BANNER WLS15 Pro LED Strip Light with PICK-IQ Instruction Manual

June 6, 2024
BANNER

BANNER  LOGO.JPG

BANNER WLS15 Pro LED Strip Light with PICK-IQ Instruction Manual

BANNER WLS15 Pro LED Strip Light with PICK-IQ.png

Banner’s WLS15 Pro LED Strip Lights with PICK-IQ™ have sturdy aluminum inner frames, encased in shatter resistant, UV-stabilized, polycarbonate shells, making them ideal for indoor and outdoor applications.

FIG 1 Banner's WLS15 Pro LED Strip Lights.JPG

  • Bright, programmable strip light with RGB LEDs
  • 19 color options for varied indication and inspection uses
  • PICK-IQ gives full access to individual LED control, color, flashing, intensity, and animation settings, as well as advanced level, gauge, and segment operating modes
  • Available in six lengths from 220 mm to 1200 mm
  • Low-profile, space-saving design
  • Rugged, water-resistant design

Important: Read the following instructions before operating the light. Please download the complete WLS15 Pro LED Strip Light with PICK-IQ technical documentation, available in multiple languages, from www.bannerengineering.com for details on the proper use, applications, Warnings, and installation instructions of this device.

Models

FIG 2 Models.JPG

Communication

PICK-IQ™ is a purpose-built, Modbus RTU compatible, serial bus protocol that uses a common ID to reduce the typical latency that results from polling multiple devices. The WLS15 Pro with PICK-IQ does not have a common ID, however it is compatible with and can be used alongside other PICK-IQ devices. It can also be used as a standalone device controlled with Modbus RTU serial bus protocol. A Modbus master controller is required to make changes to the device.

For more information about the WLS15 Pro with PICK-IQ device registers, refer to document PN 219137.

For more information about PICK-IQ devices and the common ID, refer to document PN 206185.

Wiring Diagrams

FIG 3 Wiring Diagrams.JPG

PICK-IQ (Modbus RTU Serial Bus Protocol) Configuration for the WLS15 Pro

For more information about the WLS15 Pro with PICK-IQ device registers, refer to document PN 219137. Segment Mode Configure the light to have up to 10 segments which scale in size automatically with the length of the light or select Manual Segment Configuration which allows each segment to have a custom LED width and LED offset from the beginning of each segment to the beginning of the light.

Use device registers to set each segment to off, solid on, flash, or animation mode and change segment number and configuration, color, intensity, flash speed, direction, background, threshold markers, and select animation type.

FIG 4 Animation Description.JPG

FIG 5 Animation Description.JPG

Run Mode

Use device registers to control the entire light and select color, intensity, flash, direction, and animations. Create custom colors, intensity, and flash speeds.

FIG 6 Run Mode.JPG

FIG 7 Run Mode.JPG

Level Mode

Use device registers to set the level value and to set range, thresholds, colors, intensities, flash speeds, background, threshold markers, and animation types.

FIG 8 Level Mode.JPG

FIG 9 Level Mode.JPG

Dim and Blend Mode

Dim and blend mode uses the light to finely adjust the intensity of one color, or blend between two or three colors. Use device registers to set the dim and blend mode value and to set number of colors, range, colors, and intensities.

FIG 10 Dim and Blend Mode.JPG

FIG 11 Dim and Blend Mode.JPG

Gauge Mode

Gauge mode uses the light to display a colored band of LEDs in a position proportional to the gauge mode value. Use device registers to set the gauge mode value and to set range, thresholds, colors, intensities, flash speeds, background, threshold markers, and animation types.

FIG 12 Gauge Mode.JPG

FIG 13 Gauge Mode.JPG

LED Mode

Use device registers to turn on and select a color for each individual LED. Use additional device registers to set global intensity.

FIG 14 LED Mode.JPG

Demo Mode
Demo sequence cycles through 12 different configurations to highlight example applications.

Specifications

Supply Voltage
12 V DC to 30 V DC
Use only with suitable Class 2 power supply (UL) or a SELV power supply (CE) See electrical characteristics on product label

FIG 15 Supply Voltage.JPG

Supply Protection Circuitry
Protected against reverse polarity and transient voltages

Note: Do not spray cable with high-pressure sprayer, or cable damage will result.

Construction
Clear anodized aluminum housing
Polycarbonate outer housing
Polyamide end caps

Connections
150 mm (6 in) PVC cable with a 4-pin M12 male quick disconnect
Models with a quick disconnect require a mating cordset

Input Response Time
45 ms maximum

Mounting
Integral mounting slots for M4 (#8) screws, tighten to 0.56 N·m (5 in·lbf) max torque
Multiple bracket options available
Secure cables within 150 mm (5.9 in) of the light

Note: It is recommended to use the provided mounting bushings when mounting using the endcaps. Center the mounting bushings in each slot to allow for expansion and contraction. Install using a M4 (#8) screw in each bushing torqued to a maximum of 0.45 N-m (4 in-lbf). For 920 mm and 1200 mm models in environments that vary more than 10 °C (18 °F), it is recommended to use one of the mounting bracket options instead of the end cap slots. If using the LMBWLS15 clip bracket and additional attachment is desired, only one end may be fastened using one of the spacers provided in the LMBWLS15 hardware packet to allow the opposite end to expand and contract. See mounting options in the instruction manual for bracket and tape options that allow expansion and contraction over temperature variations.

Environmental Rating
Rated IEC IP66 and IEC IP67
Suitable for wet locations per UL 2108

Vibration and Mechanical Shock
Vibration: 10 Hz to 55 Hz, 1.0 mm peak-to-peak amplitude per IEC 60068-2-6
Shock: 15G 11 ms duration, half sine wave per IEC 60068-2-27

Operating Temperature
–40 °C to +50 °C (–40 °F to +122 °F)
Storage Temperature: –40 °C to +70 °C (–40 °F to +158 °F)

Certifications

FIG 16 Certifications.JPG

Light Characteristics

RGB LED PWM Frequency: 1kHz

FIG 17 Light Characteristics.JPG

Dimensions

FIG 18 Dimensions.JPG

Accessories

Cord sets
Use single-ended cord sets between the power source and the quick disconnect connection of the first device in a chain. Use double ended cord sets between devices in a chain.

PSD-24-4

  • 90 to 264 V AC 50/60 Hz input
  • Includes a 1.8 m (6 ft) US style 5-15P input plug
  • 24 V DC UL Listed Class 2 M12 connector output
  • 4 A total current

FIG 19 PSD-24-4.jpg

PSW-24-1

  • 24 V DC, 1 A Class 2 UL Listed power supply
  • 100 V AC to 240 V AC 50/60 Hz input
  • 2 m (6.5 ft) PVC cable with M12 quick disconnect
  • Includes Type A (US, Canada, Japan, Puerto Rico, Taiwan), Type C (Germany, France, South Korea, Netherlands, Poland, Spain, Turkey), Type G (United Kingdom, Ireland, Singapore, Vietnam), and Type I (China, Australia, New Zealand) AC detachable input plugs

FIG 20 PSW-24-1.jpg

FIG 21 4 Pin Threaded M12 Cordsets.JPG

FIG 22 4 Pin Threaded M12 Cordsets.JPG

FIG 23 5 Pin M12 Shielded Twisted Pair Cordsets.JPG

FIG 24 5 Pin Threaded M12 Shielded Twisted Pair
Cordsets.JPG

Mounting Accessories

LMBWLS15

  • Stainless steel clip bracket
  • Includes 3 clip brackets and 2 plastic spacers
  • Clearance hole for M5 hardware

FIG 25 LMBWLS15.JPG

LMBWLS15-150S

  • Set of 2 stainless steel swivel bracket, allows for 150° of movement
  • Clearance hole for M5 button head screw

FIG 26 LMBWLS15-150S.JPG

LMBWLS15MAG

  • Set of 2 brackets
  • Magnetic mounting bracket for attachment to steel and iron surfaces

FIG 27 LMBWLS15MAG.JPG

LMBWLS15TD

  • Includes 4 100 mm (4 in) strips of 3M™ Dual Lock™ reclosable fasteners
  • Recommended for mounting to metal and plastic surfaces
  • Strong, pressure-sensitive adhesive bonds on contact

FIG 28 LMBWLS15TD.JPG

LMBWLS15TF

  • Includes 2 100 mm (4 in) strips of double-sided foam urethane strips
  • Acrylic adhesive provides high bond strength to most surfaces
  • Bonds to low surface energy plastics such as polypropylene and powder coated paints

FIG 29 LMBWLS15TF.JPG

All measurements are listed in millimeters [inches], unless noted otherwise.

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not
cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the
product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time.
Specifications and product information in English supersede that which is provided in any other language.

For the most recent version of any documentation, refer to:
www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents

FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)

This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the manufacturer.

Mexican Importer

Banner Engineering de Mèxico, S. de R.L. de C.V.
David Alfaro Siqueiros 103 Piso 2 Valle oriente
San Pedro Garza Garcia Nuevo Leòn, C. P. 66269
81 8363.2714

BANNER  LOGO.JPG

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals