heatit 5430589 Smart Termostat User Guide
- June 3, 2024
- HEATIT
Table of Contents
heatit 5430589 Smart Thermostat
INTRODUCTION
Heat WiFi thermostat is an electronic thermostat for electrical underfloor heating. The thermostat has a simple user interface and can be easily programmed via the capacitive buttons. The color screen displays an accessible user interface. The thermostat has a built-in WiFi chip that allows you to control it from a user-friendly app. The ”Heatit WiFi” app is available on Google Play and in the App Store. Works with Amazon Alexa and Google Home (pending). If you are installing multiple thermostats in the same house, you may copy the settings from one thermostat to the next. This simplifies installation. Heat WiFi thermostat 16A is equipped with a single-pole switch and fits into most common frames (e.g. System 55, Elko RS16, Schneider Exxact). The thermostat can withstand a load of max 16A/3600W at 230VAC. We recommend a contractor for loads above 13A. The thermostat may be connected to an external sensor.
INSTALLATION
Installation must be done by a qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation of the device, power to the device must be disconnected AT ALL TIMES!
Release the front cover by pressing a screwdriver (e.g) into the ejector latch
centered at the bottom of the thermostat front. Be careful not to damage the
thermostat.
Connect the wires to the thermostat terminals:
- L Power connection (Live) 230VAC
- LOAD (N) Heating Cable connection (Neutral)
- LOAD (L) Heating Cable connection (Live)
- N Power connection (Neutral) 230VAC
- PILOT Pilot Wire (if applicable) 230VAC
- SENSOR Floor temp sensor, NTC type
Next, position the thermostat and fasten it onto the wall mounting box using 2-4 screws. Open the frame holder spring, position the frame and reattach the spring. Then attach the front, making sure the connectors between the front and back are correctly placed. Press the front carefully until it snaps into place.
STARTUP
After connecting the power to the thermostat for the first time or after
performing a factory reset, the startup wizard will prompt the following
questions:
- Language Set language
- Set timezone Timezone compared to GMT
- Daylight saving Daylight saving in use Y/N
- Date & time Set current date & time
- Thermostat use Heating or Cooling
- Heating system Floor (Slow), Floor (Fast), Other (Fast)
- Floor type Concrete or wooden
- Floor temp limit 5°C – 40°C (concrete) or 5°C – 27°C (wood)
- Choice of sensor Room/Floor
- Gradual Heating ON or OFF – used with new concrete floors to limit temperature rise time. Only in floor sensor mode.
WIFI CONNECTIONS
Start the ”Connect to cloud” process from the WiFi settings menu. Launch ”Add
thermostat” in the app on your phone. The thermostat will show two 3-digit PIN
codes. Enter these into your phone application. Next, enter your WiFi password
in your app. When the ”Add thermostat” process is finished, the thermostat
will reboot. Subsequently, you will be able to control your thermostat WiFi
settings through the app on your phone. For further information on installing,
setting up and using your Heatit WiFi thermostat, see the complete manual on
manuals.heatit.com.To transfer the installation to the customer, go to
Profile> View profile>Change email address. Customer cannot have registered a
user already. Customer logs in with own email and password set during account
creation.
TECHNICAL DATA
- Protocol WiFi 2.4GHz 802,11bgn
- Display 1.8” TFT, 128×160 resolution
- Rated voltage 230VAC 50Hz
- Max load 3600W (resistive loads only) Recommends contactor for loads higher than 13A
- Max current 16A
- Power consumption <2W
- Ambient temperature 2°C to 30°C
- Temperature range 5°C to 40°C
- Hysteresis 0.2°C to 2°C (0.5°C standard)
- Compatible with NTC
- sensors with value 6.8, 10, 12, 15, 22, 33, 47, 100 kΩ @ 25°C
- IP Code IP 21
- Approvals CE
Approved for use in bathrooms.
PHONE APPLICATIONS
Heatit Controls AB can not be held liable for typographical errors, other errors or omittances in our information. Product specifications may change without further notice. All electrical installations must be carried out by a licensed electrician. The product must be installed in accordance with national building codes and our installers manual.
Heatit Controls AB l Läkarvägen 4, 454 31 BRASTAD, SWEDEN
Phone: +47 61 18 77 77 l post@heatit.com –
www.heatit.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>