Kruger Matz KM0552 Explorer Portable Wireless Speaker Owner’s Manual

Kruger Matz KM0552 Explorer Portable Wireless Speaker Owner’s Manual

SAFETY INSTRUCTIONS

Read the instruction manual carefully before first use and keep it for future reference. Producer is not responsible for damages caused by inappropriate handling and use of the device.

1. Protect this product from moisture, humidity, water and any other liquid. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and sources of heat.
2. Keep the volume at a reasonable level throughout entire time of using the speakers. To prevent damage to your hearing, do not raise the volume too high.
3. Stop using the speakers if you feel a tinnitus, hearing discomfort, irritation or have other adverse reactions.
4. Disconnect the device from the power supply if it is not going to be used for a long time.
5. Use only authorized accessories.
6. Do not place heavy objects on the device.
7. Do not attempt to repair this device yourself. In case  of damage, contact with an authorized service point for check-up/repair.
8. ALWAYS disconnect this device from power supply mains before cleaning.
9. Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.

PRODUCT DESCRIPTION

1. BT button
2. Previous track/ decrease volume
3. Power/ mode button
4. TWS button
5. Next track/ increase volume
6. Play/ pause/ call management
7. Battery level/charging indicator
8. Microphone
9. Reset socket
10.  microSD card slot
11. USB Type-C charging socket
12. AUX input
13. USB input
14. USB output (charging external devices)

OPERATION

Turn on/off

Press and hold the power button for about 2 seconds to turn on the device (blue back light of the power button lights up). The device will issue a voice prompt and automatically enter Bluetooth pairing mode.
Press and hold the power button again to turn off the device (blue back light of the power button goes off).

If after pressing the power button, the device is not turning on, it may be due to low battery. Please charge the battery and try again.

Play/ pause music

Press the play/ pause button.

Previous/ next track

Press the – button to go to previous track. Press the + button to go to next track.

Decrease/ increase volume

Press and hold the – button to decrease volume. Press and hold the + button to increase volume.

Answer/ end/ reject call

Press the play/pause button to answer/end call. Press and hold this button to reject call.
Note: Remain within 1 meter from the speaker’s microphone for the best call quality.

PAIRING

1. Press and hold the power button for about 2 seconds to turn on the speaker. It will automatically enter Bluetooth mode* (blue back light of the power button blinks quickly).
2. Please keep the speaker and external device close to  each other when pairing.
3. Enable Bluetooth function on the external device and search for new Bluetooth devices.
4. Select and connect with this device (KM Explorer). Enter password “0000” if necessary.
5. The speaker will issue a voice prompt signifying a successful pairing; blue back light of the power button stops blinking.
6. When playing music, blue back light of the power button blinks slowly. When music is paused, blue back light stops blinking.
   • If the device will not enter Bluetooth mode automatically after power on or if you want to switch to Bluetooth mode, press the BT button to manually enter pairing mode.
     Press and hold the BT button for about 2 seconds to disconnect with current external device and reenter pairing mode

Notes:

• Every time the speaker is switched on, it will connect to last connected device automatically. Please note, your device must be on with Bluetooth function turned on.
• The device will turn off automatically after about 10 minutes of no operation.

AUX MODE

1. Use the 3,5 mm jack cable and connect one plug of the cable to the speaker’s AUX input.
2. Connect the other plug into the 3,5 mm output of the external device you wish to play music from.
3. The device should automatically enter AUX mode. If jack cable has been connected to the speaker before power on, press the power button to enter AUX mode (back light of the power button should change from blue to white).
4. Start playing music from your device.
5. During music playback, white back light of the power button blinks. When music is paused, white back light is on.
6. Control music playback and volume from the speaker. Use connected external device to select desired track.

USB MODE

1. Connect the USB drive to the USB input of the speaker.
2. The device should automatically enter USB mode. If USB drive has been connected to the speaker before power on, press the power button to enter USB mode (back light of the power button should change from blue to white).
3. Start playing music from your device.
4. During music playback, white back light of the power button blinks. When music is paused, white back light is on.
5. Control music playback, volume and track selection from the speaker.

MICROSD CARD MODE

1. Insert the microSD card into the appropriate slot of the speaker.
2. The device should automatically enter microSD mode. If microSD card has been inserted into the slot before power on, press the power button to enter microSD card mode (back light of the power button should change from blue to white).
3. Start playing music from your device.
4. During music playback, white back light of the power button blinks. When music is paused, white back light is on.
5. Control music playback, volume and track selection from the speaker.

CHARGING

1. Connect USB Type-C plug of the included charging cable to the USB Type-C socket of the speaker.
2. Connect the other plug to the compatible PC USB port or AC charger.
3. When the battery is charging, charging indicators are blinking.
4. When the battery is fully charged, all charging indicators are on.
5. Disconnect the charging cable from the speaker and power source.

CHARGING EXTERNAL DEVICE

1. Make sure the speaker is turned on.
2. Connect the external device with the USB cable (not included in the set) to the USB output of the speaker.
3. Charging should start automatically.

TWS MODE
You can connect only the speakers of the same model.
You can connect speakers only when in Bluetooth mode.

1. Make sure the speaker A is already connected with the external device.
2. Turn on the speaker B.
3. Press and hold the TWS button of the speaker A for about 3 to 5 seconds. White back light of the TWS button blinks.
4. After successful connection between the speakers, white back light of the TWS button is on.
5. Now both speakers should simultaneously play music.
6. You can disconnect the speakers by pressing and holding the TWS button on either speaker for about 3 seconds.
7. Manage all functions using buttons on either speaker.

RESET

If abnormal condition occurs to the device during use, insert hard and slim object (for example a toothpick or a clip) inside the reset socket until the button is pressed. The speaker should reset.

SPECIFICATION

• Built-in microphone

• Hands-free function

• Call management

• Charging external devices

• TWS function (connect two speakers)

• Output power: 2x 6 W + 18 W

• Impedance: 4 Ohm

• 3 speakers: 2x 72 mm (tweeter) 1x 93 mm (subwoofer)
  Frequency response: 60 Hz ~ 20 kHz

• THD: <10%

• S/N ratio: >70 dB Bluetooth 5.0

• Bluetooth profile: HFP v1.7, AVRCP v1.6, A2DP v1.2

• Bluetooth range: up to 10 m

• I/O:
  1x USB Type-C charging port 1xUSBinput
  1xUSBoutput (charging at 5 V / 1 A)
  1x microSD card slot (up to 64 GB)
  1x AUX input (3,5 mm)

• Playback time: up to 7 h

• Battery: 7,4 V; 2000 mAh

• Charging: 5 V / 1 A

• In  set: USB Type-C charging cable, strap, user’s manual

LEARN MORE

For more information on this product, go to www.krugermatz.com.

Visit www.krugermatz.com website for more products and accessories.

In case of any doubts or questions reach out to our Frequently Asked Questions section.

Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that Portable Bluetooth speaker KM0552 is consistent with directive 2014/53/UE.
Full text of the EU Declaration of Conformity is available at following Internet address: www.lechpol.eu.
Correct Disposal of This Product **
(Waste Electrical & Electronic Equipment)**

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm lo the environment or human health fro uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.

Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne

www.krugermatz.com

Kruger &Matz is a registered trademark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>