ADLER AD 7714 Heater Instruction Manual

: June 6, 2024
: ADLER

Table of Contents

GUIDELINES FOR SAFETY OF USE
WARNINGS
BEFORE FIRST USE
CLEANING AND MAINTENANCE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AD 7714
Instruction Manual

This product is suitable only for occasional use or for use in well-insulated rooms.
Model identifier

Item	Symbol	Value	Unit

Heat output
Nominal heat output| P nom| 1,939| kW
Minimum heat output

(indicative)

consumption

| | |
At nominal heat output| el max| 0| kW
At minimum heat output| el min| 0| kW
In standby mode| el SB| 0,00051| kW
Contact
Item| Unit
---|---
Type of heat input, for electric storage local space heaters only (select one)
manual heat charge control, with integrated thermostat| [no]
manual heat charge control with room and /or outdoor temperature feedback| [no]
electronic heat charge control with room and /or outdoor temperature feedback| [no]
fan assisted heat output| ****
Type of heat output/room temperature control (select one)| [no]
single-stage heat output and no room temperature control| [no]
two or more manual stages, no room temperature control| [no]
with mechanic thermostat room temperature control| [no]
with electronic room temperature control| [yes]
electronic room temperature control plus day timer| [yes]
electronic room temperature control plus week timer| [yes]
Other control options (multiple selections possible)
room temperature control, with presence detection| [no]
room temperature control, with open window detection| [yes]
with distance control option| [no]
with adaptive start control| [no]
with working time limitation| [no]
with black bulb sensor| [no]
Adler Sp. z o.o. ul. Ordona 2A, 01-237 Warszawa, Polska

ATTENTION:
The device is intended for domestic use only.
The device is NOT intended for commercial/professional use.
The device is NOT suitable for use outdoors.
Attention! Before use, it is essential that you read these operating instructions to avoid accidents and for the correct use of the device. Keep this manual and keep it so that you can easily use it.

GUIDELINES FOR SAFETY OF USE

Before use, check that the voltage specified on the nameplate corresponds to the local parameters of salinity, but remember that the marking: AC- is alternating current and DC is DC.
Connect the device only to a 220-240V ~ 50/60 Hz grounded outlet.
Before use, unroll and straighten the power cord
Make sure that the power cord and plug have no visible damage
Before and during use, make sure that the power cord is not stretched over an open flame or another source of heat and has sharp edges that can damage the insulation of the cable.
Before first use, remove all packaging components. Attention! In the case of a casing with metal parts, on these elements, a slightly visible protective foil can be stretched, which should also be removed.
The device should not be used by children, persons with limited physical, sensory or mental capacity without the supervision of authorized or experienced persons and always in accordance with these instructions.
The equipment is not intended for use with external time switches or a separate remote control system.
WARNING: This equipment may be used by children over 8 years of age and persons with limited physical, sensory or mental ability, or persons who have no experience or knowledge of equipment, ONLY if this is done under the supervision of a person responsible for their safety or have been given instructions about the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and maintenance of the device should not be performed by children unless they are over 8 years of age and are supervised Do not leave the device unattended during operation.
Do not immerse the appliance and the power cord in water or any other liquids.
When the device is not in use, it should always be disconnected from the power outlet.
When pulling the plug from the socket, never pull the power cord by the plug only.
Do not put NO METAL ITEMS inside the device
The manufacturer is not liable for damages resulting from improper use of the device.
It should be remembered that some parts of the device and the cabinet during work get very hot, so be careful and do not touch them, you can get burned.
NEVER cover the device during operation or when it does not cool down completely
Remember that the heating elements of the device take time to cool down completely.
When using the device, ensure adequate space above and around. The device must not touch any easily flammable objects during work, such as decorations, paper towels, curtains, clothing, etc.
The heater installed in the bathroom should be installed so that connectors and other regulators can not be touched by a person in the bathtub or under the shower.
In heaters for high-altitude fixtures, the positions of the different positions of the connectors should be visible from a distance of 1 m
The labeling for covering the heater should be visible after installing the heater
You can not place the heater directly under the socket and near flammable materials such as curtains, curtains, etc.
The device can not be used with external time switches or other separate remote control systems
Do not expose the device to atmospheric conditions (rain, sun, etc.) or use in conditions of high humidity (bathrooms, damp camping houses)
Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair facility in order to avoid a hazard
Do not use the device near flammable materials
The heater must be installed at a height not less than 1.8 m above the floor
Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
Do not use this heater if it has been dropped
Do not use if there are visible signs of damage to the heater
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer.

WARNING: Do not use this heater in small rooms where there are people who are unable to leave them by themselves unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at least 1 m away from the heater air outlet.
It is recommended that the electrical installation be equipped with an automatic residual current circuit breaker with a 30mA starting current for increased safety.
Note : If the power cord or power plug is damaged, it should always be replaced or repaired by a specialized repair shop.

WARNINGS

Never use the device if it is damaged or does not function properly.
Never use the device if it has fallen from a height before and shows visible signs of damage.
Do not use extension cords or other electrical outlets that do not meet the applicable standards and electrical regulations.
Any repairs, dismantling or replacement of any parts should always be made by a specialized facility.
If the device and elements such as electrical contacts are wet, the plug or cable should be dried before using the device and its components.
Do not use the device with wet hands.
When there is a risk that the device has been damaged NEVER try to repair the device yourself.
Never wash the device under running water or in such a way that water drips into it.
Do not use accessories that are not recommended by the manufacturer. They may pose a danger to the user and may cause damage to the device.
Ensure that the device has cooled down before storing.
Do not touch the housing during use. During operation, use only knobs and switches.
After switching off, wait for the device to cool down.
CAUTION: Some parts of this device may become very hot during operation and cause burns.

BEFORE FIRST USE

Remove all packing material and straighten the power cord
During installation, in no case may the device be covered with insulating material or similar material
When assembling the device, beams and rafters should not be cut or cut
Before first use read all instructions for use.
Check if the voltage listed on the product rating label corresponds to the voltage of the power network in your home

INSTALLATION
Use a drill to drill two holes in the wall, a minimum of 180 cm from the floor and 20 cm from the ceiling – picture A. Once you have drilled the holes, insert the pad and screw. Make sure the screws are well tightened then hang the device on the wall.
PRODUCT DESCRIPTION
Picture B. MAIN SWITCH
ON/OFF = TURN ON /TURN OFF.
Picture C. REMOTE CONTROLER

1. ON/OFF button
2. MODE
3. DAY
4. CLOCK
5. SET UP
6. WEEK/TIMER
7. MIN| 8. + -> Button for raising the temperature. Also serves as a selection button for time/day.
9. – -> Button for lowering the temperature. Also serves as selection button for time/day
10. RESET – Timer reset button
---|---

Picture D. LED PANEL

1. ON symbol
3. Heating power 2000W
5. Temperature display
7. Time display
9. OFF symbol – timer shutdown| 2. Heating power 1000W
4. AUTO function
6 .Day display
8. ON symbol – timer startup
10. Open window detection function
---|---

USING

Press the main switch on the right side of the device – Picture B to switch the device on and off.
The device is now in standby mode. Press the on / off button (1) on the remote control – Picture C.
Press the MODE button (2) in turn to select the operating mode:
– 1000 W the device will constantly heat up with 1000 W.
– 2000 W, the device will constantly heat up with 2000W.
– Auto mode, press the + and – buttons to manually set the temperature. The device will automatically enter the temperature maintenance mode.
– Open window detection function – When this function is selected, the device will automatically turn off the heating if the room temperature drops suddenly by 10 ° C.
To turn off the device, press the on/off button (1) on the remote control. The device cools down and turns off after about 30 seconds.

SETTING THE INTERNAL DEVICE CLOCK
NOTE: If you do not set the current time and day of the week, the device will not work properly because it will operate according to its own internal clock, which is incorrect.

Select the AUTO function using the MODE button.
Before setting the timer, set the day of the week and the current time:
– Press the DAY button and select the current day using the + and – buttons. Wait until the display stops flashing.
– Press the CLOCK button and set the current time using the + and – buttons. Wait until the display stops flashing.
– Press the MIN button and set the current minutes using the + and – buttons. Wait until the display stops flashing.

TIMER PROGRAMMING SETTING – TIMER
This function allows you to program the time to turn on and off the device on each day of the week at the desired time.
The timer can only be set after selecting the AUTO function and setting the device’s internal clock.

Press the WEEK / TIMER button and select the day of the week on which you want to set the device to switch on and off automatically using the + and – buttons. Wait until the display stops flashing.
After pressing the SETUP button, the ON symbol will light up in the display. You can now set the timer start time. Use the CLOCK, MIN, +, and – buttons to set the timer start time. Wait until the display stops flashing.
After pressing the WEEK / TIMER button (6) again and then pressing the SETUP button, the OFF symbol will light up in the display. You can now set the timer off time. Wait until the display stops flashing.

NOTE: the start time must always be lower than the stop time.
NOTE: To reset the timer to default settings, press the RESET button.

CLEANING AND MAINTENANCE

Always unplug the appliance from the power socket before cleaning.
If during cleaning items such as the power plug, thermostat electrical contacts, etc. are soaked before being used again, they should be thoroughly dried
Do not use aggressive detergents in the form of emulsions, lotions, pastes, etc. to clean the cabinet. They can, among other things, remove the information graphic symbols, such as signs, warning signs, etc.
Ensure that the device has cooled down before cleaning.

TECHNICAL DATA:
Voltage: 220-240V ~50/60Hz
Power: 2000W Max. Power: 2200W
Ip20
**** “Caution Hot Surface” – The temperature of available surfaces may be higher when the equipment is working, which means that the housing elements become very hot during operation, SAVE CAREFUL !!!

DO NOT COVER« INSCRIPTION IMPORTANCE
The inscription on the device means that the device is not to be covered with clothing, blankets, and other textile products which could cause ignition.

WARNING: Do not use this equipment near bathtubs, showers, swimming pools, and similar water tanks.
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.

WWW.ADLEREUROPE.EU