ADLER CR 4223 Camry Robot planetarny LCD 2000W 5L User Manual
- June 6, 2024
- ADLER
Table of Contents
CR 4223
user manual
SAFETY CONDITIONS. IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial purposes.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V, ~50/60Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without
supervision. -
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or
knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the
dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless
they are over 8 years of age and these activities are carried out under supervision. -
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never
use the product in humid conditions. -
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid
hazardous situations. -
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let the cord hang over the edge of the counter.
-
For additional protection, it is advisable to install a residual current device (RCD) with a rated residual current in the electrical circuit.
-
Do not immerse the motor unit in water. Do not wash in dishwashers.
-
Before cleaning and removing accessories set the speed control to OFF position and unplug the power cable.
-
Before operating the device check if all parts and accessories are properly mounted.
-
During the mixing of hot products exercise extreme caution to avoid burning.
-
The device has been designed to prepare small amounts of food products. The device is not intended for industrial food processing.
DESCRIPTION OF THE DEVICE (figures 1 and 2 and 3)
1.Top of a food processor| 2. Tilt button| 3. Bowl 5,0 liters|
---|---|---|---
4. Base| 5. Bowl cover| 6. Speed selector
7. LCD time display| 8. LCD speed display| 9. Timer button
10. Plus button| 11. Minus button
A – Dough hook| B – Mixing beater| C – Egg whisk| D – Spatula
BEFORE USING A MULTIFUNCTION FOOD PROCESSOR
Before assembling the device, be sure the power cord is unplugged from the power outlet and the speed selector (6) is in the “0” position.
-
Press the tilt button (2), the top of the mixer (1) will automatically release and lock into the tilt position.
-
Select the desired attachment, which is depending on the mixture to be performed:
A – hook for kneading the dough,
B – mixing beater for mixing and beating eggs and butter,
C – egg whisk for beating and frothing the egg white/cream / liquid food. -
Insert the desired attachment directly, until it locks into the correct position – see figures 4 and 5.
Note: Ensure the attachment is fully inserted into the socket, otherwise your mixing result may be affected. -
Place the bowl (3) on the base (4), then turn the bowl (3) clockwise until it locks.
-
To lower the top of a food processor (1), press the tilt button (2) and push by one hand the top of the food processor (1) down. A click sound will be heard when the part has reached the correct position. Make sure the bow cover (5) is fixed in place (see figure 1).
USING
-
Ensure that the speed selector (6) is at the OFF position, then insert the plugin to the power source.
-
Turn the speed selector (6) to your desired speed setting from “0” which means OFF position till “6” means the fastest speed. The motor rotation speed number will be shown at the LCD speed display (8).
-
The time display (7) will show the time elapsed since the device was switched on until now It is a case, the timer is not set up, the timer is counting up time from start (0:00) to switch off moment.
TIMER SET UP
To set up the timer that is counting operation period from switch on to the desired moment in time and next switch off the device automatically,
follow up below steps:
• Press the timer button (9), the LCD time display (7) shows 00:30 – half a minute.
• Press repeatedly the plus button (10) to enlarge the operation time at intervals of 30 seconds.
• Press repeatedly the minus button (11) to reduce the operation time at intervals of 30 seconds.
• After selecting the desired period of operation the LCD time display (7) will flash 3 times to remember your setting. Next, the time display (7) will count down the operation time to 00:00. The motor will be stopped automatically, the LCD time display (7) will flash: 00:00, the LCD speed display (8) will show speed zero. -
To reach instantaneous maximum motor speed hold the speed selector (6) on position “P” – pulse. To mix the food by suitable attachment follow up below brief instruction:
Attachment A: suitable for speeds 1-2. Time of operation: at speed 1: 30 seconds, at speed 2: 5-6 minutes.
Attachment B: suitable for speeds 1-4. Time of operation: at 1-2 speeds: 1 minute and at speeds 3-4: 3-4 minutes.
Attachment C: suitable for speeds 5-6. Time of operation: 5-7 minutes. To whip the egg whites, use a minimum of 3 eggs, and a maximum of 15 egg whites.
Warning: Do not put the knife, metal spoons, fork, spatula, and so on into the bowl when it is operating -
The max operation time in one cycle shall not exceed 7 minutes. 10 minutes of minimum rest time must be maintained between 2 consecutive cycles. After 2 consecutive cycles let the unit rest by 40 minutes.
-
When mixing is completed, turn the speed selector to the “0” position, unplug the cord from the power outlet.
-
Hold down the tilt button (2), the top of the mixer (1) will automatically lift and lock into the tilt position.
-
If necessary, you can scrape the excess food from an attachment by plastic spatula (D).
-
Pull out the mixing attachment with a little force by turning to the left side and then down. The speed selector must be at “0” position and the power outlet must be unplugged before pulling out the mixing attachment.
The food processor will automatically switch off after the locked-rotor motor stop working for 15 seconds. The device can’t continually work for a long time, if work more than 2 cycles by 7 minutes, please wait for 40 minutes before the next mixing.
CLEANING AND MAINTENANCE
- Unplug the device from the power and let it cool down before cleaning.
- Remove the accessories before cleaning them in water with washing-up liquid. Do not wash in dishwashers.
- Wipe the external parts with a kitchen towel or soft cloth.
- Do not use abrasive materials to clean the device.
- Don’t immerse the base in water or other liquids.
TECHNICAL DATA
Power supply: 220-240V ~50Hz
Power: 1300W Max Power: 2000W
Stainless steel bowl 5 liters
Max operation time in 1 cycle: 7 min
Min rest time between cycle: 10 min
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.
| 
---|---
Documents / Resources
|
ADLER CR 4223 Camry Robot planetarny LCD 2000W
5L
[pdf] User Manual
CR 4223, Camry Robot planetarny LCD 2000W 5L
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>