Watchguard AP330 WiFi 6 Wireless Access Point User Guide
- June 6, 2024
- Watchguard
Table of Contents
Watchguard AP330 WiFi 6 Wireless Access Point
WHAT YOU NEED
ACTIVATE YOUR AP
GO TO:
watchguard.com/activate
MOUNT THE AP
CEILING MOUNT
WALL MOUNT
**Use the included spacers if you mount to a wall with the 15/16″ bracket attached to the access point.
**
CONNECT THE AP
Plug one end of the Ethernet cable from your network into the LAN PoE+ port on
the bottom panel of the AP. Make sure the other end of the Ethernet cable is
connected to your network through a hub, switch, or injector with PoE+
(802.3at) power enabled.
CONFIGURE AND TROUBLESHOOT THE AP
GO TO:
watchguard.com/start
NOTICES
All WatchGuard products are designed and tested to meet strict safety
requirements. These requirements include product safety approvals and other
global compliance standards. Please read these instructions carefully before
operating the product, and refer to them as needed to ensure the continued
safe operation of your product. Additional information, including a full list
of safety approvals, global compliance standards, and certifications can be
found in the Hardware Guide for this device located on the WatchGuard website:
https://www.watchguard.com/wgrd-help/documentation/hardware-guides
For patent information, please visit
http://www.watchguard.com/patents
Safety Warning
If protective earthing is used as a safeguard, the instructions shall require
connection of the equipment protective earthing conductor to the installation
protective earthing conductor (for example, by means of a power cord connected
to a socket-outlet with earthing connection). To meet safety and
electromagnetic interference (EMI) requirements, you must make sure the power
source is connected to earth ground before you connect power to the AP.
Power Adapter Requirements
This product is intended to be supplied by a Listed Power Adapter or DC power
source marked “L.P.S.” (or Limited Power Source or PS2) rated 12V DC, 2A
minimum, maximum ambient temperature (Tma)=40°C, or supplied by a Listed PoE
Adapter marked “L.P.S.” (or Limited Power Source or PS2) rated 48V DC, 0.6A
minimum, maximum ambient temperature (Tma)=40°C. For more information
regarding approved power sources, please contact WatchGuard Technologies.
This product is for indoor use only.
Declaration of Conformity
WatchGuard Technologies Inc. hereby declares that the product(s) listed below conform to the European Union directives and standards identified in this declaration.
Product (s): 802.11 a/b/g/n/ac/ax Access Point, AP330
EU Directive(s): Low Voltage (2014/35/EU) Electromagnetic Compatibility
(2014/30/EU) Energy-related Products (2009/125/EC) RoHS (2011/65/EU and
2015/863/EU RoHS) WEEE Directive 2012/19/EU The Radio Equipment Directive
(2014/53
Common Standard(s):
EN 62368-1:2014+A11:2017 Safety for ITE
EN 55024:2010
EN 55024: 2010+A1:2015 Immunity for ITE
EN 55032:2015+A11:2020
EN 55035: 2017
EN 61000-3-2:2014 Harmonics
EN 61000-3-3:2013 Flicker
Wireless Standard(s):
EN 62311:2008
EN 301 489-1 v2.2.3 (2019-11) EMC and Radio Spectrum Matters
EN 301 489-17 v3.1.1 (2017-02) EMC and Radio Spectrum Matters
EN 300 328 v2.2.2 (2019-07) Radio Spectrum Matters
EN 301 893 v2.1.1 (2017-05) Broadband Radio Access Networks
EN 50385: 2017
Warning
This is a Class B product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
WATCHGUARD TECHNICAL SUPPORT
1.877.232.3531
(U.S. and Canada)
+1.206.613.0456
(all other countries)
http://www.watchguard.com/support
ADDRESS : 505 Fifth Avenue South, Suite 500, Seattle, WA 98104 U.S.
SALES: 1.800.734.9905 • INTERNATIONAL SALES: +1.206.613.0895
WEB : www.watchguard.com
© 2022 WatchGuard Technologies, Inc. All rights reserved. WatchGuard, the
WatchGuard Logo, Fireware, and LiveSecurity are registered trademarks of
WatchGuard Technologies, Inc. in the United States and/or other countries. All
other trademarks and tradenames are the property of their respective owners.
P.N. 352-4330-001 Rev B 011222