heatit HEAE4512680-692 Z-Push Wall Controller User Guide

heatit HEAE4512680-692 Z-Push Wall Controller

INTRODUCTION

The Heatit Z-Push Wall Controller is a wireless wall mounted Z-Wave Controller. It has mounting options for 1, 2 or 3 rockers, allowing for easy and practical management of your Z-Wave products. The switch can be set up to control scenarios or work in association with other Z-Wave products. Each rocker switch has a dual color LED to indicate button actions. The Heatit Z-Push Wall Controller is supplied with all three sets of rockers in the box. The switch fits into System 55 frames.

STATEMENT REGARDING PRODUCTS FROM MULTIPLE MANUFACTURERS

Please read this before installation

This device may be used with all devices certified with the Z-Wave PlusTM certificate and should be compatible with such devices produced by any manufacturer. Every primary controller is different depending on the manufacturer, their target audience and intended use/application. Please review the functionalities implemented by the primary controller you intend to use with our Z-Wave Plus certified device to ensure that it provides the necessary controls to take full advantage of our product’s capabilities.

INSTALLATION

Installation must be done by a qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation of the device, power to the device must be disconnected AT ALL TIMES!

1. Choose and mount the front, which covers your needs (for more information, see chapter “Choosing the correct front/assembly” described in the complete manual).
2. Gently pull the battery plastic tag to power the product.
3. Start the adding procedure from your primary controller.
4. Press any UP button 6 times in a rapid sequence on the device (the device has a label on the battery cover, pointing towards the UP buttons). Your device is now added in your primary controller.
5. Install the device in your preferred location.
   a. Fix the metal mounting bracket on the wall box or directly on the wall using the supplied screw kit.
   b. Place the device in the wall frame with arrows shown on label pointing upwards.
   c. Press the device and wall frame onto the metal mounting bracket.

Note: The rocker fastening clips may become looser after having been mounted and unmounted many times.

ADD/REMOVE

There are two ways to add your devices in a Z-Wave network:

Method 1: Standard (manual)

Please refer to your primary controller manual on how to set the primary controller in add/remove mode. The device can only be added or removed from the network if the primary controller is in add/remove mode.

1. Initiate the learning mode in the controller.
2. Press any UP button 6 times within 3 seconds.

When the learning mode has started, the LED corresponding to the button you pressed will blink green. The device will indicate “Success” by emitting a green light for 3 seconds.

Error while adding:
The learning mode times out after 30 seconds if the Heatit Z-Push Wall Controller does not receive any information from the gateway. The device will indicate “Fail” by emitting a red light for 3 seconds, if this happens, please perform a removing process from the controller before restarting learning mode.

Method 2: SmartStart (Automatic)

Please refer to your primary controller/gateway to see if SmartStart is supported by the controller. SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR-Code found on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

If the device already belongs to a network, follow the removing process before adding it to your network. Otherwise, the adding of this device will fail. When the device is removed from the network, the device will revert to factory settings.

TECHNICAL DATA

pushes per day)
Buttons| 1, 2 or 3 rockers
Ambient temperature| 5°C to 40°C (0°C to 40°C storage)
Humidity| Max 95% RH
Range RF| Min. 40 meters
IP Code| IP 20
Size (LxWxH)| 55 x 55 x 14mm
Approvals| Z-Wave Plus V2 CE RoHS 2002/95/EC 2002/96/EC (WEEE) 1999/5/EC (RTTE)

Heatit Controls AB can not be held liable for typographical errors, other errors or omittances in our information. Product specifications may change without further notice. All electrical installations must be carried out by a licensed electrician. The product must be installed in accordance with national building codes and our installers manual.

Heatit Controls AB l Läkarvägen 4, 454 31 BRASTAD, SWEDEN
Phone: +47 61 18 77 77 lpost@heatit.com – www.heatit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>