heatit Z-Push Wall Controller User Guide
- June 4, 2024
- HEATIT
Table of Contents
heat it Z-Push Wall Controller
INTRODUCTION
The Heat Z-Push Wall Controller is a wireless wall-mounted Z-Wave Controller. It has mounting options for 1, 2 or 3 rockers, allowing for easy and practical management of your Z-Wave products. The switch can be set up to control scenarios or work in association with other Z-Wave products. Each rocker switch has a dual-color LED to indicate button actions. The Heat Z-Push Wall Controller is supplied with all three sets of rockers in the box. The switch fits into System 55 frames.
STATEMENT REGARDING PRODUCTS FROM MULTIPLE MANUFACTURERS
Please read this before installation
This device may be used with all devices certified with the Z-Wave Plus™
certificate and should be compatible with such devices produced by any
manufacturer. Every primary controller is different depending on the
manufacturer, their target audience, and intended use/application. Please
review the functionalities implemented by the primary controller you intend to
use with our Z-Wave Plus certified device to ensure that it provides the
necessary controls to take full advantage of our product’s capabilities.
INSTALLATION
Installation must be done by a qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation of the device, power to the device must be disconnected AT ALL TIMES!
- Choose and mount the front, which covers your needs (for more information, see chapter ”Choosing the correct front/assembly” described in the complete manual).
- Gently pull the battery plastic tag to power the product.
- Start the adding procedure from your primary controller.
- Press any UP button 6 times in a rapid sequence on the device (the device has a label on the battery cover, pointing toward the UP buttons). Your device is now added in your primary controller.
- Install the device in your preferred location.
- Fix the metal mounting bracket on the wall box or directly on the wall using the supplied screw kit.
- Place the device in the wall frame with arrows shown on the label pointing upwards.
- Press the device and wall frame onto the metal mounting bracket.
Note: The rocker fastening clips may become looser after having been
mounted and unmounted many times.
ADD/REMOVE
There are two ways to add your devices to a Z-Wave network:
Method 1: Standard (manual)
Please refer to your primary controller manual on how to set the primary
controller in add/remove mode. The device can only be added or removed from
the network if the primary controller is in add/remove
mode.
- Initiate the learning mode in the controller.
- Press any UP button 6 times within 3 seconds.
When the learning mode has started, the LED corresponding to the button you
pressed will blink green. The device will indicate ”Success” by emitting a
green light for 3 seconds. Error while adding The learning mode times out
after 30 seconds if the Heat Z-Push Wall Controller does not receive any
information from the gateway. The device will indicate ”Fail” by emitting a
red light for 3 seconds, if this happens, please perform a removal process
from the controller before restarting learning mode.
Method 2: SmartStart (Automatic)
Please refer to your primary controller/gateway to see if SmartStart is
supported by the controller. SmartStart-enabled products can be added to a
Z-Wave network by scanning the Z-Wave QR-Code found on the product with a
controller providing SmartStart inclusion. No further action is required and
the SmartStart product will be added automatically within 10 minutes of being
switched on in the network vicinity. If the device already belongs to a
network, follow the removing process before adding it to your network.
Otherwise, the addition of this device will fail. When the device is removed
from the network, the device will revert to factory settings.
TECHNICAL DATA
- Protocol: Z-Wave Plus, 868.4MHz
- Chip: Z-Wave 700 chip
- Battery: 1 x CR2450 battery
- Est. battery life: Estimated 1 year (with default setting and max. 10 pushes per day)
- Buttons: 1, 2, or 3 rockers
- Ambient temperature: 5°C to 40°C (0°C to 40°C storage)
- Humidity: Max 95% RH
- Range RF: Min. 40 meters
- IP Code: IP 20
- Size (LxWxH): 55 x 55 x 14mm
- Approvals: Z-Wave Plus V2
CE
RoHS 2002/95/EC
2002/96/EC (WEEE)
1999/5/EC (RTTE)
Heat Controls AB can not be held liable for typographical errors, other errors, or omittances in our information. Product specifications may change without further notice. All electrical installations must be carried out by a licensed electrician. The product must be installed in accordance with national building codes and our installers manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>