kogan KDCMPTNT4PA 1 Bedroom Familt Camping Tent User Manual
- June 6, 2024
- Kogan
Table of Contents
USER GUIDE
K0M0DO
BEDROOM FAMILY CAMPING TENT
4 PERSONS
KDCMPTNT4PA
SAFETY & WARNINGS
Ensure to read all instructions and warnings in this user guide prior to first use.
- This tent is designed to be a temporary structure. Do not use this tent as a permanent dwelling.
- Keep the tent away from all flames heat sources to avoid potential damage.
- Do not store flammable liquids inside the tent.
- Do not spray the tent with insecticides. They can be flammable and may damage the tent’s material.
- Ensure the area the tent is set up is clear of sharp objects and obstructions to avoid damage to the material.
- Do not pitch the tent under trees due to the potential of lightning strikes and falling tree branches.
- Do not pitch the tent near a cliff.
- Do not leave the tent pitched in the face of strong winds. Disassemble the tent before seeking refuge.
- Ensure all guy ropes and pegs are fully secured before using the tent.
- Do not cook inside the tent.
- Do not smoke inside the tent.
- If wet, always allow the tent to dry before storing in the carry bag to prevent the growth of mildew.
COMPONENTS LIST
- Tent body (x1)
- Inner tent (x1)
- Tent floor (x1)
- 5.3m fiberglass pole (x2)
- 4.8m fiberglass pole (x1)
- Peg (x23)
- 3m guy rope (x6)
- 2.2m guy rope (x6)
- Carry bag (x1)
ASSEMBLY
Step 1: Ensure you are in a flat open area with sufficient space to set up the
tent. Take out all components from the carry bag and lay the tent body out on
the ground.
Step 2: Secure the tent
body to the ground by inserting pegs through each loop on the tent body.
Inserting the pegs at a 45° angle will ensure the tent body stays grounded.
Step 3: Unfold and connect the joints of one fiberglass pole. Repeat this
process with the two remaining poles.
Step 4: Insert one 5.3m
fibreglass pole through one of the sleeves located over the width and at the
back of the tent body.
Repeat this process with the other 5.3m fibreglass pole using the sleeve in
the middle of the tent body.
Repeat the process again with the 4.8m fibreglass pole using the sleeve
closest to the entrance of the tent.
Step 5: Secure the ends of
each fibreglass pole with the pins located at the base of the tent body.
Attach the clips located on the tent body to the fibreglass poles.
Step 6: Moving inside the tent body, unfold the inner tent, and connect the
hooks of the inner tent onto the loops on the ceiling of the tent body.
Step 7: Unfold the tent floor and attach the hooks on the tent floor to the
rings on the base of the tent body. 
Step 8: Moving back outside, thread the guy ropes through the loops located
near the poles then secure them with the pegs. Tent assembly is now complete.
DISASSEMBLY
Step 1: Remove all pegs and guy ropes
Step
2: Detach the tent floor from the tent body.
Step 3: Disconnect the inner tent from the ceiling of the
tent body. Fold the inner tent. 
Step 4:
Detach the clips on the tent body from the poles.
Step 5: Detach each pole end from the pins located at the base of the tent body.
Step 6: Remove each pole
from the pockets. 
Step 7: Fold the poles back
to their original state.
Step 8: Place all components back into the carry bag.
DIMENSIONS
Outer dimensions
| Rear panel (A): | 118.5cm | Front panel (E): | Front panel (E): |
|---|---|---|---|
| Side back (B): | 114.5cm | Height (F): | Height (F): |
| Side front (C): | 129cm | Front entrance (G): | Front entrance (G): |
| Side combined (D): | 243.5cm |
Inner dimensions
| Height: | 188cm |
|---|---|
| Width: | 243cm |
| Depth: | 216cm |
Need more information?
We hope that this user guide has given you the assistance needed for a simple
setup.
For the most up-to-date guide for your product, as well as any additional
assistance you may require, head online to
help.kogan.com
kogan.com