Enerlites 975547-C Stainless Steel Floor Box w TRWR Single Outlet Instruction Manual

Enerlites 975547-C Stainless Steel Floor Box w TRWR Single Outlet

Product Information

The product is a Single Gang Floor Box with a tamper-resistant 20A Single Receptacle. It includes an FB-06 box, gasket, and cover plate. The dimensions of the floor box are as follows:

• Overall Dimensions: 4-1/4″ x 3-1/4″ x 2-7/8″ (107.2mm x 83.3mm x 73mm)
• Cover Plate Dimensions: 3-5/16″ x 5″ (83.5mm x 127mm)
• Box Depth: 1-15/16″ (49.2mm)

Product Usage Instructions

• Before Installation:
  • Ensure there is sufficient depth and space below the subfloor.
• Step 1: Carpeted Floors
  • Cut out a section of carpet smaller than the size of the cover.
• Step 2: Floor Box Installation
  • Turn the POWER OFF at the circuit breaker before installing the Floor Box.
  • Read and understand the instructions before installing.
  • This device is intended for installation by the National Electric Code and local regulations. It is recommended that a qualified electrician perform this installation.
  • Make sure to turn off the circuit breaker or fuse(s) and ensure the power is off before wiring the device.
  • Use copper wire only.
  • Rout 3/8″ (10.16mm) deep for outer tabs.
• Wiring Directions:
  • Connect the HOT wire to the BLACK wire.
  • Connect the NEUTRAL wire to the WHITE wire.
  • Connect the GROUND wire to the GREEN wire.
• Warranty Information
  • This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
  • To claim a warranty, the original receipt or proof of purchase from an authorized retailer must be presented.
  • All claims must be verified and approved by Enerlites, Inc.
  • This warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation.
  • Enerlites’ liability is limited to repair, replacement, or refund as the sole and exclusive remedies for breach of warranty or any other legal theory.
  • For more information, visit www.enerlites.com
  • Product Code: 0309220193
  • Revision: 20230802

SPECIFICATIONS

Cover Material

• 975547 ………………………………………………………………………………..Brass(C) or Stainless Steel(SS)
• Receptacle Rating …………………………………………………………………………………………..20A 125VAC
• Box Material ……………………………………………………………………………………………..Galvanized Steel
• Knockout size ……………………………………………………………………………………………………………..1/2″
• Adjustable Height ………………………………………………………………………………………….up to 1″ depth

DESCRIPTION/ FEATURES

Included is a One gang floor box with a tamper-resistant 20 amp single receptacle, FB-06 box, gasket and cover.

• Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Stainless Steel (SS).
• Corrosion-resistant hardware ensures a long life span and reliable performance. Easy access to power when you need it.
• Used for carpet and wood floors.

WARNING

• Turn the POWER OFF at the circuit breaker before installing the Floor Box.
• Read and understand these instructions before installing.
• This device is intended for installation per the National Electric Code and local regulations.
• It is recommended that a qualified electrician perform this installation.
• Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only.
  • NOTES: 10-12 AWG Stranded or Solid Copper wire is recommended.

DIMENSIONS

FLOOR BOX INSTALLATION

Before Installation:

• Ensure there is sufficient depth & space below the sub-floor.

Step 1

• For carpeted floors:
  • Cut out a section of carpet smaller than the size of the cover.
• For wood sub-floors:
  • Tape the template on the area you want to place the floor box.
  • Use a knife to cut the outline of the box. Start with the ears and move inwards.
  • Following the outline, cut the box shape without the ears completely through the subfloor or hardwood floor.
  • Following the outline, cut 3/8″ deep into the subfloor for the mounting ears.
  • DO NOT ROUT OUT THE FINISHED FLOOR.

Step 2

• Remove knockouts and secure the box onto the floor. Pull the wires through the opening of the floor and the knockout and connect the wires based on the wiring  diagram
• Use the proper connector/ clamp at the knockouts to secure the wires and avoid accidental wire stripping.
• Secure the box to the opening using wood screws.

WIRING DIRECTIONS

1. Connect the HOT wire to the BLACK wire.
2. Connect the NEUTRAL wire to the WHITE wire.
3. Connect the GROUND wire to the GREEN wire.

WARRANTY INFORMATION

• This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
• An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim.
• ALL  claims must be verified and approved by Enerlites, Inc.
• Warranties from other Enerlites products may vary.
• This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation.
• To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end-user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages.
• Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement, or refund.
• Repair, replacement, or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.

CONTACT

• © 2022 Enerlites Inc.
• CA, U.S.A.
• WWW.ENERLITES.COM.
• 0309220193
• REV 20230802
• 975547-C & 975547-SS
• Single Gang Floor Box with 20A Single
• Tamper Resistant Receptacle

References

• Manufacturing Lighting Controls & Wiring Devices - Enerlites

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>