unicorecomm UC6226NIS GNSS Positioning Chip Evaluation Kit User Guide

June 12, 2024
unicorecomm

unicorecomm UC6226NIS GNSS Positioning Chip Evaluation Kit

Copyright© 2009-2023, Unicore Communications, Inc. Data subject to change without notice.

Revision History

Version Revision History Date
R1.0 First release Apr. 2023

Legal right notice
This manual provides information and details on the products of Unicore Communication, Inc. (“Unicore”) referred to herein. All rights, titles and interests to this document and the information such as data, designs, and layouts contained in this manual are fully reserved, including but not limited to the copyrights, patents, trademarks and other proprietary rights as relevant governing laws may grant, and such rights may evolve and be approved, registered or granted from the whole information aforesaid or any part(s) of it or any combination of those parts. Unicore holds the trademarks of “和芯星通”, “UNICORECOMM” and other trade names, trademarks, icons, logos, brand names, and/or service mark of Unicore products or their product serial referred to in this manual (collectively “Unicore Trademarks”). This manual or any part of it, shall not be deemed as, either expressly, implied, by estoppel or any other form, the granting or transferring of Unicore rights and/or interests (including but not limited to the aforementioned trademark rights), in whole or in part.

Disclaimer
The information contained in this manual is provided “as is” and is believed to be true and correct at the time of its publication or revision. This manual does not represent, and in any case, shall not be construed as a commitment or warranty on the part of Unicore with respect to the fitness for a particular purpose/use, the accuracy, reliability, and correctness of the information contained herein. Information, such as product specifications, descriptions, features and user guide in this manual, are subject to change by Unicore at any time without prior notice, which may not be completely consistent with such information of the specific product you purchase. Should you purchase our product and encounter any inconsistency, please contact us or our local authorized distributor for the most up-to-date version of this manual along with any addenda or corrigenda.

Foreword

This document provides information of Unicore’s UC6226NIS evaluation kit (EVK). It can be used together with UPrecise_User Manual.

Target Readers
This manual is written for technicians who are familiar with GNSS chips. It is not for general readers.

Overview

UC6226NIS evaluation kit (hereinafter referred to as EVK) is mainly used to test and evaluate the function and performance of the UC6226NIS chip for user convenience. The delivered package contains:

Table 1-1 UC6226NIS EVK Package

Type Contents Number
Main device UC6226NIS EVK Suite 1
Accessory Alligator clip test leads 2
Accessory 12V power adapter 1
Accessory GNSS antenna – OSAnm10854G 1
Accessory Straight through serial cable 1
Accessory Micro-B USB cable 1

EVK Introduction

The figure below shows the appearance of the UC6226NIS EVK Suite.

Interfaces & Indicator

unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-
fig-2

Figure 3-1 Interfaces & Indicator on UC6226NIS EVK (Front Panel)

unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-
fig-3

Figure 3-2 Interfaces & Indicator on UC6226NIS EVK (Rear Panel)

Table 3-1 Interfaces & Indicator on UC6226NIS EVK

No.

| Interface/ Indicator|

Description

---|---|---
1| DC/12V| +12V power adapter interface

2

|

USB

| Power supply and data interface: use a mobile phone communication cable to connect the EVK and a computer for power supply of + 5V and data transmission

No.

| Interface/ Indicator|

Description

---|---|---

3

|

VSEL

| Power and communication selection interface: as shown in Figure 3-3, when the jumper connects pin 2 and pin 4, the power supply is

12 V, and the communication interface is DB9-232; when the jumper connects pin 4 and pin 6, the power supply is 5 V, and you can use the USB cable for both power supply and data transmission.

4

|

Indicator

| Power / PPS indicator, which flashes when the positioning state is effective.
5| ANT| RF signal input: this interface is connected to the antenna
6| CLK| Backup

7

|

CFG

| VCC_IO interface: control the UC6226NIS IO power on and off using the jumper
VCC_CORE interface: control the UC6226NIS core power on and off using the jumper; it can be used to test the chip power consumption
V_BACK interface: control V_BACK power on and off using the jumper (recommended not to move)
8| UART| Backup

unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-
fig-4

(Left: +12V power supply using the adapter; right: +5V power supply using the USB cable)

Installation & Function Test

Installation

  • Step 1: Make sure to take full anti-static measures, such as wearing anti-static wrist straps and grounding the workbench.
  • Step 2: Select the GNSS antenna with appropriate gain (the GNSS systems and frequencies supported by the antenna should be in line with the chip), fix it in the nonblocking area, and connect the antenna to the ANT port on the EVK.
  • Step 3: Connect the EVK to the PC. There are two ways to supply power and transfer data:
  1. If you use the USB cable, you should install the jumper on the top right-hand corner at the VSEL interface (see Figure 3-3), and connect the EVK to the PC for power supply and data transmission.
  2. If you use the 12 V power adapter, you should install the jumper on the top left-hand corner at the VSEL interface (see Figure 3-3), and use the straight through serial cable to transfer data.
  3. Step 4: Open the UPrecise software on the PC.
  4. Step 5: Configure the receiver through UPrecise to display the constellation view, data stream, tracking status, etc. For more information, please refer to UPrecise_User Manual.unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-fig-6

Power Consumption Test
Taking the power consumption of VCC_CORE as an example, when the EVK is powered off, remove the jumper on the VCC_CORE interface (as shown in Figure 3-4), and use two alligator clip test leads; connect one end of the leads to the tested pins and the other end to a multimeter. Adjust the multimeter to the current mode, and set the gear to “A”. Power on the EVK, and check the test current of the ammeter after normal positioning, and the value of 3.3V * test value is the chip’s core power consumption. Use similar method to test the power consumption of VCC_IO and V_BACK respectively.

unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-
fig-7

Notes
When using the USB cable for power supply and communication, there may be a serial port mouse conflict. At this time, the serial enumerator needs to be removed from the serial port settings, as shown below:

unicorecomm-UC6226NIS-GNSS-Positioning-Chip-Evaluation-Kit-
fig-8unicorecomm-UC6226NIS-GNSS-
Positioning-Chip-Evaluation-Kit-fig-9

Unicore Communications, Inc.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

unicorecomm User Manuals

Related Manuals