GEBERIT 972.178.00.0 FlowFit Pressbacke User Manual

GEBERIT 972.178.00.0 FlowFit Pressback

Product Information

• Specifications:
  • Brand: Geberit
  • Model: FlowFit
  • Product Type: Pressbacken
  • Part Number: 972.178.00.0(00)
• Product Description:
  • The Geberit FlowFit Pressbacken is designed for pressing Geberit system pipes and press fittings. It features a back lever, press tip, tab with dimension indication, jaw joints, and flange.
• Usage Instructions:
  • Place the Geberit FlowFit Pressbacken on the press indicator of the Geberit press fitting.
  • Ensure that the press jaw is correctly positioned on the press indicator.
  • Release both ends of the back lever.
  • Press the Geberit press fitting.
  • Do not repress any incorrectly pressed connections to avoid leaks.
• Maintenance:
  • Follow the maintenance intervals and tasks described below for the Geberit Pressbacken:
  • Remove deposits on the press tips regularly.

FAQs

• Q: Can I use the Geberit pressing jaws with any pressing tool?
  • A: Geberit recommends using the pressing jaws only with specific pressing tools mentioned in the manual. Using other tools can reduce the service life of the pressing jaws.
• Q: What should I do if I encounter a leak due to incorrect pressing?
  • A: If there is a leak due to incorrect pressing, replace the connection. Do not attempt to repress it.

Basic safety notes

Intended use

• The Geberit pressing jaws are intended exclusively for pressing Geberit system pipes and press fittings.
• Geberit recommends using the Geberit pressing jaws in the following pressing tools only:
  • Viega Picco
  • Nussbaum Picco
  • Ridgid RP 210/241
• Other pressing tools have not been tested by
• Geberit in terms of their suitability for the Geberit pressing jaws. Using pressing tools with excessive pressing force can significantly reduce the service life of the pressing jaws.
• Only use the Geberit pressing jaws that correspond to the diameter of the Geberit press fittings to be processed.
• Geberit pressing jaws may only be used by skilled persons qualified in pipe installations.

Improper use

• The Geberit FlowFit pressing jaws are exclusively intended to be used by this user manual. Other uses are deemed to be improper and can lead to injury.

User qualifications

• Without suitable training, users cannot detect or may incorrectly estimate the hazards presented by the pressing procedure. They are therefore at risk of injuring themselves or others.
• Users must be conversant with and apply country-specific safety regulations.
• Users working with the Geberit pressing jaws for the first time must have been instructed by an expert in the safe handling of the pressing jaws or have attended a specialist course.

Following information and instructions

• Failure to observe the safety notes and instructions can lead to injuries.
• Read through and observe all safety notes and instructions relating to the Geberit pressing tool and pressing jaw before commissioning.
• Read and observe the safety notes for the consumables used.
• Retain all safety notes and instructions for future use.

Avoiding hazards caused by defective

• Geberit pressing jaws
  • Geberit pressing jaws are exposed to serious forces during the pressing procedure and wear out. The use of worn or damaged pressing jaws can lead to injuries.
  • Only use the pressing jaws if they are in perfect working order.
  • Maintain the pressing jaws regularly. → See maintenance regulations for Geberit pressing jaws.
  • Only store the pressing jaws in dry rooms.
  • Transport pressing jaws in shock-protected transport cases.
  • Regularly inspect pressing jaws for defects and damage before and after every use. Inspect the pressing jaws particularly for incipient cracks in the pressing contour and on the flanges.
  • If there are incipient cracks, take the pressing jaws out of service immediately, label them as defective and do not use them again.

Avoiding damage to the Geberit pressing jaws caused by faulty pressing operations

• Geberit pressing jaws can be damaged by faulty pressing operations or use, such as by being pressed by foreign bodies.
• Do not tilt the pressing jaws on the pressfitting.
• If you suspect that the pressing jaws are damaged (for example, if sharp edges appear on the pressfitting after the pressing procedure), they must be replaced.

Using personal protective equipment

• People can be injured without suitable protective equipment. Wear a protective helmet, protective goggles and safety shoes during the pressing procedure.

Explanation of symbols

Symbols in the instructions

Symbols on the product

Product Description

Structure of the Geberit FlowFit pressing jaws

1. Jaw lever
2. Pressing tip
3. Plate with dimension specifications
4. Jaw joints
5. Flange

Operation

Inserting the Geberit FlowFit pressing jaw into the pressing tool

CAUTION Risk of injury due to unsecured Geberit pressing attachments falling

• When inserting the Geberit pressing attachments (pressing jaws, adapter jaws) into the tool holder, the pressing tool must be upright.
• ATTENTION Damage to the device caused by incorrect use
• Only use pressing tools that are recommended for the intended use with the Geberit pressing attachments (pressing jaws, pressing collars, adapter jaws) by Geberit.
• Insert the Geberit pressing jaw into the pressing tool as instructed.
• See operating instructions for the relevant pressing tool.

Pressing with the Geberit FlowFit pressing jaw

1. To open the Geberit pressing jaw, push the ends of the jaw levers together. Position the open pressing jaw on the pressing indicator of the Geberit pressfitting.
2. Make sure that the Geberit pressing jaw is positioned correctly on the pressing indicator of the Geberit pressfitting.
3. Release both jaw lever ends.
   • CAUTION: Danger of crushing
   • Keep your hands at a safe distance from the Geberit pressing jaw.
   • ATTENTION: Damage to the Geberit pressing jaw due to a failed pressing sequence
   • The Geberit pressing jaw can be damaged as a result of a failed pressing sequence.
   • Replace the damaged pressing jaw and take it out of service.
   • ATTENTION: Leaking connection due to failed pressing sequence
   • Replace any connections that have not been pressed correctly. They must not be pressed again.
4. Press the Geberit pressfitting.
   • See operating instructions for the relevant pressing tool.
5. Push the ends of the jaw levers together and remove the Geberit pressing jaw from the Geberit pressfitting. Check the pressing contour.
   • If a press connection has not been completely pressed – in the event of a power cut, for example – it must be pressed again.
   • Corrective pressing is performed in the same way as a normal pressing operation.
   • Depending on the state of the preliminary pressing, there may be considerable idle stroke before the pressing tool engages during corrective pressing.

Maintenance

Maintenance regulations for Geberit pressing jaws

These Geberit FlowFit pressing jaws are low-maintenance and do not need to be tested by authorised repair shops if they are used as intended. However, pressing jaws still requires maintenance. Pressing jaws that are not maintained, or are not professionally maintained, can cause accidents and injuries.

It is essential to observe the maintenance intervals and maintenance work outlined below:

FlowFit pressing jaw for externally visible defects such as damage, material cracks, patches of rust and other signs of wear. Replace the pressing jaw if defects are present.

▶ Remove any deposits on the pressing tips.

▶ Spray the pressing tips with a lubricant recommended by Geberit and clean with a cloth.

▶ Test whether the jaw levers can move easily. Check for dirt between the jaw levers. If necessary, clean the jaw levers and move them several times until they can move easily.

Geberit FlowFit PowerTest to ensure that the distance between the pressing tips is permitted and that enough pressing force is provided. If defects are found during the inspection, the pressing jaw must be replaced.

Disposal

• Disposal of Geberit pressing jaws
  • Geberit pressing jaws are made of steel. Therefore, Geberit pressing jaws that are no longer in use do not belong in non-recyclable waste.
  • They must be directly returned to Geberit for proper disposal or sent to a local collection point for scrap metal.

Conformity

• Declaration of conformity for Geberit pressing jaws
  • Geberit pressing jaws are part of a system and do not have their declaration of conformity. The relevant declarations of conformity are included with the pressing tools.
• Person in charge of documentation
  • Jörg Schneider, Product Compliance, Geberit International AG,
  • 8645 Jona, Switzerland

CONTACT

• Geberit International AG
• Schachenstrasse 77, CH-8645 Jona
• documentation@geberit.com.
• www.geberit.com.
• 9007212209767563 © 01-2024 972.178.00.0(00)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>