ADLER GL 2932 Multifunctional Trimmer Set Hair Clippers Shaver User Manual

ADLER GL 2932 Multifunctional Trimmer Set Hair Clippers Shaver User Manual

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different, if the device is used for commercial purpose.”

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
3. The applicable voltage is 5V, ~1A. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
4. Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge  f the device, only under the supervision of a person responsible  for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device.  Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power  cable!!!
7. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
9. Never use the product with a damaged power cable or if it was dropped or  damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
11. Never use the product close to combustibles.
12. Do not let cord hang over edge of counter or touch hot surfaces.
13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
14. In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
15. If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off
16. Do not allow the device or power adaptor to wet.
17. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put hands in the water. Have the device checked by the qualified electrician before using it again.
18. Do not touch the device or power adaptor with wet hands.
19. Never use this device close to water, e.g.: under shower, in bathtube, or above sink filled with water.
20. If the device utilizes a power adaptor, do not cover it, because this can cause a dangerous temperature rise and can damage the device. Always connect the power adaptor cable to the device, and then connect the power adaptor to the power socket.
21. The shaver charging temperature should not be above 35 degrees Celsius or below 5 degrees Celsius.
22. Only the shaver head can be washed in water, the other parts of the shaver cannot be immersed in water. Be careful, the hot water can cause burns to your hands.
23. Do not use towel or paper tissues for cleaning of shaver head, as they can damage the head.

Device Description

Trimmer Set

1. Trimmer Head
2. Power Button
3. Display
4. Design Trimmer
5. Precision trimmer
6. Nose / Ear trimmer
7. Foil Shaver
8. Sideburn / Eyebrow / Body trimmer
9. Length attachments for the precision trimmer.
10. The docking station
11. Machine Oil.
12. Cleaning Brush
13. Charging cable.

Trimmer Charging

Before charging make sure, that the shaver is switched off. Charging takes about 1,5 hours. The shaver cannot be plugged into the power socket for longer than 24 hours.

1. Connect the charger cable to the shaver (fig. 16).
   
   

2. The Display(3) will illuminate. And the % of load will show. When it reaches 100% please disconnect the charger.

3. After full charging of the shaver, unplug the charger from the power socket, then disconnect the cable from the shaver.

4. DO NOT use your shaver while charging.

Using the device

1. Make sure the device is not turned on and then insert the needed attachment onto the device.
2. Press the Power button (2). Press it a second time to the second speed.
3. After usage clean the attachment with the brush (12).
4. After several uses please oil the attachment with machine oil (11).

Attachment Usage

1. Basic trimmer head (1)
   This attachment is used to prune and keep the beard looking stylish. Intended for daily use.

2. To remove and attach please consult Fig. 1, 2, 3. When attaching please align the inside part shown in fig. 3 subpoint 2 with the device’s groove in the device shown in fig. 3 subpoint 1. And then press firmly towards the device until it clicks into place.
   
   
   

3. To add the length attachment please consult Fig. 11, 12. And then press firmly towards the device until it clicks into place.
   
   
   To remove the length attachment please consult Fig. 7, 8.
   
   

4. Precision trimmer head (4)
   This attachment is used for places that the basic trimmer is too big or too wide to reach without cutting parts of your facial hair you don’t intend to cut.
   

5. Design trimmer head (5)
   This attachment is used to adjust the length of your facial hair. You can change one of the 5 length attachments in set (9)
   
   To remove and attach please consult Fig. 1, 2, 3. When attaching please align the inside part shown in fig. 3 subpoint 2 with the device’s groove in the device shown in fig. 3 subpoint 1. And then press firmly towards the device until it clicks into place.
   To add the length attachment please consult Fig. 11, 12. And then press firmly towards the device until it clicks into place.
   To remove the length attachment please consult Fig. 7, 8. This attachment has 1 attachment that has the option of regulation in 4 positions.

6. Nose trimmer (6)
   This attachment is used to get rid of nose and ear hair:
   To remove and attach please consult Fig. 1 When attaching please align the inside part shown in fig. 3 subpoint 2 with the device’s groove in the device shown in fig. 3 subpoint 1. Then firmly grab the attachment by the sides as shown in Fig. 6. Press firmly towards the device until it clicks into place.
   
   !!CAUTION!! AVOID PUTTING THE ATTACHMENT HEAD MORE THAN 6MM INTO YOUR NOSE OR EAR.

7. Foil Shaver (7)
   This attachment is used to shave off any excess hair around the face. It provides the closest shave.
   To remove and attach please consult Fig. 1 When attaching please align the inside part shown in fig. 3 subpoint 2 with the device’s groove in the device shown in fig. 3 subpoint 1. Then firmly grab the attachment by the sides as shown in Fig. 9. Press firmly towards the device until it clicks into place.
   
   

8. Sideburn / Eyebrow / Body trimmer (8)
   This attachment s intended for managing the length and shape of your eyebrows, sideburns, and body hair. It has an additional attachment that you can change the length or use without the attachment.
   To remove and attach please consult Fig. 1 When attaching please align the inside part shown in fig. 3 subpoint 2 with the device’s groove in the device shown in fig. 3 subpoint 1. Then firmly grab the attachment by the sides as shown in Fig. 25. Press firmly towards the device until it clicks into place.
   

TIPS FOR BEST RESULTS

Beard, mustache, and sideburn hairs should be dry.
Avoid using lotions before using your personal groomer. Comb your hair in the direction that it grows.
Remove trimmer comb attachment if you are: defining hairline edges such as sideburns, trimming the nape of your neck, trimming your beard line on the front of the neck.

Cleaning

After each use turn off the device.
Gently brush the remaining hair with the attached comb (12).
Only clean the comb attachments and blades once removed from the main device.
Only use light sewing machine oil or the oil attached to the device.
The device can be washed with water but please dry the device with a soft dry towel till dry before storing the device.

TECHNICAL DATA

Charging voltage: 5 V 1A
Power.: 5W

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>