Connects2 CAM-42 Wide Angle Universal Brake Light Camera User Manual
- June 6, 2024
- Connects2
Table of Contents
Connects2Vision
User Manual
CAM-42
Wide Angle Universal Brake Light Camera
2-in-1 Reversing Camera/Brake Light Solution with Wireless Controller
PRODUCT FEATURES:
Image Sensor: 1/4”
TV Lines: 480
Resolution: 720 x 480
Minimum Illumination: 0.1 Lux
TV System: NTSC
Waterproof Rating: IP67
Viewing Angle: 210 Degrees (Horizontal) 140 Degrees (Vertical)
Parking Lines: Yes (Removable)
Image Adjustment: Yes (up to 5 different viewing modes)
Enhanced Performance In Low Light: Yes
Operating Voltage: 12-24V DC (Negative Ground)
Operating Temperature: -20 Degrees C to +75 Degrees C
DISCLAIMER:
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for
installation.
The place of installation must be free of moisture and away from heat sources.
Please ensure you use the correct tools to avoid damage to the vehicle or
product.
Connects2 can not be held responsible for the installation of this
product.
Technical Support
Connects2 want to provide a fast and suitable resolution should you encounter
any technical issues. With this in mind, when contacting Connects2, try to
provide as much information as possible. This will speed up the process and
help us to help you.
Please use our dedicated online technical support
centre:support.connects2.com
INSTALLATION
Wiring Diagram
| 1 | Red | Acc 12V | Connect to vehicle 12V Accessory feed |
|---|---|---|---|
| 2 | Black | Ground | Connect to the source of ground |
| 3 | Green | Reverse Output | Connect to aftermarket radio reverse trigger input |
| 4 | Purple | Reverse Trigger | Connect to vehicles reverse light for reverse gear |
trigger*
5| Blue| CAN +| Connect to the rear of the OBD connector (see diagram on Page
3)
| White| CAN –| Connect to the rear of the OBD connector (see diagram on Page
3)
* This wire is only needed if you are not using the white/blue CAN data wires.
Vehicle Connection Overview
Connecting CAN-Bus Wiring
Locate the vehicle’s OBD port and unscrew/remove the female connector.
On the reverse of the connector (the side where wiring enters it), connect the
CAN + (blue) and CAN – (white) wires from the harness to the locations
specified in the diagram (Pins 1 and 9).
USING THE WIRELESS CONTROLLER
Start-Up
The wireless controller included in the kit can be used to change the
viewing mode of the camera, as well as adjust key parameters for each viewing
mode .
To bring up the HUD menu, put the vehicle into reverse gear and press A.
Note: The HUD menu will time out after 3 seconds to allow an uninhibited view of the camera image. Press the A button to bring the HUD menu back onto the screen
The currently selected viewing mode is displayed by the icon in the centre of
the HUD menu. This will default to Driving/Rear-View mode, or to Reversing
mode when in reverse gear.
To change the camera mode, whilst the vehicle is in reverse gear, press B or C
to cycle through the Reversing, Wide Angle and Birds-Eye viewing modes.
Viewing Modes
Adjusting Settings
To adjust settings for all viewing modes, press A from the HUD menu to enter
the settings menu.
Once in the settings menu, short press A to cycle through the various settings
screens available. Screens include camera angle and position for each mode and
guideline width for parking lines.
Once in a settings screen, the selected setting is indicated by the icon in
the centre of the display. The parameters can be adjusted with B and C.
To return to the previous screen, press and hold A.
Activating/Deactivating Blind Spot View (BSV) Mode
When in any of the settings screens, a long press of B will activate or
deactivate BSV (Blind Spot View).
When active, this will trigger the blind spot camera image when an indicator
is activated and the vehicle is moving at a speed of over 40km/h.
When inactive, using the indicators will not trigger the blind spot view and
the camera will remain in Driving/Rear-View mode.
Note: this function will only work if the CAN-Bus wiring is connected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>