnings to Take Note of BEFORE Commencing Installation Damage Caused By Incorrect Installation or Usage is NOT Covered By Warranty. PLEASE Take The Time To Read The Installation Notes Carefully.

To avoid shorts in your vehicle’s electrical system, be sure to disconnect the battery cable before beginning installation.
This unit is intended for vehicles with a 12-volt battery and negative grounding. Before installing the unit in a recreational vehicle, truck, or bus, check that the battery voltage is 12 volts.
Remove the two transport screws from the top of the unit before installation.
The black lead is ground. A good chassis ground requires a tight connection to ground. The area should be free from rust, paint or any form of dirt. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.
Be sure to connect the color-coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle’s electrical system. Cords for this prod-uct and those for other products may be different colours even if they have the same function. When connecting this product to another product, refer to the supplied installation manuals of both products and connect cords that have the same function.
Be sure to connect the negative (-) speaker leads to the negative (-) speaker terminal. Never connect the negative (-) speak-er leads to chassis ground.
The unit is only designed for use with 4 speakers. Do not combine outputs for use with 2 speakers. Do not ground negative speaker leads to the chassis ground.
Speakers connected to this unit must be high-power units with a minimum rating of 45W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here will result in damage to the head unit and the speakers. Check the condition of your speakers carefully- connecting this unit to old or degraded speakers may result in a fault that will damage the audio IC and invalidate the warranty.
If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with the ignition switch ON/Off operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours.
Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. To avoid short-circuiting, cover all disconnected lead with insulating tape. There is a possibility of short-circuiting if the leads are not insulated.
Route and secure all wiring so it cannot touch any moving parts, such as the gear lever and handbrake. Do not route wir-ing in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle’s body.
Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead’s insulation and cause a very dangerous short.
Do not shorten any leads. If you do, the protection circuit may fail to work when it should.
Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.
When this product’s source is switched ON, a control signal is outputted through the orange lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.
When an external power amp is being used with this system, do not connect the orange lead to the amp’s power terminal. Likewise, do not connect the orange lead to the power terminal of the auto-antenna. Such a connection could cause excessive current drain and a major malfunction. Refer to the relevant owner’s manual for details on connecting the power amp and other units, then make the connections correctly.
Do not block any vents or heater panels. Blocking them will cause heat to build up and may result in fire.
Make sure that the unit has a good chassis ground. A good ground connection will eliminate most electrical noise. A good chassis ground requires a tight connection to the vehicles metal chassis.
The area around the ground connection should be clean, bare metal without rust, paint, plastic or dirt for a good electrical connection.
If noise is still experienced when the motor of the vehicle accelerates, a choke should be placed in line with the power to the unit. The installation company will know what is required.
When replacing the fuse(s) the replacement must be of the same amperage as shown on the fuse holder. Never replace a fuse with another of a different value. If the fuse blows again please contact your installation company.
Do not block vents or heater panels. Blocking them will cause heat to build up inside and may result in fire.
Double-check that all wiring and connections are correct before re-connecting the battery and turning on the unit.
After completing the installation and before operating the unit, reconnect the battery, Then press the (RES) button with a pointed object, such as a ball-point pen to set the unit to its initial status. After pushing the button, wait a few seconds for the red light to flash.

Tools for Installation

2 removal wrenches are supplied for taking out the old unit and place with this brand-name car radio. The following tools and supplies may also be needed for the installation:

Tools for Installation:
- – Philips Screw-drivers
- – Wire Stripper
- – Wire Cutter
- – Hammer
- – Pencil
- – Electrical Tape
- – Electric Drill
Supplies for Installation:
- – Machine Screws
- – Crimp Connectors
- – 14 Gauge Wire for Power Connections
- – 14-16 Gauge Speaker Wires
The above are not supplied.

Before You Install

Automotive audio equipment installations can be troublesome at times, even to the most experienced of installation technicians. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed.

IMPORTANT : Remove the two transport screws from the top of the unit before installing.

Remove the Old Unit from the Dashboard

Remove the outer trim frame.
Insert the keys supplied with the old unit into both sides of the unit as shown in the figure below until they click. Pull to remove the old unit from the dashboard.

Mark Polarity of the Speaker Wires
Marking the polarity of the speaker wires will make it easier to connect the existing speakers to your car radio.Consult the wiring diagram of existing head unit before disconnecting any wires. If you are not positive of the polarity of the existing wires from the speakers to the head unit, install new wires.

While the old unit is playing, disconnect the wires from one speaker
Take a length of masking tape and fold it around the wire so it forms a flag.
On the masking tape mark the polarity of the speaker wires (+ & – ), as well as left or right, and front or rear.
Double-check that you marked the first speaker correctly by checking that the speaker wires are the same at the head unit.
Repeat this procedure for all of the speakers.
Mark the power, ground, and any other wires also.

Installation

WARNING!
Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions.

NOTE : Mark the polarity of the existing speaker wires before disconnecting battery.

NOTE : Remove the two transport screws from the top of the unit before installing.

DIN Front Mount

After removing the old radio and mounting sleeve, insert the supplied mounting sleeve into the opening.
Bend the tabs on the mount-ing sleeve to keep the mount-ing sleeve firmly in place.
Attach wires from the unit to existing wires. See wiring con-nections diagram. Insert radio into dashboard. Then apply the trim frame to outside of radio.
Support radio using sup-plied rear mounting bolt and steel bar. See parts list.

NOTE : Outer trim frame, hook, and mounting sleeve are not used for this installation.

This is only intended as a general guide; contact the vehicle’s manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket.

Remove the hooks on both sides.
Align the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit. Tighten the 2 screws on each side of the unit. Then fasten the brackets to the car.
Attach wires of the unit to the existing speaker wires. See wiring diagram.

Wiring Connections

Make sure that you have a good chassis ground. Good ground connections will eliminate most electrical noise prob-lems. A good chassis ground requires a tight connection to the vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good electrical connection.

Connector A

Rear right speaker(+)/Purple
Front right speaker(+)/Grey
Front left speaker(+)/White
Rear right speaker(-)/Purple-Black
Front right speaker(-)/Grey-Black
Front left speaker(-)/White-Black
Rear left speaker(+)/Green
Rear left speaker(-)/Green-Black

Connector B

–
–
–
Battery 12V (+)/Yellow
Antenna power/Blue-White
Panel light/Orange-White
ACC+/Red
Ground/Black

Black Ground
Connect to vehicle body/chassis. Make sure that you have a good chassis ground. This will eliminate most electrical noise from the motor and alternator. A good chassis ground requires a tight con-nection to ground. The area should be free from rust, paint or any form of dirt.

Yellow Memory backup
Connect to electrical terminal always supplied with power regardless of ignition switch position.

Orange Remote
Connect to Auto-antenna or power amp control wire/remote con-nection. Maximum current 300Ma 12 V DC.(Low Current)

White Panel Light
Connect to the lighting circuit of the vehicle. This will illuminate the buttons on the display for nighttime operation. This wire can also be connected to the Orange Remote wire to activate the buttons when the unit is powered on. DO NOT JOIN THE WHITE WIRE TO THE LIGHTING CIRCUIT OF THE VEHICLE IF CONNECTED TO THE ORANGE REMOTE WIRE.

Speaker Wiring Notes
Follow the above wiring diagram to install the head unit with new or existing speakers.

This unit is designed for use with four (4) speakers with impedance between 4 Ohms to 8 Ohms.
An impedance load of less than 4 Ohms could damage the unit
Never bridge or combine the speaker wire outputs. When not using four speakers, use electrical tape to tape the ends of the unused speaker outputs to prevent a short circuit.
Never ground the negative speaker terminals to chassis ground.

Basic Operation

Tuning the unit On / Off
Press PWR Button to turn the unit on, the display will show a message WELCOME to indicate it is ready for use. Press and hold the PWR button to turn the unit off. The display will show the message “GOODBYE”.
Mode Selection
Press the MOD Button to select Radio Mode. Press the MODE Button to cycle the Play Mode amoung AUX, RADIO and CD PLAY.
Note: USB & SD mode will only show on the display when a USB flash memory or SD card is inserted into the USB port or SD portt.
Loudness Control
Press the SEL button until “LOUD OFF” is shown on the display indicating that the loudness function is OFF. Turn the volume knob to select between ON or OFF.
Mute Control
Press the POW/MUT button active or cancel Mute function.
Volume
Use the VOL +/- Button to adjust the volume level. The larger the number, the higher the volume level.
Treble
Press SEL Button repeatedly until the display shows “TRE 00”. Use the VOL+/- Button to adjust. When EQ is ON, treble control is not available.
Balance
Press SEL Button repeatedly until the display shows “BAL L-R”, then use the VOL +/- Button to adjust the balance between the left & right speakers.
Fader
Press SEL Button repeatedly until the display shows “FAD F-R”, then use the VOL +/- Button to adjust the balance between the front & rear speakers.
Clock
The time clock can be set anytime when the power is on. Press the PTY/CLK Button on the faceplate or remote control once, the time will show on the display.
Then press and hold the button until the hour blinks on the display. Rotate the VOL knob to set hours, then press the VOL knob for the minutes to blink and rotate the VOL knob to set. Press the PTY/CLK button again or leave the unit idle for new setting to effect. Press the PTY/CLK button anytime to view the time clock display.
Preset Beep Sound Off
Press the SEL button repeatedly until “BEEP ON” is displayed. Turn the VOL +/- Button to select “BEEP OFF” or “BEEP ON”, then leave the unit idle for setting to take effect.
Preset Equalizer Function
Press the SEL Button repeatedly until “EQ” indication is displayed then rotate the Volume knob to choose between the EQ sound effects. The Sequence of equalizer setting will be as follows:

Radio Operation

Choose Radio Band
Press the BND Button anytime to access the radio function. The unit comes with five bands- three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations.
Radio Tune / Seek Function
In Radio Mode, press and hold the “>>| ” or “|<<“, manual seek will be activated and the radio frequency will proceed by one step.Press the SEEK |<< or >>| Button once, and the radio will seek the next strong and clear frequency station. Repeat to seek more stations in your listening area with a strong signal.
Mono / Stereo Reception Control
In FM radio mode, Press SEL But-ton repeatly until the display shows ‘MONO’ or “STEREO”. Roate the Vol button to choose the reception control, the word “MONO” shown on the screen indicating the mono reception is received.
Save Your Preset Stations
There are six numbered preset but-tons which can store and recall stations for each band. While listening to a radio station you would like to save as a pre- set, press and hold one of the buttons numbered 1-6 until the preset station number is shown. The button you pressed is now the pre-set button for that station.
Automatic Store / Preset Scan
Automatic Scan & Store
While listening to the FM Radio, press and hold the F/PS Button for 3 seconds. The receiver will automatically scan and save the station listening to. While listening to the AM Radio, press and the F/PS Button for 3 seconds. The receiver will automatically scan and save the station you are listening to
Scan Saved Stations
Press the F/PS button once to perform the scanning functions. In FM mode, press the F/PS button and the stations in that FM band will be scanned; press the button in AM mode and scan the band stations of that AM Band
Local / DX
Press SEL Button repeatly until the display shown “LOC”. Rotate the VOL button to choose “LOC ON“ or “LOC OFF”.
“LOC ON” showing on the display, means local reception is turned on;
“LOC OFF” showing on the display, means distant reception is turned on. Local and distance reception settings can facilitate the radio reception, depending on the location in which the radio is being used.
DAB Function
This device is equiped with DAB function. Press MOD to cycle to DAB mode. Press F/PS to scan all the radio stations. When a station is listed, press BND to show the following information of the station:
Name;
Type;
Code information;
Frequency;
Date;
Signal strength.
Long press the Volume knob to show the DAB time synchronization with the system.

RDS Operation (Optional)

RDS Function
RDS ( Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either.

AF-ALTERNATIVE FREQUENCY
In RDS mode, press the AF button on the panel to turn the AF function on or off. When the Radio signal strength is poor, enabling the AF function will allow the unit to same PI (Program Identification) as the current station but with stronger signal strength, so that you do not have to retune the stations when driving between different transmitter coverage areas. When AF symbol is on, it means RDS information is received; when AF symbol is flashing, it means RDS information is not yet received. PS (Program Service name): the name of statin will be display instead of frequency. If RDS service is not available in your area, turn off the AF mode. Dufault setting is ON.
In RBDS mode, no AF function.
TA – TRAFFIC ANNOUNCEMENTS
Press and hold the TA button so that the unit will be activated for reception of traffic announcements from local ra-dio stations. To choose the TA mode, press the sound select button for 2 seconds, the display will show TA SEEK. Rotate the encoder volume to choose between the TA SEEK and TA ALARM, after chooisng, please leave the unit idle for the mode to activate. In TA SEEK mode, the unit will seek for traffic announcement programme when TA is pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off.
PTY – PROGRAMME TYPE
This radio will allow you to select the type of program required and will search for a station broadcasting that type of programme. Press and hold the PTY button once to show the music type. Then press 1-6 button to choose the different music types available. Press the PTY button twice to show the speech type programme. Then press 1-6 button to choose the differ-ent speech type programme. Each number keye will show 3 different speech programme for you to choose.
MASK DPI – MASK ALL
Press the sound select button for 2 seconds, the display will show TA SEEK. Press the sound select button again so that the unit will show MASK DPI. Rotate the encoder volume to toggle between MASK DPI and MASK ALL mode. Then leave the unit idle for the mode to take effect. During MASK DPI mode, the unit will mask only the AF which has different PI, this is the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal with high field strength.
RETUNE S/L – SHORT/LONG
This function is to set the initial duration of automatic TA Search — Press and hold the sound select button until “TA SEEK” is shown on the LCD, then press the SEL button to cycle through the menu selections until “RETUNE_S” is shown, use the VOL+/- button to choose “RETUNE_S” or “RETUNE_L”. The default is “RE-TUNE_S”.
TA VOL
This function is to set the TA volume, the default level is 25.

Bluetooth Operation

Pairing
The bluetooth of this radio is always in standby mode for pairing and connec- tion, signalled by a blinking bluetooth icon on the LCD Display. At this blinking time, please run the bluetooth search and connect function in your cellphone. The car radio model no “RCD234DBT Caliber” will be shown on the cellphone. Select this car radio and connect to finish the pairing. The bluetooth icon on the display will be on indicating that the connection is established. Bluetooth function is ready to use. * A pairing password is required in some phones. Insert “0000” in such case.
Calling
In any play mode, dial the desired number on your cellphone. The unit will switch to bluetooth hands-free mode automatically. “CALL OUT” will be shown on the display indicating the dialling is in progress.
Accepting Calls
When there is an incoming call, “CALL IN” will be shown on the display indicating there is phone call to answer. “BT TALK” will be shown after the “ANSWER” button is pressed. Rotate the volume knob during ringing or conversation to adjust the respective volume level.
Rejecting Calls
During ringing or conversation, press the “REJECT” button to end the call or reject the call. the unit will resume to the original play mode.
BT Audio (A2DP)
Press MOD/ button until the unit entered BT AUDIO. BT audio will play automatically when you play the song in the cellphone. You could pause by button, to choose the previous or next song by pressing |<< and >>| button.
Disconnecting
Disconnect the paired phone by operating on the cellphone. You cannot process disconnection on the car radio headunit.

CD/MP3/WMA/USB/SD Operation

Insert / Eject CD
Insert a disc into CD slot with label side up. The disc will be automatically loaded into the unit, even when it is off or at radio mode. The word “LOAD” will blink on the display and the CD will play automatically. Press the EJECT Button to eject the disc from the slot. If the disc is not removed from the slot within 5 seconds, it will automatically be loaded into the slot again. When the disc is ejected and removed, the unit will automatically switch to radio mode. While you are playing a disc with MP3 or WMA, The first file in the root folder will be played. if there is any ID3 information that will be displayed as the file is playing. To play MP3/WMA files from a USB flash memory or SD card, insert a USB flash memory or SD card into the USB port or SD port of the unit. The unit will start playing MP3/WMA files on the USB flash memory automatically. If the MP3/WMA files are stored in folders on the USB drive, the unit will start by playing the first song in the first folder. After playing all the files sequentially in the first folder, the unit will play sequentially all of the files in the next folder. The unit will continue playing through all of the folders on the USB drive in this manner. If the USB drive has loose files and folders containing files, it will play the loose files sequentially, then it will play the files in the folders sequentially.
Multi-Session CD Reading
This unit can read multi-session CDs. The multi-session reading will be activated automatically if the player detects a file that is written in multi- session format.
Selecting Tracks
Press the SEEK >>| Button to advance CD to the next track. Track numbers will be shown on the display. Press and hold SEEK >>| to fast forward. Press the SEEK |<< Button to go to a previous track. Track numbers will be shown on the display. Press and hold the SEEK |<< Button to fast reverse. Disc will play normally when the No. 1(play/pause) Button is pressed.
Play / Pause CD
Press the No.1/PAU Button to pause the CD. Press this button again to resume playback.
Scanning Tracks
Press the No.2/INT Button to play the first 10 seconds of each track, “INT” will be displayed on the display. Press this button again to resume playback.
Repeat
Press the No.3/RPT Button to repeat the current track. Press it again to cancel.
Random
Press the No.4/RDM Button to play all the tracks in random order. “RDM” will appear on the display. Press this button again to stop random play.
Folder Down
Press the “ 5 button once to go back to one folder.”
Folder UP
Press the “6 ” button once to advance one folder.
Search Modes
There are 3 search modes to help find your favorite MP3 & WMA tracks. The search modes only works with MP3/WMA CDs, and USB flash memory with MP3/WMA files.
Simple Track Search
Press the SEEK |<< or >>| Button to go to the next track or previous track.
Track Search
Press the F/PS Button, and TRK-SCH will appear on the display. Use the VOL+/- Button to select the track number. press the SEL button so that the chosen track will start to play.
Folder Search
Press the F/PS Button twice and NAVIGATE will be shown on the display. Use the VOL +/- Button to select the folder name. Then press the SEL Button to play the chosen folder.
Electronic Skip Protection
Electronic Skip Protection is for driving on rough roads. The CD will play for 10 seconds on rough roads without skipping. if driving on a rough road for more than 10 seconds the CD may skip. For MP3 or WMA files will play for 60 seconds. If the road is rough for more than 60 seconds the CD with MP3 or WMA files may skip.

ID3 Tag

While you are playing an MP3 file that has ID3 Tag information, Press BND/ID3 button repeatedly to show the ID3 Tag information on the LCD. The ID3 Tag information will be as follows:
Fold – File – Title – Artist – Album If there is no ID3 Tag information, nothing will shown on LCD.

MAINTENANCE

Cleaning the Unit

Do not use any liquids to clean this unit.
Do not use petroleum distillates to clean this unit.
Use a clean, dry cloth to clean this unit.

Replacing the Fuse
Make sure the amperage matches the specified value when replacing the fuse(s). If the fuse is bad, check the power connection and replace the fuse with a new one. If the same problem occurs, this might indicate a malfunction within the unit.

Warning
When replacing a fuse, do not use a fuse with a higher amperage rating than the fuse originally supplied to your unit, otherwise, damage will result to your unit.