AMP Lighting AUL-8002-B-BZ Low Voltage Landscape Lighting User Guide
- June 6, 2024
- AMP Lighting
Table of Contents
Lighting
INSTALLATION & MAINTENANCE GUIDE
AMP® Low Voltage Landscape Lighting
AMP® HydraPro MR11 Underwater Light
AUL-8002-B-BZ
Important Safety Instructions: Read Before Installation!
This fixture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance, or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this fixture.
- Warning: this fixture is not intended to be installed within 10 feet [3 meters] of a pool, spa, or fountain.
- This fixture is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Underground Low Energy Cable must not be buried over 6” (15.2 cm) in order to connect to the main low voltage cable.
- Wiring connections must be made with UL Listed wire connectors that are suitable for the application.
- Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
Important Safety Instructions!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted
lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before replacing the lamp.
- The lamp gets HOT quickly! Contact only switch/plug when turning on.
- Do not touch the hot lens, guard, or enclosure.
- Keep the lamp away from materials that may burn.
- Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage the lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
Package Contents
A. (1) Fixture Body
Parts Required
A. (1) MR11 Lamp (sold separately)
B. (3) Screws
C. (3) Flat Washers
D. (3) Anchors
Product Dimensions
Remove Faceplate and Lens
Use a screwdriver to loosen the screws on the faceplate and remove the lens from the fixture body.
Install Lamp
Insert the lamp with the correct wattage and type marked on the fixture label
and push firmly into place.
CAUTION: Do not exceed the maximum wattage marked on the fixture label.
Install Faceplate
Place the lens and the faceplate back onto the fixture body and secure the removed screws in a star pattern using a screwdriver. Tighten until snug.
Install Base
NOTE: Installations such as ponds or fountains do not require the fixture to be secured with screws. The fixture will be held into place using it’s own weight. In those cases, this step can be skipped.
- Place the base onto the desired location and mark three points on the ground for the anchors.
- Remove the base and drill proper holes for the anchors using the marks as guides.
- Push anchors into drilled holes.
- Attach the base onto the anchors by placing the washer onto the screw and threading the screw into the anchor to secure the base. Tighten the screw with a screwdriver.
Wire Connection
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the fixture body to the main supply cable leads.
Adjust Luminaire Direction
Using the Allen key, loosen the thumbscrew to rotate the fixture body to your desired direction. Always tighten the thumbscrew after adjustment.
Remove Faceplate and Lens
Use a screwdriver to loosen the screws on the faceplate and remove the lens from the fixture body.
Replace Faceplate
Place the lens and faceplate onto the fixture body and secure with previously removed screws in a star pattern. Hand tightens until snug with a screwdriver.
Faceplate Replacement Options
Install/Replace Lamp
Repeat step 1 – step 3 to remove the faceplate to expose the lamp and replace
it with the correct wattage and type marked on the fixture label.
Then, reinstall the faceplate.
IMPORTANT: Lamps must be protected from moisture and dust at all times.
Always reinstall the faceplate when removed.
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm
(EST)
Specifications and product details are subject to change without notice.
© Copyright 2020, AMP®
Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@amplighting.com •
813.978.3900
www.amplighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>