Watchguard ALL-PIR1 Wireless PIR Sensor User Manual

Wireless PIR Motion Detector & Door/Window Sensor
User Manual

Appearance:

1. Detection Window
2. Magnet
3. LED Indicator
4. Reed Switch
5. Tamper Switch
6. Infrared Sensor
7. RF antenna
8. Battery Compartment
9. Software Upgrading Terminal Block
10. Connector for Wired Sensors (N/C)

Note! The door sensor is set in Normal Zone1 as default. It will cause an immediate alarm if the magnet departs from the transmitter more than 2cm in an arming state.

LED Indicator:

LED flashes once every 2 seconds: PIR warming up
LED flashes once every 3 seconds: Lower battery, please replace the battery (AAAA LR61)
LED flashes once every 1 second: Detecting alarm/tamper alarm

Tamper Switch:
Once the case is opened, the tamper switch will be triggered.

Connecting Sensor to Control Panel:

1. Press the enroll button of the control panel, the control panel enters into enrolling status, the LED lights up in red. (Press again the enroll button within 20 seconds to exit enrolling state.)

2. Connecting PIR sensor to control panel: power on or trigger the PIR sensor.
   Connecting door sensor to control panel: depart the transmitter and magnet. (Enrolled by PIR, the default zone is home mode 1, enrolled by door sensor, the default zone is normal zone 4).

(Note! Please don’t press tamper switch to enroll or enroll accessory in low battery status.)

Enrolling Way

| Power On| Connecting Door Sensor|

Connecting PIR Motion Sensor

---|---|---|---
Detector| Door Sensor| PIR Motion Sensor| Door Sensor| PIR Motion Sensor| Door Sensor| PIR Motion Sensor
55-P01 PLUS
FHSS Frequency Sensor Zone Type| Wireless
Zone 4| Home Model
(Wireless Zone 1)| Wireless
Zone 4| Home Model
(Wireless Zone 1)| Wireless
Zone 4| Home Model
(Wireless Zone 1)
SS-P01
Normal Frequency Sensor Zone Type| Wireless Zone 1| Wireless Zone 1| Home Model (Wireless Zone 5)

Note: Wireless sensor zone type will be separated according to the sensor for the FHSS series.
While normal frequency sensor types will not be separated.

PIR Working Mode:

Testing Mode:

When powered on, PIR starts to warm up, LED backlight flashes for 15 seconds to enter the testing mode. In this mode, it will enable the LED indicator to light and control panel to alarm every time once a movement is detected. After five detections, it enters into sleeping mode. And the door sensor enters working mode.

Sleeping Mode:

The sleeping time of PIR is approximately 3 minutes to save power. No movement is detected within 3 minutes, the PIR detector goes back to the working mode. Once PIR is triggered, the PIR will light in red and alert alarming. PIR will re-enter into sleep mode after 2 times detections during the working mode. Any movement detected within 3 minutes, the PIR will not light in red and the alarm will not be activated. And it will extend the sleep time by another 3 minutes.

Walk Test:

1. After the warm-up, PIR enters into a working state.
2. Walk across the detection area and watch the LED indicator to make sure it flashes once when detecting the movement and send a signal to the alarm panel.

Door/Window Working Mode:

The Door/Window Sensor can be installed on doors, windows, and any other objects that open and close. The sensor transmits a signal to the control panel when the magnet mounted near the sensor is moved away. The tamper protection ensures that sabotage attempts to move the sensor will result in alarm activation.

Installation:

1. The sensor should be installed in entry or exit which intruder can easily enter.
2. Sensors can be installed on doors or windows that open and close. Make sure the installed position has been already cleaned.
3. Remove the paper strip of the double-sided tape on the back of the transmitter and magnet. Carefully mount the transmitter on the door frame and the magnet on the door.
4. Or you can fix the rear base on the place by using the screws for both transmitter and magnet.
5. Magnet can be placed on both the left or right sides of the transmitter.
6. The sensor is more sensitive to cross-movement than to direct movement. The performance of the detector is optimal when the detection direction is across the walking direction of intruders.

Detection Mode & Area:

Normal Mode:

It’s recommended to mount it at the height of 1.7m from the ground.
Detection range is 90 degrees, with 8 meters range.

Pet-immunity Mode:

It’s recommended to mount it at the height of 1.5m from the ground and put the lens upside down for pet immunity.
Detection range is 90 degrees, with 8 meters range. The height limit for animals is 1.2 meters.

Connect the Wired Output Interface：

There are two terminal blocks that can connect any N.C output wired sensor.

Notice:

1. Avoid mounting the detector close to places where heat changes fast or the airstream flows frequently. (ie. Air conditioner, tube light, oven, waver, refrigerator, etc.)
2. Avoid it facing the window which can be easily interfered with by a complicated environment. (ie. sunlight, crowds, or flowing cars, etc.)
3. If two detectors are installed in the same detection scope, please adjust the location to avoid interference and false alarm.
4. Place the transmitter in the desired location, mount the magnet no more than 1cm away from the transmitter.
5. Avoid mounting sensors in areas with a large quantity of metal and electric wiring.
6. The product can reduce the possibility of accidents, but the user is advised to take all necessary precautions for the safety and protection of the property.

It’s specially designed for request-to-exit applications, combines a PIR motion detector & door/window sensor. It detects the opening or closing of a window, door, gate, or roller blind and indoor human movement. Adopted advanced fuzzy logic chip and intelligent analysis distinguish signal between body movement and interference to minimize false alarms. Cover tamper detection and state & low battery indication ensure safety.

Features:

Stylish compact design, easy to install.
The modern design will compliment any interior.
Combines PIR & Door Sensor, double security.
LED backlight indication for alarm status & low battery.
Customized high-quality lens, pet-immunity.
PIR sleeping mode for low-power consumption.
FHSS technology, anti-interference, protect from blocking.
Long battery life for 1 year.
Adopt US Perkinecmer LHI968 chips high-end element.
Special RFI protection, high performance, low noise.
Tamper protection.

Specification:

Power Supply: DC 3V (2pcs of AAAA, LR61 Battery)
Standby Current : SS-P01: ≤45μA
SS-P01 PLUS: ≤50μA
Alarm Current : SS-P01: ≤26mA
SS-P01 PLUS:≤39mA
Temperature: -20°C~55°C
Humidity: ≤80% (no condensing)
Detector Dimensions(L x W x H): 21 X 90 X 18mm
Magnet Dimensions(L x W x H): 10 X 45 X 11mm

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>