Bestway 65052 Hydro Force Ventura Elite X2 Inflatable Kayak Set Installation Guide
- June 16, 2024
- Bestway
Table of Contents
Bestway 65052 Hydro-Force Ventura Elite X2 Inflatable Kayak Set
Product Information
Technical Specifications
- Item 65118
- Recommended working pressure: 0.07 bar (1 psi)
- Maximum load capacity: 130 kg (286 lbs)
- Maximum number of persons: 1 adult
- Item 65052
- Recommended working pressure: 0.07 bar (1 psi)
- Maximum load capacity: 200 kg (440 lbs)
- Maximum number of persons: 2 adults
Inflate & Assemble
Item 65118
- Product Inflated Size: 2.80m x 86cm (9’2 x 34″)
- Deflated Size: 5 cm / 10 cm
- Printed Scale Inflated Size: 5.1 cm / 10.3 cm
Item 65052
- Product Inflated Size: 3.30m x 86cm (10’10 x 34″)
- Deflated Size: 5 cm / 10 cm
- Printed Scale Inflated Size: 5.1 cm / 10.3 cm
Safety Rope Installation
Owner’s Manual
Please keep this manual in a secure place and hand it over to the new owner when you sell the craft.
FAQ
1. What is the recommended working pressure for item 65118?
The recommended working pressure for item 65118 is 0.07 bar (1 psi).
2. What is the maximum load capacity for item 65052?
The maximum load capacity for item 65052 is 200 kg (440 lbs).
3. How many adults can item 65118 accommodate?
Item 65118 can accommodate 1 adult.
4. What are the dimensions of the inflated size for item 65052?
The dimensions of the inflated size for item 65052 are 3.30m x 86cm (10’10 x 34″).
Dimension
Installation Instruction
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Follow all the Safety and Operating Instructions. If you don’t follow these instructions, it may cause overturn, explode the boat and causes to drowning
- Before every use, carefully inspect all boat components including air chambers, grab ropes, oars, and air valves, to ensure everything is in good condition and tightly secured. Please stop to repair if you find any damage.
- Passenger numbers and load weights shall by no means exceed specified capacities. Refer to the Technical Specifications section of this manual to determine passenger numbers and load weights for your boat. Overweight will cause overturn and drowning.
- Inflate according the numbered air chamber and rated pressure on the boat, or it will cause overinflation and boat explosion. Exceeding the data given on the capacity plate may cause the craft to damage, overturn and lead to drowning.
- Keep the boat balanced. Uneven distribution of persons or load in the boat may cause overturn the boat and drowning.
- BE AWARE OF OFFSHORE WINDS AND CURRENTS.
- Don’t leave the boat exposed to sun for long periods of time, as high temperatures can increase air expansion, which can cause irreparable damage.
- Never transport the boat in inflated condition on the car. Be aware of the potential harmful effects of liquids such as battery acid, oil, petrol. The liquids may damage your boat.
TECHNICAL SAFETY INSTRUCTIONS
- Follow these instructions to avoid drowning, paralysis or other serious injuries.
- Do not exceed the maximum recommended number of people. Regardless of the number of people on board, the total weight of people and equipment must never exceed the maximum recommended load. Always use the seats/seating spaces provided.
- When loading the craft, never exceed the maximum recommended load. Carefully distribute the weight appropriately to ensure the craft remains level. Avoid placing heavy items in the front.
- The maximum recommended load includes the weight of all people on board, all provisions and personal effects, any equipment not attached to the craft, cargo (if any) and all consumable liquids (water, fuel, etc.).
- When using the boat, life-saving devices such as life jackets and buoys should be inspected beforehand and used at all times.
- Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.
- When the boat is in motion, all passengers must remain seated at all times to avoid falling overboard.
- Use the boat in protected shore zones, up to 300 m (984 ft.). Be aware of natural factors such as wind, tidewaters and tidal waves.
- Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may puncture the boat.
- If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber to prevent the boat from sinking.
- To avoid damage, do not drag the boat on rough surfaces.
- It is the responsibility of the owner/operator to have at least a bucket/bailer on board, secured against accidental loss.
- Be responsible, and do not neglect the safety rules as this could jeopardize your life and the lives of others.
- Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself about local regulations and dangers related to boating and/or other water activities.
- Drawings are for illustration purposes only. May not reflect actual product. Not to scale.
TECHNICAL SPECIFICATIONS
Item| Recommended working pressure| Maximum load capacity|
Maximum number of persons
---|---|---|---
65118| 0.07bar (1psi)| 130kg (286Ibs)| 1 adult
65052| 0.07bar (1psi)| 200kg (440Ibs)| 2 adults
INFLATE & ASSEMBLE
NEVER USE HIGH-PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR PRODUCT.
- Inflate only as far that after inflating one can see some folding at the welding seams. After inflation compare the height of the printed scale on the product with the following table to make sure the height of each chamber is reached. Inflate bottom chamber and other accessories such as footrest cushion until it is stiff to the touch but NOT hard. DO NOT OVER INFLATE.
- Take care that the boat has gotten to the correct pressure. Pay attention to both pressure scales on the type-plate and check the pressure from time to time, because in the sun the pressure can grow and it must be balanced then to the correct one.
- Extended exposure to sun can shorten the lifespan of your boat. We suggest to not leaving boats in direct sunlight for more than 1 hour after use.
Item
|
Product Inflated Size
| Printed Scale
---|---|---
Deflated Size| Inflated Size
65118| 2.80m x 86cm (9’2″ x 34″)| 5 cm / 10 cm| 5.1 cm / 10.3 cm
65052| 3.30m x 86cm (10’10” x 34″)| 5 cm / 10 cm| 5.1 cm / 10.3 cm
SAFETY ROPE INSTALLATION
- Safety ropes shall be fitted to both sides of the bow and stern areas only and shall not impede the normal operation of the craft.
- Do check carefully if the saving rope is tightened well.
SEATS AND STORAGE BAG ASSEMBLY
- After the craft is inflated, connect the belts of the seats to the side buckles on the craft, and make sure the storage bag is vertical.
- The location of the seats can be adjusted along with centre of the craft floor.
- Connect the storage bag to the D-buckle.
STORAGE
- Remove the oars from the oarlocks. Take down the storage bag and seats.
- Carefully clean the boat using a mild soap with clean water. Do not use acetone, acid, and/or alkaline solutions.
- Use a cloth to gently dry all surfaces. The product can be dry under direct sunlight for not more than 1 hour, extended exposure to sun can shorten the lifespan of the boat.
REPAIR
- If there is a small puncture, repair it according to the instructions on the repair patch.
- If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a specialty shop to make the repair.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU SELL THE CRAFT.
Manufactured, distributed and represented in the European Union by/ Bestway Europe S.p.a., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia Tel: Australia: +61 2 9037 1388; New Zealand: 0800 142 101 Distributed in the United Kingdom by Bestway Corp UK Ltd. 8 Wentworth Road, Heathfield Industrial Estate, Newton Abbot, Devon, TQ12 6TL Exported by/Exporté par/Exportado por/Exportiert von/Esportato da Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong ©2023 Bestway Inflatables & Material Corp.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>