JBC HRR-A Articulated Right Hand Rest Instruction Manual
- June 13, 2024
- JBC
Table of Contents
www.jbctools.com
INSTRUCTION MANUAL
HRR
Articulated Right Hand Rest
This manual corresponds to the following reference:
HRR-A
Packing List
The following items are included:
| |
---|---|---
Articulated Right
Hand Rest Arm ……………… 1 unit| Height Adj. Flange …… 1 unit
Ref. 0023991| Manual ………………………. 1 unit
Ref. 0028803
Features
Assembly
Setting up the Articulated Hand Rest
Fit the shaft into the flange bushing (1) and tighten the headless screw at
the rear (2). Then assemble first the height adjustment flange (3) and finally
the hand rest arm (4) onto the shaft.
The articulated hand rest position should be like shown in the image. The
right hand rest is marked at its bottom side with the letter “R”.
Height Adjustment
According to your work needs, the articulated hand rest allows adjustment for
different heights through the vertical axis.
Slide the arm to the appropriate height (1) and secure it by tightening the
knob (2) to guarantee stability.
Work Position Adjustment
HRR Articulated Right Hand Rest allows adjustment for different positions according to your work needs.
The articulated arm covers the entire working area.
The correct hand work position is shown in the following images:
Accessories*
If a second hand rest ist needed, Articulated Left Hand Rest HRL is available. HRL also allows adjustment for different positions.
In the case of using both left and right arms, assemble both
as shown in the illustration according to the letters on the back of the hand
rest, to keep the hand supports at the same level. The right hand rest should
be assembled below the left hand rest.
Compatible JBC Articles*
HRR and HRL can be combined with:
RWT Adjustable Rework Arm,
RWS Adjustable Rework Arm for PHSE and
RWB Adjustable Rework Arm for PHBE.
Assemble first the height adjustment flange (1), then the HRR (2) and
afterward the HRL (3). Assemble the second height adjustment flange (4) and
finally the RWT (5).
4 different sizes for PCB Supports are available:
– PHNS Support for PCBs up to 11×7 cm / 4×3”
– PHSS Support for PCBs up to 13×13 cm / 5×5”
– PHBS Support for PCBs up to 36×28 cm / 14×11”
– PHXLS Support for PCBs up to 51×61 cm / 20×24”
Maintenance
- Check periodically that the HRR is clean, especially the sliding parts and the shaft.
- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.
- Replace any defective damaged parts. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service
Do not leave the HRR over the preheater when it is in operation.
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions.
-
Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause a fire.
-
The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
-
Be careful with the fumes produced when soldering.
-
Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
-
Do not leave up the arms directly above heat surfaces.
-
Utmost care must be taken with liquid tin waste which can cause burns.
-
This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved.
Children must not play with the appliance. -
Maintenance must not be carried out by children unless supervised.
Specifications
HRR
Articulated Right Hand Rest
Ref. HRR-A
– Arm Length: 444,5 mm / 17.5 in
– Total Net Weight: 1060 g / 2.34 lb
– Package Dimension / Weight: 280 x 280 x 164 mm / 2.18 g
(L x W x H) 11.02 x 11.02 x 6.46 in / 4.80 lb
Complies with CE standards
ESD Safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/ within 30 days of
purchase.
**** This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility.
www.jbctools.com
0028803-181122
Documents / Resources
| JBC
HRR-A Articulated Right Hand
Rest
[pdf] Instruction Manual
HRR-A Articulated Right Hand Rest, HRR-A, Articulated Right Hand Rest, Right
Hand Rest, Hand Rest
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>